Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Frank Klausz/Ellis workbench

Posts

Frank Klausz/Ellis workbench

#1

Frank Klausz/Ellis workbench

warren parchan

Hello Ellis or Fran,

Well I'm new to your web site and late getting this question off. I hope you can help back in 2004 there was an article in the woodworker's journal that I think you wrote about Frank Klausz's European workbench. I am in the middle of building one of these great benches but have found that now (due to the late start) can not find the two vise hardware shown in the article but no sources. As you are aware the whole side of the table is designed around the vise which I need so I can finish this part. I am sure I will have plenty of questions later but at this time my base and most of top are complete and need this important hardware. Please let me know your thoughts and comments asap.

Your site is great and will now be able to use it's benifits.

Thanks Warren

Re: Frank Klausz/Ellis workbench

#2

Re: Frank Klausz/Ellis workbench

BrianMonumentCO

IRC that would be the same bench as seen in Taunton Presses The Workbench Book.

I one upon a time bought the vise material to build a bench similar to Klausz bench.

It think I found the stuff at Woodcraft.

At that time, garrett wade had some stuff as well. Don't think so now.

Re: Frank Klausz/Ellis workbench

#3

Ellis Walentine

Woodcraft used to carry those screws

Ellis Walentine

Check with them and see. If they no longer carry them, see if they have a current source. I can dig into this if need be. Frank and I had a lot of fun on that project.

Ellis


Re: Frank Klausz/Ellis workbench

#4

Re: Frank Klausz/Ellis workbench

Dick Coers

Here's my version, built from the Workbench Book. Probably getting close to 30 years old now. Red oak and walnut. Pic was taken 20 years ago, but it's still going strong.


Re: Frank Klausz/Ellis workbench

#5

Warren try this link

BrianMonumentCO

Fine-Tools Vise Hardware

about 5 items down....

Re: Frank Klausz/Ellis workbench

#6

Re: Frank Klausz/Ellis workbench

roger lance

Warren.....there is sort of a rule to have your hardware in hand before starting your project....LV sells both a shoulder vise screw and a tail vise screw.....and with luck, they may fit what you have already made....good luck.

Re: Frank Klausz/Ellis workbench

#7

Re: Woodcraft used to carry those screws

Keith Newton

Hey Ellis, I'm guessing this was taken before the fire I've heard mentioned. Was it destroyed in the fire?

Re: Frank Klausz/Ellis workbench

#8

Woodcraft or Lee Valley...

John in NM

Both sites show the same or similar hardware to what's used in the article.

Re: Frank Klausz/Ellis workbench

#9

Am I the only person that sits at a bench?

Bill Tindall, E.Tn.

My bench is open below like a table with a shelf. I often sit at it on a stool and put my feet on the shelf, especially when doing a tedious task like chopping waste from dovetails and the like. (the shelf is a disorderly accumulation of electric powered hand tools) . Many bench designs have cabinets below. That would put this storage handy but I suppose prevent sitting at the bench? But maybe sitting at a bench is uncommon?

Re: Frank Klausz/Ellis workbench

#10

Ellis Walentine

Post fire

Ellis Walentine

My shop burned to the ground in May 1999. Frank and I built those five benches at his shop in 2004 for the Woodworker's Journal article.

Frank was among my pals who showed up to help frame the new shop.


Re: Frank Klausz/Ellis workbench

#11

That's why the right side is cantilevered 

Dick Coers

I kept the cabinet section short so I could sit and work on the right side. I clamp my dovetail fixture to the right side with bench dogs so I can sit and work there. That tail vise fits well and is flush with the top, Works great! I also made a small separate bench that was featured in Woodworkers Journal, Jul-Aug 1997. It has a small face vise and bench dogs. It gives me the flexibility to move it around the shop, or because it's the same height as my main bench, it works a bit like a sawhorse.

Re: Frank Klausz/Ellis workbench

#12

I didn't know you wrote for Woodworkers Journal

Dick Coers

How much did you do for them Ellis? I worked there when they were based in Peoria. Then latter I did two projects for them when Rockler bought the subscription list and title quite a few years ago. I made a little remark online about the general degrading of the woodworking magazines of the day, and that was the end of that. Truth hurts I guess. I don't ever see anyone saying they learned a woodworking career from a magazine these days. It was a very common remark made when Fine Woodworking, American Woodworker, and maybe just a little from Woodworkers Journal when they were in their prime. My work is an example of being rooted in that magazine education.

Re: Frank Klausz/Ellis workbench

#14

Depends

John in NM

I sit at the bench a lot of the time, I have an old draftsman's chair that is tall and has a foot ring like a bar stool.

When hand planing or using the rasp aggressively, I have to stand. The bench I've never finished (yet! :D ) is designed to have many drawers below. Looking forward to both the ballast and being able to get rid of my chest toolbox.

Re: Frank Klausz/Ellis workbench

#15

question

Bill Tindall, E.Tn.

I like the auxiliary bench/saw-horse-with-a-vise idea. How big is the top? Does it seem top heavy/tippy?

Re: Frank Klausz/Ellis workbench

#16

Re: Frank Klausz/Ellis workbench

Hank Knight

Warren,

My father planned to build a Klaus bench from the Landis Workbench Book back in the 1980s. He bought heavy duty German screws for both the shoulder vise and the end vise. He died before he started the project. I still have the hardware. I think it still has the tags on it. I will never use and I would be willing to part with it if you're interested. If so, email me with any questions at: hankknight@msn.com.

Re: Frank Klausz/Ellis workbench

#17

Re: question

Dick Coers

The top is 14.5"x28"x 36" tall. The foot piece on the trestle leg is 18" long, so 3.5" wider than the top. It's not tippy at all.

Re: Frank Klausz/Ellis workbench

#18

Re: What is Frank doing now days?

William Duffield

Frank recently retired, and (IIRC) sold his shop to his "journeymen". He still goes in and builds things, but only what he wants to build. This summer, members of CJWA enjoyed an all day seminar he presented for us.

Re: Frank Klausz/Ellis workbench

#19

Ellis Walentine

I was a "frequent contributor"

Ellis Walentine

I have a long history with Larry and Rob, and I've done a few things with them over the years. The Klausz workbench article was a 24-page bind-in, so I had a big platform for that article. I'm going to decline the temptation to hold forth on magaznes and woodworking education. I could write a book about it. Maybe before I retire...

Ellis