Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

Slow setting glue questions.

Posts

Slow setting glue questions.

#1

Slow setting glue questions.

Barry Irby

I am assembling a chest of drawers that involves some long sliding dovetails. They are a little looser than I would like so I was thinking of using epoxy because of its gap filling abilities. (I can move the pieces about 1 or 2 hundredths of an inch once they are slid home) The problem is I have run out of slow setting epoxy. They don't have it at the local Borgs. They do have the 5 minute kind. Not sure I can get it mixed, the joints coated and assembled and properly squared up in five minutes. I could order some, but that puts the process on hold for several days.

Is there anyway to slow down epoxy?

What about Old Brown Glue? I have some.

I also have Titebond.

Re: Slow setting glue questions.

#2

Re: Slow setting glue questions.

Bill Tindall, E.Tn.

There is so much gluing surface in a sliding dovetail that I would simply go with yellow glue and not worry about the loose fit. In fact, if it is not loose you won't get it together with yellow glue.

BTW, where in a chest of drawers is a sliding dovetail required/desirable?

Re: Slow setting glue questions.

#3

Tightbond 3 is the slowest. *LINK*

Keith Newton

Not as slow or as good a lubricant as epoxy, but then you might have to wait.

I thought there would be a West Marine store where you are. And for some reason, I thought the big box stores were offering epoxy in 2 quart sizes.

I order my epoxy from the link below. The price beats any others that I know of, and the 1-1 ratio is very forgiving. I have four gallons on the way right now.


http://FGCI.com

Re: Slow setting glue questions.

#4

Re: Slow setting glue questions.

Barry Irby

Bill, I have lost my mind. (my son won't even discuss woodworking with me because he says I am going to find he hardest way possible anyway.) I made the chest out of the wood form a single log trying to keep the wood matching. The sides are glued up as is the top. I used sliding dovetails to join the sides to the top. Just seemed like a good idea. I usually taper them so that they tighten up as they close, but I forgot.

Re: Slow setting glue questions.

#5

Re: Slow setting glue questions.

Dick Coers

.02" of movement? That's a lot! More than a 64th. With that kind of gap you may also want to add some filler to the epoxy. If you cool the epoxy, it will set slower. You may also want to glue on a piece of veneer and recut.

Re: Slow setting glue questions.

#6

craigd

Try the hobby store

craigd

I get my 30 minute from the hobby store.

Re: Slow setting glue questions.

#7

Re: Slow setting glue questions.

William Duffield

Everyone else has mentioned what you should do, but without answering yur question. No, do not use 5 minute epoxy. It will kick and the joints will freeze up before you are finished assembly, and will not give you a second chance.

The problem with non-tapered sliding dovetails and any water-based glue is that it is very difficult to predict how much the joint will swell up and stick before assembly is complete. One strategy that has a better chance of working is to mostly assemble the joint and then put glue on the back end of the tail and the front end of the slot and immediately close the joint with a prepositioned clamp. Of course, this doesn't provide a full length glued joint, which might be important if your joinery is looser than optimum.

I don't know where you live, but as Keith asked, isn't there a West Marine or a Woodcraft or a Rockler near you?

Re: Slow setting glue questions.

#8

Re: Slow setting glue questions.

Larry in NW Ohio

I just thought of something when I read Williams post just above mine here. One trick I did a few times when I didn`t have enough time to clamp a joint and the glue would set up befor I had it clamped where I wanted it. I would put the yellow glue on about 1/2 to 3/4 of the joint and the rest I would put epoxy or something else that would set up a little sooner but give me time to get it clamped where I would want it. It seemed to work because the cabinet is still in use after about 4o years. Good luck. Larry

Re: Slow setting glue questions.

#9

Re: Slow setting glue questions.

gary peterson

I agree with the person who mentioned the 64in gap(my apologies for not remembering name). I would place a shim shaving on one side of your dt,( on the same side of each dt that is since there is more than one.)..try dry fit, when satisfied, then glue front and back as described by others..joint should be tight. shim should have glue each side. Should be some shavings on your floor, or get out the plane. good luck