Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

Gorilla Glue removal

Posts

Re: Gorilla Glue removal

#26

Re: I  promise . . .

William Duffield

Thank you, Richard and Bill for the clarifications. I'll keep it in mind for use in the appropriate applications, and I'll make sure to always wear my nitrile gloves (as I do when I'm using epoxy). It sounds like it's just the stuff for building shaving horses, sawbucks, pergolas, cold frames, greenhouses, outdoor signs, etc., from PTSYP or black locust.

Re: Gorilla Glue removal

#27

Re: Advantages ?????

Howard Acheson

I agree with Steve. Here's a write-up I did for woodworking club newsletter when Gorilla Glue first came out.

First, let me say I am not a fan of the poly glues primarily because I have found no advantage to them over standard PVA glues when gluing wood to wood joints except for gluing oily, exotic woods. "Creep" is much less of a problem but there are other adhesives that are creep resistant such as plastic resin and hide glue. I'm sure there are other opinions however.

That said, like any PVA glue (white or yellow) the poly's are no stronger than the wood itself--and may be weaker if they are not used correctly. In some recent tests in a woodworking magazine, Gorilla Glue was significantly weaker than PVA adhesives. Poly adhesives cure by a reaction with moisture but many use too much adhesive and moisture. Excess moisture increases the reaction but shortens open time--one of their claimed benefits--and results in excessive foaming and a weaker joint. If the wood is at a moisture content of 10% or more, additional dampening is probably detrimental, not helpful. There are now PVA glues with extended open time. In fact the white PVA has virtually exactly the same open time as the poly. The yellow PVA was formulated originally to respond to woodworkers who wanted a faster setting adhesive. Strangely, some poly glues are now being marketted that have a shorter open time and faster cure because some wood workers have complained about the longer clamp time required for the original polys. For normal, non-submerged outdoor use, a type II adhesive will work as well.

While "gap filling" they fill gaps with foam which has no strength. The adhesive expands as it cures tending to force glued surfaces apart so tight clamping is required. They also require that the clamp pressure be maintained for much longer than most other adhesives. Many find poly adhesive unsuitable for laminations as the agressive expansion pushes surfaces apart.

It contains hazardous materials and should be used in a ventilated area and kept away from skin if you believe the Material Safety Data Sheet. If it gets on your hands, only time will will remove the stain.

Finally, they cost much more than other glues and IMO, do not offer many advantages over less expensive adhesives.

Re: Gorilla Glue removal

#28

Re: agree....

Barry Irby

Years ago I built a gazebo out or redwood. I will have to post a picture. It has 12' diameter outer ring and eight arches that spring to a central octagonal point. There are eight columns about ten feet tall and a finial on top. the finial is 42" tall. I laminated the arches using Gorilla Glue because it was water proof and I don't think they had come out with Titebond III at the time. It has held up well. With the left over glue I glued up a arch out of treated pine that I resawed to about a 1/4" thickness. I made a mailbox post out it and it has held up fairly well in spite of not having any finish. Its eight or ten years old now.

Re: Gorilla Glue removal

#29

Re: Which is not the point.

TomD

The point I was clearly making was what happens of you get it on the skin, since that is what this thread discusses.

The nub of that is:

"The result

of that is that you now have on your hands methylene

dianiline, which is a really excellent and very efective

carcinogen. The safe exposure level for that stuff is "run

away at high speed".

That is either true or false. And I don't know one way or another, nor do I know any better from your response.

It has nothing to do with exposure to volatile isos, which by the way are available in .5% amounts. Though the product MSDS is not complacent about what you should do to avoid exposure to the glue in uses where it is in the air. The main issues being sensitisation, asma, fluid in the lungs, heart attack, cancer. 50% of what is in the glue is a commercial secret.

There is high variability in what happens to people as far as sensitization is concerned. So you can drop at first exposure, or take a while to develop it, or not be affected. Many sources, including Dow say that skin exposure may lead to lung sensitization. This can be inconvenient because other examples of this stuff are in insulation, furniture foams, and so forth.

In the real world, some people like to know whether stuff is edible, or not. You can eat a lot of good glues and finishes, then there are the ones that come with 10 page MSDSs and lots of experts to tell us how safe they are. There are two extremes to this. There are the articles as per a cover story on FWW were a guy was elbow deep in epoxy with no protections, and as a pro, may have done this a fair bit. These people need to get a clue. But at the other extreme there are people who know they can never know and prefer to stay away from what they don't understand. A method that has informed Warren Buffet's ascent to the richest man on earth, at times. Don't mess with what you don't understand. I certainly have no problem with people who want to play as they wish between the two extremes, but they are on their own. The extremes are pretty clear.

Re: Gorilla Glue removal

#30

Re: I  promise . . .

TomD

Epoxies will also set on soaking wood, including under water repairs to boats. The recent All Is Lost movie drove me crazy as far as his repair to his boat was concerned. Of course, epoxies have their curses also.

Kiln dried wood is just air dried wood once it is out of the kiln a while. I haven't had any problem with using so called dry wood for outdoor stuff, but I am sure you are correct there are special uses. That is why I have every glue known to man on hand. There is always something they are good at. What about green woodworking, where one assembles chair parts of dissimilar moisture. The only glues I buy a gallon or more at a time are titebond 1, epoxy, and 185 hide.

Re: Gorilla Glue removal

#31

Re: I  promise . . .

Sgian Dubh

"Epoxies will also set on soaking wood, including under water repairs to boats. The recent All Is Lost movie drove me crazy as far as his repair to his boat was concerned. Of course, epoxies have their curses also."

I'm aware that epoxy resins are used in that manner, but I've seen epoxy resins fail in green woodworking often enough. It may have been the way it was used rather than anything inherently unsuitable about the adhesive itself - I don't know one way or another. I know nothing about the movie you mention though.

"Kiln dried wood is just air dried wood once it is out of the kiln a while."

I think of kiln dried wood is air drying from the moment the kiln is turned on to dry a batch. It's just that the kiln, whichever type is in use, provides additional control to the process, including setting a target MC.

"I haven't had any problem with using so called dry wood for outdoor stuff, but I am sure you are correct there are special uses."

It's not so much there being special uses, but why pay a premium for kiln dried wood when air dried wood is almost always cheaper, or at least it is here in the UK? Secondly, if you are using thick timbers, such as European oak from about 120 mm square upwards, this stuff is seldom kilned because the material is so refractory. Of course it's possible to build artefacts destined for exterior locations out of kiln dried wood at, say, 7 or 10% MC - you just need to allow for the fact that the wood will expand as it takes on moisture.

" What about green woodworking, where one assembles chair parts of dissimilar moisture."

It's not all green woodworking though is it? You're talking about Windsor chair-making and similar country style furniture. In the UK, in one facet of the industry chair seats were usually air dried to about 20 - 25% prior to working them, and the legs and spindles were turned green thinnings from coppiced beeches found in the hills and valleys near High Wycombe, then stacked above a heat source for a period to dry them. Slainte.