Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

Listening to Knuckleheads, Click & Clack,

Posts

Listening to Knuckleheads, Click & Clack,

#1

Listening to Knuckleheads, Click & Clack,

Keith Newton

On their puzzler, they were describing how to use the battery, and wire, to magnetize a screwdriver. Those knuckleheads gave a bad answer, which could be a bit hazardous. They described leaving the wire hooked up, making a electromagnetic. The problem, is a direct short across the battery terminals, will get too hot to hold in seconds, and might blow the battery up.

Back when I was a young carpenter, before all the suppliers had apex bits, and the handy little magnetizers. I would cut the handle off regular + drivers which we magnetized on my truck battery. All you have to do, is wind the wire around the shaft about 6 times, hold one end to one terminal, then drag the other across the top of the other terminal. Sparks will fly, but whatever you do, don't stop, or it will self weld and burn your hands.

I've needed to use this a few times lately when we were away from the shot, and only had new bits. My helper Ben, says he is going to buy one and tie it to me somewhere. A week or two earlier, while wearing some really old jeans with a hole in my pocket, a bit found it's way into my boot. I dint' feel it fall, and only noticed it when it made it under the ball of my foot. We had a frantic pace going, and I complained a bit before stopping. When I did stop, and pulled it out, I said, "Damn, If I'd known it was that, I'd have stopped this morning to take it out."

Ben decided that tying the magnetizer to my boot string would be perfect, since that would be close to where I keep the bits. ha

Re: Listening to Knuckleheads, Click & Clack,

#2

Ellis Walentine

Maybe you should tell them

Ellis Walentine

Sounds like it is worth a note to their website or contact info, Keith. Thanks for the warning.

Ben sounds like a helpful guy. :)

Ellis

Re: Listening to Knuckleheads, Click & Clack,

#3

Re: Listening to Knuckleheads, Click & Clack,

Rick Christopherson

I can't find any information on this puzzler, but depending on what they said, it isn't necessarily wrong. Copper wire is not resistanceless. The size of the wire and the length of the wire determines whether you could leave this magnetizing coil connected to the battery without any problems.

For a 10-amp amperage limit on a 12 volt battery, you only need 1.2 ohms resistance of the coil. If this was 20 gauge wire, this is only about 100 feet of wire. The smaller the wire gauge, the shorter the length needs to be to achieve a high enough resistance to not overload.

In your posting you mentioned using just 6 wraps. Is this what they suggested, or just what you have used in the past?

Re: Listening to Knuckleheads, Click & Clack,

#4

Re: Listening to Knuckleheads, Click & Clack,

Keith Newton

Rick, I kept a single strand of #12, or maybe #10, about 15" long, stripped out of a scrap of romex. I wont pretend to know much about the dynamics, only that it stuck a few times, and was hot before I could jerk it off.

Re: Listening to Knuckleheads, Click & Clack,

#5

Re: Listening to Knuckleheads, Click & Clack,

Rick Christopherson

That's because the resistance of that large of a wire at that short of a length is so low, that the amperage would be high enough for arc welding. A smaller gauge and/or longer length would have enough resistance to not cause this.

An existing solenoid is nothing more than a coil of wire, but its resistance is high enough to limit the amperage through the wire for the given voltage. At 12 volts, it doesn't take very much resistance to limit the amperage to manageable levels.

Re: Listening to Knuckleheads, Click & Clack,

#6

Click & Clack, the tappet brothers.....

roger lance

Don't know about this particular piece of advise, but I do enjoy listening to their show which we get on Sunday mornings....they have a great sense of humor....right down to their legal representatives Dewey, Cheatum, and Howe.

Re: Listening to Knuckleheads, Click & Clack,

#7

try the cartoon DVD..

Bill Tindall, E.TN.

It will leave your sides aching from the laughs. No sacred cow is spared. I think you can rent from Netflix. I got it for Christmas.

Re: Listening to Knuckleheads, Click & Clack,

#8

Lee Gordon

Re: Listening to Knuckleheads, Click & Clack,

Lee Gordon

In the case of this particular puzzler, the wire in question is lamp cord.

Re: Listening to Knuckleheads, Click & Clack,

#9

Uh Oh, Egg on my face,

Keith Newton

I'll admit that I missed the first part of the puzzler, and only caught the last part where they mentioned holding it, using the electromagnet. While I'm sure that would work, I have to wonder if the lamp cord would produce a permanent magnet, without keeping it charged it while fishing for the lost screw.

I just heard enough, that alarm bells went off, when I remembered how i had used this back when I picked up whatever the electricians dropped while trimming up in a breaker box.

Re: Listening to Knuckleheads, Click & Clack,

#10

Actually, I think you are right...

John in NM

But then I never heard the original puzzler, and my electronic theory is kinda sketchy, so this may be worth nothing.

Leaving the wire hooked up would likely melt things and not make an effective magnet. DC must be interrupted to work with a coil. Your technique would produce a single pulse and magnetize the screw driver. Leaving it connected to the battery would turn the wire into a large fuse.

Re: Listening to Knuckleheads, Click & Clack,

#11

Lee Gordon

Re: Actually, I think you are right...

Lee Gordon

There was only one screw for Crusty to retrieve, and when he gave the answer, Click (or was that Clack) made a point to say that it needed to be done quickly and then disconnected from the battery to prevent any damage.