Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Chair leg/floor protectors questions

Posts

Chair leg/floor protectors questions

#1

Chair leg/floor protectors questions

Barry Irby

I just refinished the oak flooring in my dining room. Used Varathane oil based urethane. What would you use on the bottoms of the chair legs to protect the floor? They came with some sort of nailed on felt things that failed leaving the nail behind that gouge the heck out of the floor. I now have the hard plastic ones on them. Some one suggested ones that have a metal circle with a cup on them you drive into the leg leaving some felt exposed. So what would you use?

Re: Chair leg/floor protectors questions

#2

Re: Chair leg/floor protectors questions

John Veerkamp

I have used lots of different kinds, including those felt ones with the metal circle that drives into the leg. I still prefer the nylon ones with a nail that drives into the leg. Just check them periodically to make sure they are still sound. A set should last 5 years or more depending on your usage. I have some 10 yrs with no visible wear.

Re: Chair leg/floor protectors questions

#3

Re: Chair leg/floor protectors questions

paul in AZ

I have in the past used the slip on rubber protectors. They work reasonably well and are easy to replace when they wear out. That assumes you can get a size that fits the leg end snugly.

Nylon glides with the drive-in nail are better. One complaint is that glides small enough to fit a chair leg usually come with a nail that is too short to be stable. I still like these on furniture that is rarely moved.

Now, unless it is a very hard use area I don't bother with anything.

Re: Chair leg/floor protectors questions

#4

Re: Chair leg/floor protectors questions

Pat Riley

I have tried most of the available options.

These days I just periodically use a random orbit sander and sand the bottoms of the chair legs with 220 then 320 grit. It basically polishes them. Dust bunnies don't stick and they don't mar the floor. Now that the kids are older and they get wet less often sometimes I only do it once a year.

Re: Chair leg/floor protectors questions

#5

Jack Guzman from Maine

Re: Chair leg/floor protectors questions

Jack Guzman from Maine

I use the glue-on felt ones. No nails please. I really hate driving nails into chair legs.It makes a hole and after a few replacements the bottom of the leg starts to come apart.---Jack

Re: Chair leg/floor protectors questions

#6

Same here

Tony-Memphis

The adhesive on the stick on kind seems to be pretty tough. Mine have lasted many years. I swap them out as needed.

Tony

Re: Chair leg/floor protectors questions

#7

Re: Chair leg/floor protectors questions *LINK*

Lee Schierer in McKean, PA

I found some at Home Depot that had a teflon slide surface. They are gray in color with a black backer that screw onto the chair leg. They are called magic sliders. They work quite well and don't scratch the floor.

Lee


Magic Slider

Re: Chair leg/floor protectors questions

#8

Same here II

Bruce, a MN Galoot

We had used the nail-on nylon ones, but didn't care much because the flooring was vinyl. Now with a solid oak floor I want no scratches. If they come off I'll glue on new ones.

Re: Chair leg/floor protectors questions

#9

Re: Chair leg/floor protectors questions

Larry in NW Ohio

Barry I took a look at what Lee posted and they look very pleasing. I might try them the next time I need some, but instead of the nail , screw or stick on, I might try and use epoxy glue and see if that might work. Or just go to a few stores that have them and just see what might work for you, and maybe usr glue to put them on and stay away from the metal fastener. If glue fails it should not mare the floor. Good Luck Barry, and let us know what you come up with. Larry