Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

Tuning up a table saw...my way

Posts

Tuning up a table saw...my way

#1

Tuning up a table saw...my way

Mark Hennebury

Starting to work on tuning up a 1950's Robinson ZT sliding table saw.

The set-up:

One good saw

Good old Stereo system

Kick-ass albums

Good supply of "Old Speckled hen"

Abrasive powder

Disc grinder

Serious straightedge

Feeler gauges

Commitment to see it through.

First thing for me is to get the table and sliding table flat.

Once i have flat surfaces then i can reference everything from them.

This is really hard dirty work, so i want to get this done first.

The sliding table is about .015" out overall; seems that the thin edge closest the blade is dropped at the front and rear. This part has no ribbing underneath for support, so its not really surprising.

Just means a lot of work to bring the rest of the table down.

So what i am going to do is check for high spots, then grind them away until the entire table is relatively flat, then i will polish the surface.

Traditionally this would be done by hand or power scraping, either way it is just a method of removing metal.

first check with the Straight edge, to get some idea of what is what.

then put abrasive powder and varsol or WD40 on the main table of the saw and flipping the sliding table on to it and lapping it for ten or more minutes. (good workout)

Then remove the sliding table turn it over and check to see where the high spots are, these will be the areas the have been abraded, also check the main table.

Then i grind away the high spots and repeat, many times. constantly checking progress.

This is a lot of thirsty work.












Re: Tuning up a table saw...my way

#2

Mighty impressive

Howard in Toronto

thank you for showing us these photos

but

you're definitely going to have to keep us in the loop re your progress

Howard

Re: Tuning up a table saw...my way

#3

Re: Mighty impressive

Mark Hennebury

Hi Howard,

I will keep you updated, it will be slow going though.

Re: Tuning up a table saw...my way

#4

Re: Tuning up a table saw...my way


Re: Tuning up a table saw...my way

#5

craigd

Images?

craigd

Unfortunately, the Canadian Woodworking forums need a log in before they will let me view the images (I hates vBulletin), are they available else where for viewing?

Thanks, Craig

Re: Tuning up a table saw...my way

#6

I don't understand the question?


Re: Tuning up a table saw...my way

#7

Re: Images...where are they?

Tom Dunlap

I'm using Firefox FWIW...the pics aren't in your post but there is a huge blank spot where I would expect to see them.

Re: Tuning up a table saw...my way

#8

can you see this image

Mark Hennebury


Re: Tuning up a table saw...my way

#9

Re: can you see this image---Yes

Tom Dunlap

Heavy metal!

Re: Tuning up a table saw...my way

#10

okay i will repost all

Mark Hennebury

Starting to work on tuning up a 1950's Robinson ZT sliding table saw.

The set-up:

One good saw

Good old Stereo system

Kick-ass albums

Good supply of "Old Speckled hen"

Abrasive powder

Disc grinder

Serious straightedge

Feeler gauges

Commitment to see it through.

First thing for me is to get the table and sliding table flat.

Once i have flat surfaces then i can reference everything from them.

This is really hard dirty work, so i want to get this done first.

The sliding table is about .015" out overall; seems that the thin edge closest the blade is dropped at the front and rear. This part has no ribbing underneath for support, so its not really surprising.

Just means a lot of work to bring the rest of the table down.

So what i am going to do is check for high spots, then grind them away until the entire table is relatively flat, then i will polish the surface.

Traditionally this would be done by hand or power scraping, either way it is just a method of removing metal.

first check with the Straight edge, to get some idea of what is what.

then put abrasive powder and varsol or WD40 on the main table of the saw and flipping the sliding table on to it and lapping it for ten or more minutes. (good workout)

Then remove the sliding table turn it over and check to see where the high spots are, these will be the areas the have been abraded, also check the main table.

Then i grind away the high spots and repeat, many times. constantly checking progress.

This is a lot of thirsty work.















Re: Tuning up a table saw...my way

#11

can you see the photos this time?


Re: Tuning up a table saw...my way

#12

Re: okay i will repost all

Larry in nw ohio

Yes they are there. Larry

Re: Tuning up a table saw...my way

#13

craigd

Excellent

craigd

I think "serious straight edge" takes the understatement award, that thing is awesome! I don't think I'd have the nads to use a angle grinder to dial in a flat surface.

Question: you do anything to level the machine? Or is it rigid enough not to warp if not on a flat surface?

Re: Tuning up a table saw...my way

#14

Re: Excellent

Mark Hennebury

Yes it is rather a hefty straight edge for sure.

I have put the machine on rubber pads; the machine base is very ridgid as is the main top, so i don't think that there is any way it would distort to anything that i could measure. This is a 2300 lb saw.

The grinder doesn't take off that much metal; i have gone over the top about ten times so far, grinding then lapping with 80 grit powder. I just did light grinding and changed the pattern each time so as not to make ruts. I also lap it in various directions.

I am getting down to the last .005" so I will have to change to some finer more controllable method, maybe just hand stone it. I will see how it goes.

Re: Tuning up a table saw...my way

#15

scraping

Bill Tindall, E.Tn.

Some of the "Hand Tool" people talk of scraping cast iron. Apparently that is the way to removed controlled amounts of metal. I never figured out how to do it. I could never get a shaving to form, but I can see that it would be a good way to level a surface once one figured out how to do it.

Re: Tuning up a table saw...my way

#16

Re: scraping

Bruce, a MN Galoot

on the machinists' forums, they speak of scraping cast iron surfaces to .0001". It's relatively easy to do, but just as easy to muck it up. It leaves an extremely flat surface that can also hold oil, important to moving parts.

Re: Tuning up a table saw...my way

#17

How

Bill Tindall, E.Tn.

I never fashioned a scraper that would engage the metal to take a shaving, or even make dust.

Re: Tuning up a table saw...my way

#18

easy

Bruce, a MN Galoot

if you don't have a dedicated metal scraper, either hardened steel or carbide, simply take an old file, grind the bottom face smooth and then grind a slight (80-85 degrees) bevel on the end at a very slight camber. Hold the handle a bit elevated from what you're working on, and then keeping one hand on the business end, push a bit and you should see slight flakes pop off. Adjust the angle for best results. You'll get the hang of it pretty quickly. It works really well on brass and bronze, too. In the machinist's world, scraping is an art and is taken seriously.

Re: Tuning up a table saw...my way

#19

Re: easy

Larry Clinton At Frankfort, (Central) Indiana

Fairly easy to get shavings - pretty hard to get a "perfect" surface. An old Gentleman at my work - (older than me! retired in his late 70's) in our model shop could take an old worn mill or lathe and scrape the ways - looked like it was machined and was well under a .0001 of flat. He used Prussian blue and a high precision straight edge (used for nothing else). I was an Engineer there for about 40 years - saw him do some amazing things with machinery and hand tools. We had a full tool room with about 20 tool & die makers - doubt any could duplicate his work.

Re: Tuning up a table saw...my way

#20

You're right, scraping needs to be done carefully

Bruce, a MN Galoot

It's easy to make a serviceable scraper, which was Bill's question and most of my response. Learning to do it right is entirely another matter. On the Home Shop Machinist forum I read a response by Forrest Addy, indicating that tolerances in the millionths are achievable by someone who knows what they're doing. I expect it would take a while to reach that level of expertise. :O