Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

100+ Wood Species + Full-Shop Services: Lumber, Veneer, Tools & CNC. Everything in One Place.

pimpin morticer chisels

Posts

pimpin morticer chisels

#1

pimpin morticer chisels

2B6

On MC (morticer chisels) would there be any advantage to flattening/polishing the outsides like you would the back of a regular chisel. I know this would make the MC slightly smaller, but ya make the tenons to fit.

Has anyone tried something like Topcote on the inside of a MC for chip removal ease?

I used a morticer once & it seemed to me it might benefit from some tweaking. I bought my own now & was wondering if there are some tricks to be shared.

Thanks for letting me on the board. I'm a newbie here. And WOW! Bob Lang is going to be on chat! (be still my beating heart) :{D}

Re: pimpin morticer chisels

#2

Re: pimpin morticer chisels

Tony - Memphis

I polished mine and used a sharpening kit (Rockler?) to sharpen them up a bit too. I think it helped. Haven't tried Topcote, but I did hit the drill bit with wax to try and quiet it a little. Enjoy your new toy!

Tony

Re: pimpin morticer chisels

#3

Several Things

Mark Mandell - Gone Round In New Jersey

If the chisel is properly cone-honed (on the inside) anything more than a 1-time lap on the outside to remove the burr is not needed.

A little PAM on the drill bit will help move chips up and out.

The biggest mistake is setting the auger drill too tight in the chisel. There needs to be a gap between auger and chisel to allow the chips to pass. Easiest way to set the gap is to align and lock the chisel so it's square with the cut-line while leaving the drill just loose in the chuck. Lower everything until all 5 points (chisel-4, auger -1) are just touching a piece of wood. Leaving the drill point touching the wood, raise the chisel just enough to get a penny under the chisel points. With the chisel pint resting on the penny and the drill point resting on the wood, tighten the drill check. You will now have a working gap between the auger head and the chisel interior cone that will (a) allow easy chip movement and (b) keep the bit from screaming as it rubs against the chisel.

Takes longer to write it than do it. ;)

Re: pimpin morticer chisels

#4

Re: Several Things

Alan in Little Washington (NC)

I use a washer to set the bit and chisel, just a tad easier to use than a coin.

I also lightly lap and polish the chisel exterior- especially large chisels whose surfaces can cause a bit of friction/resistance when plunging.

Re: pimpin morticer chisels

#5

Re: Several Things

Robin Corell in Atascadero CA

I use a fine cratex wheel to polish the inside of the chisel and it makes a big difference. Be careful when honeing the outside because it should have a slight amount of relief i.e. it is slightly smaller higher up the shaft than at the very tip. If your chisel lacks any relief then adding a few thousandths will make it cut easier.

Robin

Re: pimpin morticer chisels

#6

Re: Several Things

2B6

I thought about polishing the inside for chip removal ease. I was going to take a bore brush, wrap it w/ 0000 steel wool, & then add JB Bore Paste. I've done this to gun barrels & it makes a difference. (only 12 strokes & not often) So I'm not the only nut that thinks that polishing the inside is a good thing. LOL

I considered instead of tapering the outsides to concave the centers of the side leaving the corners in full contact w/ the wood. Tapering, not being in full contact w/ the wood, may let the bit flex some causing problems possibly. Maybe I'm straining a gnat & swallowing a camel?

Re: pimpin morticer chisels

#7

Not

Mark Mandell - Gone Round In New Jersey

Unless you want a scolloped mortice. The outside of the chisels must be flat and square as that determines how they cut the walls of the mortice. As mentioned, better grade chisels have a very slight taper up their length to reduce friction on the cut surface.

Remember too, polishing a surface pretty much guarantees you'll be spending time repolishing for very little (if any) gain in performance. I've had my bench top unit for neigh on 13 years. I've sharpened the auger with a hand file but have honed the chisels only once in all that time having cut hundreds of holes.

Re: pimpin morticer chisels

#8

Re: pimpin morticer chisels

2B6

Thank you for your replies Tony, Mark, Alan, & Robin. :)

I'm gonna smooth the inside, & concave the sides slightly starting just above the chisel end aprox' 1/2". I"m not going to polish the sides for now, but I will lap once to remove the burr.

Re: pimpin morticer chisels

#9

morticer chisels

AlanWS

I think you should polish the outsides of the chisels, being careful to maintain the flat surface and to not taper them so they jam. There was an article in Fine Woodworking #185 (June 2006) describing this. You hone inside with a cone, repeating as they dull but and don't repeat the outside honing.

Inside the chisel you need chip clearance, and this is smoothed with a chainsaw file. Besides smoothing away any burrs that might impede chip clearance, the author advocated filing near the corners to make the opening oblong rather than round. He also recommended some kind of lubricant spray inside the chisel, but that has seemed to me the least important part of the chisel preparation.

This work is probably not needed with the better chisels, but it dramatically improves performance of mediocre ones. There is a video on the FWW website, but it's in the subscription section.

Re: pimpin morticer chisels

#10

Think about it....

John in NM

Its the drill bit doing most of the work, not the hollow chisel. I sometimes dress up the chisels a bit now and then, but I rarely find they need much at all - only when the mortise is getting visibly ratty on the sides or big chunks get pulled out of the end grain.

The drill bit however, gets frequent sharpening with a triangular file. Most of the resistance you feel in use is due to a dull drill bit in my experience. Actually, a lot can also be due to the return mechanism on the mortising machine, either a big spring or a gas piston.