Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Your Best finish for Birds Eye maple eau natural

Posts

Your Best finish for Birds Eye maple eau natural

#1

Your Best finish for Birds Eye maple eau natural

Mark

What is your finish recommendation for accentuating birds eye maple while maintaining most of the blonde natural look of the wood? I don' t mind going a little golden, but of course want to see the Birds eye pop a bit without darkening the wood too much.

Thanks

Mark

Re: Your Best finish for Birds Eye maple eau natural

#2

Re: Your Best finish for Birds Eye maple eau natur

don stephan

You might try several coats of blond shellac on some scrap.

Re: Your Best finish for Birds Eye maple eau natural

#3

Re: Your Best finish for Birds Eye maple eau natur *LINK*

Rick Christopherson

For a wood like birds eye maple, what you want to do is accentuate the natural Chatoyance. To accomplish this, a glossy finish is best, regardless of the type of finish you choose.


http://en.wikipedia.org/wiki/Chatoyancy

Re: Your Best finish for Birds Eye maple eau natural

#4

Michael Donaldson

Blonde Shellac

Michael Donaldson

I love figured maple, and have gotten the best result with shellac, it really makes the figure pop better than any other finish I've tried. I use a 1# cut and put on 10-15 coats.

Re: Your Best finish for Birds Eye maple eau natural

#5

getting shellac to build in fewer steps

Bill Tindall, E.Tn.

Some of the ways to apply shellac require a highly thinned formulation to achieve a smooth coating. It takes many coats of the thinned material to build a sufficiently thick coat on the wood. The impatient may avoid shellac for this reason.

If you have the means of applying less thinned shellac (2 or 3 pound per gallon) and keep the coating smooth you can get to the same end quicker. Spraying the shellac is one way. For objects mounted in a lathe the shellac can be applied from a piece of upholstery form (any of the white or green kind) or a fine haired brush that will hold a lot of material. Some foam brushes can be successfully used on a flat surface with unthined shellac . (some black foam brushes disintegrate in alcohol) There may be other means.

A successful way to "cheat" French Polish is to spray a thick coating and then polish it out conventionally.

Re: Your Best finish for Birds Eye maple eau natural

#6

Re: Blonde Shellac

don stephan

Bill has some good suggestions. Another is to brush a thicker coat of shellac and after it dries gently scrape any drips or runs with a razor blade and level sand as needed, to build thickness, then finish with one or two thin coats for a perfect surface.

Re: Your Best finish for Birds Eye maple eau natural

#7

Re: Guitar makers...

Tom

Often used horrid stuff like epoxy of super glue to build the base. In fact, one can pretty much FP super glue, the technique isn't exactly the same, but it is similar.

The problem with globing on a lot of spray or other stuff is that the material is not the same, and the layers aren't there. If one big fat layer was better, it would save a lot of time at the Ferrari factory, Shellac is not the stuff in the bottle, it is the dried on form on the product, so to speak. The thinner stuff is a different deposition than the thicker stuff, it would not look the same under electron microscope. Actuall, if I had had to guess, I would have thought the thicker would be better with fewer blow holes from escaping gases. Anywho...

Another method to quick build FP is to use a random orbital sander. This was explained in an FWW article. I haven't tried it. But basically you buit a fad for the ROS, and powered the stuff on. I didn't try it, because on the stuff I do, the corners are the trick, not the flats.

Whatever you do, don't be like the guitar couple who are rightly well known, and known for their FP work, and then it came out it was mostly 5 min or Cyano. They weren't doing anything bad in their minds, I am sure, sythetic bases are common on many guitar finishes, but heck, if we knew it was mostly epoxy, we wouldn't have been in awe. If you are taking shortcuts (though some as Bill points out are standard), don't pretend you are polishing.