Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Biggest lathe I've ever seen! *LINK*

Posts

Biggest lathe I've ever seen! *LINK*

#1

Biggest lathe I've ever seen! *LINK*

Tom Dunlap

Variable speed...lots of power...and portable!


Big lathe

Re: Biggest lathe I've ever seen! *LINK*

#2

Re: Biggest lathe I've ever seen!

Larry in nw ohio

WOW I`d like to see the table he intends to put it on. Larry

Re: Biggest lathe I've ever seen! *LINK*

#3

Here is one longer!

Bill Tindall, E.Tn.


It is two Powermatics welded end to end.

Re: Biggest lathe I've ever seen! *LINK*

#4

Kneale Brownson

Re: Here is one longer!

Kneale Brownson


Re: Biggest lathe I've ever seen! *LINK*

#5

Re: germ of an idea

Tom

http://www.youtube.com/watch?v=P4qB6n1cm04

Re: Biggest lathe I've ever seen! *LINK*

#6

Re: Typical biggun

Tom


Somewhere I have pictures of some really big ones. The period around WWI seems to have spawned massive tools. I don't know whether their equivalents are today. Maybe they learned to work with sub assemblies of steel rather than full length castings, or something. Not to mention improvements in ballistics, though those were well underway in light arms by WWI. Today certain effects could be created by a drone with small accurate weapons, that might not have occured with a Big Bertha type gun in the past

http://www.youtube.com/watch?v=epclkzKJvfc

Some lathes after 6 and 9 minutes



Re: Biggest lathe I've ever seen! *LINK*

#7

Re: Rudder job

Tom


This one interested me. When I built my trimaran, the design called for a post that ran through the rudder top to bottom, so it could rotate on a neutral balance point, and so the rudder could have an ideal shape. It required weldments that I didn't have the capacity for at the time, though I do today. I made the whole thing up, only to discover when I got my tiller fittings for the top that they did not fit. I did not realize that the tubing I had bought was pipe and had external dimensions of an unusable size. Much quality stainless stock is pipe, or gun barrels, etc... The project remained unfinished for a good long time, due more to stuff I was doing at the time. By the time I got back to it, I had a lathe that allowed me to turn the tubing to a proper diameter. My set-up was through the headstock, but otherwise similar to the above picture.

Re: Biggest lathe I've ever seen! *LINK*

#8

Re: Here is one longer!

John Lucas

Nick Cook has a new Powermatic 2442 with a bed extension that is longer than that. Don't know the exact dimensions but it takes up the entire wall length of his shop. :)

Re: Biggest lathe I've ever seen! *LINK*

#9

he missed an opportunity

Bill Tindall, E.Tn.

this lathe sat next to his shop for months. Nobody would buy it because nobody could move it. I think the shop that owned it turned porch posts with it.

Re: Biggest lathe I've ever seen! *LINK*

#10

Re: Biggest lathe I've ever seen!

Larry Clinton At Frankfort, (Central) Indiana

Back in the mid 60's I worked at the Youngstown steel mill in the East Chicago, Indiana area. The plant I worked in made "seamless" tubing for Nuclear, Oil well drilling and gas lines etc. There was a railroad siding inside the plant that ran about 1/4 mile. There was a three piece lathe (could have been a couple more "steady rests" in there too) that was placed on the rails when they needed to turn new bars that pushed a plug through the billet at the start of the pipe manufacture. As I recall the power unit was usually only 50 or 60 foot apart with the cutter / traveler unit in between, but could be extended up to a 1/4 mile! When the parts were made the lathe was removed and train cars ran on the track.