Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

HD Furniture Grade Ply, Fail...

Posts

HD Furniture Grade Ply, Fail...

#1

HD Furniture Grade Ply, Fail...

Derek Arita

So I saw some "Furniture Grade" pine plywood at $30/sheet at HD and figured it was a good price, So I got some to try out on a shop cabinet project. The sheets I got were nice and straight. A couple of days later, I went out to the garage to start breaking down the sheets and found that the 3/4" sheets had warped, terribly. I figured it would be more trouble than it was worth to return the sheets and try again, so I decided to break these down and hope that the smaller pieces would show less warp.

As I was breaking down the sheets, I saw that the cut edges were not as clean as I'd hoped. When I looked up close, I saw that the top pine layer was flaking off like crazy. That outermost layer is as thin as paper and is brittle. This is the worst plywood I've ever seen and will no longer use it, even for shop cabinets. Beware the HD ply!

Re: HD Furniture Grade Ply, Fail...

#2

Bob

Re: HD Furniture Grade Ply, Fail...

Bob

When I lived in Florida a few years ago they had really good quality lumber. I moved to Virginia and went to HD for lumber Man the stuff they has is CRAP! I thought it was just the location. They must have change the quality they are buying or the supplier Never again even there tool selection has turned to CRAP. just a small step above Harbor Freight.

Re: HD Furniture Grade Ply, Fail...

#3

Re: HD Furniture Grade Ply, Fail...

Ken Krawford

If you really want to see how crappy this stuff is, apply a coat of water based finish. I'll bet the veneer lets loose big time ! Don't ask me how I know this !

Re: HD Furniture Grade Ply, Fail...

#4

Re: HD Furniture Grade Ply, Fail...

Dave Bair

In the past, I've had good luck with their "furniture grade" maple. Been a few years, though.

Re: HD Furniture Grade Ply, Fail...

#5

similar experience reported previously

Bill Tindall, E.Tn.

My stuff was 18% moisture AFTER it had dried some in the shop and become potato chip shaped.

Re: HD Furniture Grade Ply, Fail...

#6

Re: similar experience reported previously

Joe in a Cleveland suburb

Bill posted the reply about 18% a week or so ago when I asked about if I should use 1/2" or 3/4" big box ply for a small project. I've used this stuff in the past (the birch ply they sell). I've only used this stuff in places where I knew quality didn't matter much.

Anyway, went to the blue big box store, bought 5 sheets of 3/4". 3 birch, 2 oak. I wanted all birch, but they only had 3 sheets. It's getting painted, so I didn't really care. These were the 2'x4' sheets - I don't have a truck so I had to get the little sheets.

These 5 sheets sat in my (basement) shop for a week. Each one looks like a potato chip now. Oh, and full of voids too.

Each sheet was around $18. I think $5 each would have been too much.

Re: HD Furniture Grade Ply, Fail...

#7

Re: similar experience reported previously

Larry

I've used it with No problems, I'm in Calif.

Re: HD Furniture Grade Ply, Fail...

#8

Re: similar experience reported previously

Larry in nw ohio

I had the same problem except at Menards ,but I got some of it up before it could all warp. So I wrote them and told them about it and after about 8 weeks and another email the company that sold it to them sent me a check without even wanting to see it. They must know what they sell. I`d write them, politly tell them about it and maybe a picture would help. Larry