Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Question on large wood slabs

Posts

Re: Question on large wood slabs

#26

You'd Lose

Mark Mandell - Gone Round In New Jersey

that bet.

a) not a wall (that's one of the house furnaces) and a dead stack of 5/4 walnut to the right

b) the stack was shuffled (and pieces rotated) twice a month for the 1st 6 months

c) 20" box fan used every 3rd day for 6-8 hours during the 1st 6 months along with a 70pt/day dehumidifier from April through October

[Simmy Agin taught me well]

It's all 9% which matches the framing lumber in the house

;)

Re: Question on large wood slabs

#27

Then why don't they do the marketing?

Dick Coers

Can you give us a list of the mills near you who sell book matched kiln dried slabs?

Re: Question on large wood slabs

#28

Re: 090 Stihl, the king of the woods!

Tom in Toronto




I have put these up here before. It shows some of the milling of the beech for planes, I guess the first cut.

090 Stihl, 026 for felling and crosscuts. The stick on the lift looks small but it is good 4 inches thick. I bought this saw around 1989, maybe. The pics are from about 3 years ago. The guys who set the mill up for me had their own way of rigging it. They drilled and tapped the bar, and the jig, so that it attaches to the machine with two bolts, not the clamp arrangement. It has proven a very effective method. I added the handlebar foam to kill vibe, I still wear two sets of gloves. I also took off the hand eating T-nuts, and replaced them with rod connectors, and I use a socket wrench to make adjustments, and I don't lay into the nuts. It will lock up tight the moment the washers flatten out, if any of that makes sense.

I normally use plywood and a drill driver to set the ends. But I have just switched to the Malloff method where that board has angle irons under it, and it sits on top of bolts. One sets the plywood, then one strings a line and sets lags every so often, and these allow the plank to be moved along as far as one wants, and one can keep cutting without stopping. One can cut a hundred foot plank if one wants to.

I also got a spare side cover for the 090. I sawed all but the plates away, this is said to reduce clogging from shavings which are long shaving, almost like a string. The saw is designed to crosscut, and the regular escapement is fine for dust.

I had the original chain modified to a ripping format, but the squaring off was only done about half way across, so that each tooth does half or more of the work. This allows the chains to last a lot longer.

These things are really really noisy, so one thing there is to not wear glasses. I guess I should wear a shield, and that would protect my eyes and nostrils better. If you wear glasses and can't find those little arm pillows, it will let a lot of sound in around the frames.

Re: Question on large wood slabs

#29

No Pics

Mark Mandell - Gone Round In New Jersey

You have to register to post pics here, Tom. Try again?

Re: Question on large wood slabs

#30

Re: Not worthy!

Tom in Toronto

You have taken this to the next level. Or to the penthouse. Massive!

Re: Question on large wood slabs

#31

Re: No Pics

Tom in Toronto

I do it all the time without registering, but I have to host them on FLickr. Which I can no longer figure out. That new chick over at Yahoo is making their products incomprehensible one by one.

I thought they would come in from the other place I have them up which is here:

http://forum.canadianwoodworking.com/showthread.php?55062-Homemade-sawmill&p=513511#post513511

The homemade part obviously not referring to me...

Re: Question on large wood slabs

#32

Re: Hey Brian, Thanks for checking in here and

Logs To Lumber

Kieth,

For the amount I knew I would use this I didn't want to take up one whole side of my barn with a track system and also the extra cost with a track system which is hard to keep tight. Also, big logs over 10 feet are in the 5+ ton weight so hard to move around. I can only power a 7 1/2 with my phase converter.

The 5 grand to change out the motor, wiring and new phase converter for a 15hp isn't on my radar now.

I would like to see what it would run like with a 15.

I get my logs from local tree services.

I designed the mill and had a fab shop weld the frame and misc. parts. There is no machining on the mill, all fabricated. I'm a machine designer by trade.

Re: Question on large wood slabs

#33

No, he just runs electrical wires through it


Re: Question on large wood slabs

#34

More rigamoroll

Barry Irby

I tried to go to your link to look at the pics, but it objected and said I did not have permission. I spent about two seconds on it, but I am too old and irascible to figure this mess out.

Re: Question on large wood slabs

#35

Jim in Burlington Ont.

Register at CWW Forum

Jim in River Oaks, Ont.

You need to log into CWW to see the images, like WC, CWW requires members to Login to participate and see images etc, it's as simple as becoming a member.. I've been a member there since 1997.

Take care,

Jim

Re: Question on large wood slabs

#36

Ellis Walentine

Correction, Jim

Ellis Walentine

WoodCentral doesn't require anyone to register in order to post messages or view photos. If you want to upload photos from your own computer, though, you do need to have a registered profile.

Also, I currently limit the file size of photos to 100Kb, although these days, with ever-increasing bandwidth, I suspect that fewer of our visitors would mind downloading photos of 200 Kb or more. Let me think on this...

Cheers,

Ellis

Re: Question on large wood slabs

#37

What/who is Logs to Lumber/

Barry Irby

Is it a Franchise? There used to be somebody here (Richmond, VA area) that used that name, but I think they are gone now. Is it a common name or are all the various ones related.

Re: Question on large wood slabs

#38

Re: To Be Honest

mark valsi

Mark,

I really like that project !

Re: Question on large wood slabs

#39

Re: Correction, Jim

Tom in Toronto

Can anyone else see my photos? They show up fine on my computer, but maybe that is for some reason like I was logged onto the site that is hosting them now.

Yeah, you don't need to log in here to post. Which quite possibly WC this place as the last civilized public place on earth. +1.

Which raises the obvious question of what you were thinking when you name the place WC?

Re: Question on large wood slabs

#40

Thanks

Mark Mandell - Gone Round In New Jersey

Memsahib does as well. :)

Re: Question on large wood slabs

#41

Re: To Be Honest

Howard Norman

I like the table.

Re: Question on large wood slabs

#42

Re: Eror 404!

Tom in Toronto

I was looking around one of those wood sites. There was a guy looking for some 404 ripping chain for his mill. Medium panic, then he finds what he needs and buys 3 rolls of 100 feet! Man I am so deep in the woods with just the two original chains I got with the mill, and haven't even sharpened (that day has come). I can't imagine all the wood I would have to saw to get to 300 feet of chain.

Re: Question on large wood slabs

#43

Maybe he's cutting reallllllly big logs


Re: Question on large wood slabs

#44

Thanks, Howard

Mark Mandell - Gone Round In New Jersey

It was fun to do, although the design and research phase took longer than I expected.

Re: Question on large wood slabs

#45

Re: No Pics - maybe this time...

Tom in Toronto




Re: Question on large wood slabs

#46

I like the bench....

Basil

...the young girl is sitting on. Simple, sturdy, wide, long and no legs to come loose or break off. What kind of finish are you going to use on it?

Re: Question on large wood slabs

#47

Re: I like the bench....

Tom in Toronto

That's my wife, she is 52. You sure know how to talk to the ladies...