Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

Desk is done at last

Posts

Desk is done at last

#1

Desk is done at last

Bill Tindall, E.Tn.





Wood is curly ash. Banding is African Blackwood. Finish is Target 9000 med rub urethane which is not supposed to yellow....I hope! It has a bit more shine than I desire and I am pondering how to dull it some. No experience with waterborne. I'd wool and wax it if it was lacquer or varnish.

Still pondering pulls. Would like to make them of BlackWood but can't vision a shape I could make. May use black oiled bronze/brass, something modern if I can find it.

Next project is a plain walnut chest of drawers for granddaughter #2. Cock beaded drawers with crotch walnut drawer fronts. I'll find something nice for sides and top too.

Re: Desk is done at last

#3

Jim DeLaney, Austintown, Ohio

Re: Desk is done at last

Jim DeLaney, Austintown, Ohio

I've cut the gloss down on Target waterbornes using the "Mirkalon" abrasive wools. The red cuts pretty fast, but the gray or brown work well.

Wax afterward.

Re: Desk is done at last

#4

Really, really nice work, Bill!


Re: Desk is done at last

#5

question

Bill Tindall, E.Tn.

not familiar with this product. Where do I learn about it and buy some?

Re: Desk is done at last

#6

Synthetic Wool

Mark Mandell - Gone Round In New Jersey

"no brand" sold in 8x10 pads in good paint stores (not the borgs). Green, Maroon, Gray, and White. Don't go to the white if you plan on recoating (adhesion issues reported). Gray's about the same as 4-0 wool.

Good stuff.

Re: Desk is done at last

#7

Jim DeLaney, Austintown, Ohio

Re: question *LINK*

Jim DeLaney, Austintown, Ohio

My mistake on the naming - it's "Mirlon" and it's made/sold by Mirka.

Comes in maroon (360 equiv) gray (1500 equiv) and gold (2500 equiv).

I usually rub LIGHTLY(!) with the maroon, then go to the gray to give a nice matte finish. Then some wax to bring back a little lustre.


Mirlon (in second row)

Re: Desk is done at last

#8

Jim DeLaney, Austintown, Ohio

Addendum

Jim DeLaney, Austintown, Ohio

Mirlon is NOT the same as Scotchbrite. It's a much softer texture, and feels more like real steel wool than the other synthetics.

The website shows 15~25 quantities, but Hartville Hardware has it in three packs. More expensive per unit that way, though.

Re: Desk is done at last

#9

From synthetic sheep?


Re: Desk is done at last

#10

thanks

Bill Tindall, E.Tn.

I use the 3M grey and buy it by the roll but it is too coarse for the task at hand. In my hands it cuts like O steel wool or about 600 grit paper. Too coarse a scratch for a final surface.

Re: Desk is done at last

#11

Re: Desk is done at last

Jack Plane

Very nicely executed. That truly is a pale finish; at first sight, I assumed the table was still in-the-white.

Re: Desk is done at last

#12

Re: Desk is done at last

Joe in a Cleveland suburb

Looks great, and thanks for all the updates as you were building it.

"Next project is a plain walnut chest of drawers for granddaughter #2. Cock beaded drawers with crotch walnut drawer fronts. I'll find something nice for sides and top too."

I hope you let us watch you build this one too.

Re: Desk is done at last

#13

Beautiful !!!


Re: Desk is done at last

#14

Dale Lenz

Re: Desk Pulls

Dale Lenz

I like your thought of using blackwood for the pulls, no idea of the design. Myself and others wait until the project is near completion until we think about pulls. Have always liked Richard Jones idea of giving his students instructions to design pulls first, then design the project around the pulls, designing backwards if you will.

Very nice looking desk, like the curved stretchers the best.

Re: Desk is done at last

#15

Re: Desk Pulls

Sgian Dubh

"Have always liked Richard Jones idea of giving his students instructions to design pulls first, then design the project around the pulls, designing backwards if you will."

Interesting that you picked up on that Dale, but my guidance to the student designers I think has a slightly different inference to your interpretation or summary of the intent. It's less about designing around the pulls or handles, and I say it to people so that the whole piece is considered, and hopefully resolved satisfactorily at the design stage, including the handles or pulls. It's sometimes obvious that pulls are an afterthought, and because of that they can spoil the piece.

I suspect you understand that perfectly well already, but I'm not sure your wording conveyed your understanding as well as it could.

As to Bill's challenge, there are clues in the form. There are straight lines, rectilinear (boxy) forms, and sweeps. He can pick up on these clues and pick (or perhaps make) something to either contrast or complement them. He can also pick up on the colours-- off white and black, and somehow reflect this element. I rather like the idea of no pulls at all, but the trick is then how to open the drawers. If the piece lacks a dustboard some sort of drawer opening device could be fashioned that fits under the drawer bottom, perhaps attached to the back face of the drawer front. Open the drawer part way using this device and then put fingers inside the drawer from the top of the drawer front and open it as far as needed. Slainte.

Re: Desk is done at last

#16

Re: Desk is done at last

Joseph Mulherin, sr

Bill, my suggestion for the desk pulls: use the design of the stretchers, but reverse the front and back so you have an elliptical pull and put a blackwood block on each end to screw the pulls to the drawer from the rear. Blackwood all around.

Re: Desk is done at last

#17

Re: Desk is done at last

Paul Leuba

Super piece, Bill! Congratulations.

One question: How did you achieve stability on the legs where they attach to the top. It looks like the drawer is very close to the top of the leg eliminating the possibility of a sizable mortise and tenon joint. What is you secret on this one?

Pau in Hunt Valley, MD

Re: Desk is done at last

#18

Dale Lenz

Re: Desk Pulls

Dale Lenz

No agrument from me, :).....Sounded good to me. Thanks anyway....Before you said that many years ago I had a custom 5 drawer file cabinet to build. The lady wanted the drawers large enough to file legal size documents, 8.5" X 14" ? I built the drawers first as not to need to modifly their size in case I messed up building the file cabinet. Some woodworkers thought the backward method was nuts! Anyway, it worked for me. BTW, still had the pull issues near the end.

Re: Desk is done at last

#19

Stunning work, as always

John in NM

Bill, I never know whether to be more impressed with your results or your prolificacy :D Either way, the pictures you post never cease to impress!

Looks to me like you hit the leg shape just right.

Re: Desk is done at last

#21

leg joinery

Bill Tindall, E.Tn.


The top rail is dovetailed.


The bottom rail is double tenoned. But I was worried about what seemed to be a frail leg situation. So I additionally inlet the side and back panels into the leg with short tenons. Then I added the stretchers, making one curved so that it stayed out of the way of one's feet, yet spread the effect forward on the legs.

it seems plenty stiff.

Re: Desk is done at last

#22

Leg joinery - Ingenious


Re: Desk is done at last

#23

Re: Desk is done at last

clay foster

Bill, you do nice work. I bet even George Nakashima would like it. :)

Re: Desk is done at last

#24

We would share one thing in common

Bill Tindall, E.Tn.

Part of the ash was sawed in the early 70's at a mill where I helped out. I bought a load of ash logs that came it. I may or may not have sawed it, can't remember. The curly ash was sawed for me in 1991 from some logs I picked off the log yard that were harvested not far from where I now live. Other logs with irregular "star" pattern heartwood were picked for kitchen cabinets. The mill owner, Jack Malone, called this pattern "Calico Ash" a term I have never heard repeated. So we share in interest in selecting wood for eventually use and we will both outlive what we have bought.

Re: Desk is done at last

#25

Re: We would share one thing in common

clay foster

I understand. I've made furniture from wood I sawed from logs a few miles from where I lived. I sawed the logs into lumber with just a chainsaw and a chalk line. I air dried them, brought them indoors for a few years, and then milled them into lumber for tables and cabinets. It's very satisfying to have that connection with a tree and the furniture made from it.

We have a big ash tree in the back yard that will be taken down this winter. Death from emerald ash bores. We'll use as much of it as we can.