Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

100+ Wood Species + Full-Shop Services: Lumber, Veneer, Tools & CNC. Everything in One Place.

DeWalt 733 Fixed

Posts

DeWalt 733 Fixed

#1

DeWalt 733 Fixed

Stuart Johnson

I finally got time to install a new busing. You can see the old one is cracked and worn into an oval.


I only installed the one but will probably do the other three when I get time. I did have a couple problems.

1. There is a rather stout spring pushing the bushing (57) into the holding bracket (56).

2. The room to get a screwdriver onto the screws is limited even with the head cranked up as high as possible..

Between 1 and 2 I managed to strip both screws and had to grind them off. Not hard but a pain. I hate Phillips screws.

The springs in number 1 can be overcome with a bit of pressure with a clamp.

I ended up buy a set of sprockets, not needed and four bushings. So all in all it was not an expensive fix.

One last issue was my own doing and a slap the forehead when fixed. In trying to get enough room to get to the screws I cranked the head up as far as it would go. The yellow sides and top were removed as a unit and would not go back on. I spent a half hour trying to figure why when finally the light bulb when on and I lowered the head.

Re: DeWalt 733 Fixed

#2

Ellis Walentine

Thanks, Stuart

Ellis Walentine

I wonder how many other DW733 planers have the same problems. Thanks for sharing your fixes and insights.

Ellis

Re: DeWalt 733 Fixed

#3

Re: Thanks, Stuart

Joanne in Point Pleasant, PA

Eek! I hope not mine! I just put on new blades yesterday and found a loose screw on a roller, that I think accounted for mine having poor performance. I am heading out to test it and get some work done on Mom's sideboard before I leave for NYC.

Re: DeWalt 733 Fixed

#4

Re: Thanks, Stuart

Barry Irby

I thank you too. We were posting back and forth about this. I ordered the chains, but I have to admit I was doubtful they were the problem. I am a little put out that they have not come. I chose the budget shipping and apparently they shipped them by DHL. DHL is so rare around here that it took me a while to remember who they were.

I will order the bushings today. I hope they will ship them tomorrow. What other parts would you recommend?

Re: DeWalt 733 Fixed

#5

Questions Stuart?

Barry Irby

What do you mean you had to grind off a couple of screws? How did you get them out to replace them after grinding them off?

How long did it take them to ship the parts? The site indicates 9 to 13 days and Christmas is coming.

What other parts do I need to order?

Re: DeWalt 733 Fixed

#6

Re: Questions Stuart?

Stuart Johnson

What do you mean you had to grind off a couple of screws? How did you get them out to replace them after grinding them off?

I ground the head down just to the point where the hole / shank were just starting to show. I bit of pressure behind the bracket allowed them to pop off leaving about 3/8'' or less of the screw shank. I don't know if the grinding loosened it or what but both turned out with very little finger pressure. With the proper length screwdriver, a clamp pulling the roller and bushing back you might not have stripping problem. I have a knack for stripping screws just by looking at them.

How long did it take them to ship the parts? The site indicates 9 to 13 days and Christmas is coming.

Four or five days. Have the chains been shipped? If not you might want to cancel the order and just go with the bushings. At this point I don't see how either the chain or sprockets can really get much wear. But, I also don't know how the bushing wore and broke the way it did.

What other parts do I need to order?

If your issue is the same as mine you won't need anything else. I would not purchase any screws. For whatever reason the ones showing as the correct part were too large. I bought new ones at ACE Hardware.

Re: DeWalt 733 Fixed

#7

Re: Thanks, Stuart

Stuart Johnson

I just put on new blades yesterday and found a loose screw on a roller

Finding loose screws laying about is sort of scary. I found a large nut inside my tablesaw and have never found where it's from. I have visions of the motor and blade flying through the shop someday.

Re: DeWalt 733 Fixed

#8

Thank you for taking the time to answer

Barry Irby

I have some heavy work coming up for my planer and I don't want to do it before I fix it. OTOH I don't want to tear it apart and wait for parts. I planed a couple of 2" wide strips and the machine jumped a couple of times. I sanded the strips, but I don't want to do any more damage to the machine.