Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Compare cordless drills on the numbers that matter

jointer

Posts

jointer

#1

jointer

Rodger

i am looking to add the bridgewood bw6r to my shop i read the report on it and think it would be a good fit in the report the assembly instructions and manuals were not real good i would like to know if this was looked at and fixed. One other thing i would like to know if there is a show room in york pa.i live in reading pa.and if i want this jointer can i pick it up

Re: jointer

#2

Re: jointer

Larry Clinton At Frankfort, (Central) Indiana

Can't help with any Bridgewood information, however I have purchased 2 jointer's from Grizzly and really think they are the best buy for the quality. Jointers are pretty simple machines, so if the quality is comparable, price, service and part availability are the only things I was concerned about. I had a 6" entry level Griz for about 15 years - it worked perfectly and was still straight and true after a lot of mishandling and use. I replaced it with a Grizzly 8" with the spiral /serrated Carbide inserted head about 7 years ago. I would purchase the same jointer again. Might pay to look at some reviews of the Grizzly's and compare prices!

Re: jointer

#3

JL

Re: jointer

JL

I always say a few things about jointers.

Buy the heaviest you can stuff in your shop with the longest table.

No body has ever really said - I bought too big of a jointer :b .

American Woodworker (among others) likes it and rates it a good buy.

You could also go to Muncy, PA and look at Grizzly.

Re: jointer

#4

Re: jointer

Paul Blackwell

I had an eight inch Grizzly jointer and sold it when I downsized after building a new house. I replaced it with a six inch Grizzly with spiral head and indexable carbide inserts. It's the smoothest cutting jointer I have ever owned. Cuts are so smooth that a bit of sanding is all that's required and it's good to go. I'd love an eight inch, but getting it down the stairs to the basement shop would be pretty tough.

Re: jointer

#5

Re: jointer

Larry in NW Ohio

Rodger If you live close to Springfield, Missouri, they have a big store there. Larry

Re: jointer

#6

Re: jointer

Tom

Take a dead flat rule, a machinist type deal. If you are going to Grizzly to buy, maybe you can borrow one. Standards go up and down. When I bought my jointer, Delta was still made over here. All the jointers I measured were badly out of whack in the flatness of the tables. I bought a General/Quebec, which at the time was a product that had seasoned castings. My rule at the time was to buy old world quality in both table saws, and jointers, any precision tools, other stuff it sometimes doesn't mater. I am not discounting that you will get good quality from Grizz, but measure twice, buy once

Re: jointer

#7

I thought Bridgewood went out of business in 2008?

Dick Coers

Are you talking about a new machine? I'm confused.

Re: jointer

#8

Re: I thought Bridgewood went out of business in 2

Dave Nichols

I had the 6" Bridgewood, never had a problem with it but gave it to my son when I upgraded to an 8" Grizzly. The Bridgewood was imported by Wilke Machinery in York, they no longer have that line of tools according to their website.

Re: jointer

#9

Re: Believe you are correct

Larry Clinton At Frankfort, (Central) Indiana

I think the Bridgewood was "discontinued" and replaced with the Yorkcraft line (probably just a name change). As to Wilke Machinery Products, I am somewhat dissatisfied with them. I purchased a 20" Yorkcraft Planer with a Byrd head from them 7 or 8 years ago. As I recall the cost at that time was around $2500. After a 3~4 week wait, I was informed the Byrd Head was on back order, so they shipped it with the standard head - and said they would ship the Byrd head when it arrived. They did ship it a few weeks later and my son and I installed it, the old head is still in the shipping crate under a table (coated with a rust preventative). About a year and a half after receiving the unit the paint begin cracking and falling off the cast iron base (above the motor housing. It is apparent the cast was not properly cleaned when painted as it all came loose. I called Wilke to obtain the same color paint, and they told me they could not send any paint (even if I paid for it). Still haven't repainted the part, guess I will have to have a paint match made at the local auto paint store. Sure it will cost me a $100 or so to obtain the proper paint!

Re: jointer

#10

$100 for a quart of paint?

Dick Coers

Does your store charge for a color match or something? If that's the only trouble you had Larry, sounds like you got a good machine. Taiwan and China have never been known for detail quality.

Re: jointer

#11

Re: $100 for a quart of paint?

Larry Clinton At Frankfort, (Central) Indiana

Well I am just going by past experience, I have a Powermatic 90 lathe I purchased after a local school disbanded their shop program. I rebuilt the lathe and decided to repaint it due to many scratches and stains. I purchased a quart of matching paint, the retarder and thinner from the local Automotive paint supplier to body shops. Total cost 7~8 years ago was between $50 ~ $75. I figured it has probably gone up by now, and as I will have to remove all the existing finish (cracking and peeling to base metal) I would not repaint without applying a good primer - doubt I can purchase the paint and primer for much less than $100.