Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Compare cordless drills on the numbers that matter

scooping out seats using dado blade

Posts

Re: scooping out seats using dado blade

#26

Re: scooping out seats using dado blade

Barry Irby

My son (about 14 at the time) Said, "WOW Dad, you should hear this guy we found, A black guy, plays the guitar like nobody else....." Jimmie? Jimmie Hendrix? Yeah... If you like him, check out Janis.... and a few others. Neither of them has done anything new lately. Shame. But We grew up with them. Too bad we did not get to grow old together.

Re: scooping out seats using dado blade

#27

Re: back braces

Joseph Mulherin, sr

Rounded over the ends of the braces today. Installed the rear legs on two chairs and allowed a 6 deg slant outward; used 4 1/2" carriage bolts to install and am using some Gorilla Glue. Headrests have been glued up and cut on band saw to 1 1/2" thickness with a 5 deg slant on cuts for the coopering of the blocks; put two of them in place with some clamps to see how things look....OK to my eye. Now shall install the braces and mark the headrest where they are supposed to go and drill the holes tomorrow. Braces are installed using paraffin wax so they move rearward and also sideways. Arms are made and will be installed later next week.

Still have to buy some more Alder to make the rockers for the three chairs, and remake those two front legs I goofed up on. But, things are progressing well and the chairs will be ready for the Xmas presents.

Have taken many pics but do not have the right configuration to send them so you can see my work.

If someone could send me the parameters of doing so I shall use Picase3 to send them.

Re: scooping out seats using dado blade

#28

Re: back braces

Joseph Mulherin, sr

Well, the headrests have been molded, drilled for the upper braces and are ready to be installed tomorrow.

Have to drill the holes for the headrests where they attach to the legs so I have the screws in place when I use tha paraffin wax on the braces and do the final installation on two chairs. Then shall install the front legs on one chair....have to remake the other ones because of a goof I made on the first ones. Everything is being sanded when installed so I am not being overwhelmed with the final sandings. Stopping work for a few days...till about the 12th.

Re: scooping out seats using dado blade

#29

Re: back braces

Joseph Mulherin, sr

Installed the braces on one chair and have the second chair ready to install them too.

Headrests are made for all three...drilled and ready...just have to buy some more wood

to make the third chair braces and 3 sets of rockers all around. Installed the arms on the

first chair and took a couple pics....wish I could show them to you, but alas, no configuration

setup for posting pics.

Re: scooping out seats using dado blade

#30

Re: back braces

Joseph Mulherin, sr

Just have a comment on those damn headrests.....two of them broke when I used a pipe clamp to just snug up the upper legs onto them to hold while drilling the screw holes. Was using Tirebond glue on everything, but I am now going to try the #3 glue.....they say it does not run, gives better holding, and has a longer working time before setting.

Anyway, the chairs are progressing fine....have one chair ready for the rockers; the second chair is on hold till the headrest is suitable again from the additional gluing.... then I can install its braces. The third chair is also on hold because I have to remake those two front legs I goofed up on, and have to make its headrest anew.

Oh, well, still many weeks until Xmas, but they will be ready.

Re: scooping out seats using dado blade

#31

Re: back braces

Joseph Mulherin, sr

Yesterday I went to my wood supplier and bought 20BF of 8x2x8ft of more Alder to do the rockers

and another braces setup for the third chair. So shall be cutting lams all day and maybe some sanding on the installed arms.

Re: scooping out seats using dado blade

#32

Re: back braces

Joseph Mulherin, sr

this morning I setup the Shopsmith to cut the lams...at 3/32" thickness.....BUT the blade kept creeping and would not stay in place no matter how hard I tried to tighten the mechanism. So, I am putting it aside and went and bought a contractor's saw on legs to use as my primary table saw until I can get the head to a repair shop....probably in Whittier, CA. Nuts, I was progressing so fine and then this happens.

Will setup the new saw tomorrow and try to cut the lams for the rockers....48 of them in all, and do some more braces lams. New front legs have been cut....after I lost two band saw blades and had to buy another.

Three blades in less than a week. Expensive hobby....right....LOL

Re: scooping out seats using dado blade

#33

Re: back braces

Joseph Mulherin, sr

Setup the contractors saw on my assembly table, clamped it down, and cut and installed a

straight edge ruler to the table close to the blade so now I have a clear-cut spacing for

cutting the lams without it descending into the blade opening.....works just fine by taping it down.

I have three of those rulers so using one for this setup is not lose.

Re: scooping out seats using dado blade

#34

Re: back braces

Joseph Mulherin, sr

Have decided rather than cut all those lams for the rockers shall make one cut for the upper section and another for the lower section and glue in the Poplar and Oak lams.....less glue and will come out the same in the end.

Re: scooping out seats using dado blade

#35

Re: back braces

Joseph Mulherin, sr

All legs and arms are installed as well as the back braces on two chairs...have to make the other chairs.

Intend to cut the rockers for two chairs next week and install them. Then about two weeks of nothing but grinding and sanding on the arms, and just all around beautifying of the chairs. AQfter that I shall use a clear sealer and a clear poly overall. Must be ready for Xmas for the women.

Then next year I intend on trying to make another 9 chairs for my other relatives.

Re: scooping out seats using dado blade

#36

Re: back braces


Re: scooping out seats using dado blade

#37

chair rockers

Joseph Mulherin, sr

I ordered five new band saw blades which have not arrived as yet, so have setup the new Ryobi contractors saw and shall cut the lams on it for the six chairs and glue them up as needed....more work but i have to do something to get the chairs finished before Xmas.

Have to get out the maintenance manual for the Shopsmith and try to do some work to get the motor wsorking again as it should be. Just poor maintenance on my part over the years.

Re: scooping out seats using dado blade

#38

Re: chair rockers

Joseph Mulherin, sr

Setup the saw and cut all laminations for all three chairs...oak, alder, and poplar.

Am now in the process of gluing everything up....which does take a considerable

amount of time for the glue to setup. Shall install the rockers on the legs using

some epoxy and screws, then use my 3/4" roundover router bit to get the proper

contour I want on them and the legs. Arms have been hollow ground for arms to fit snuggly,

roundovers have been made, headrests installed, back braces installed....just have to do the rockers and then a hell of a lot of sanding before finishing with a honey stain and poly.

Chairs WILL be ready for Xmas presents for the family members....and my doctor gets one too.

Then next year I shall start on the next 9 chairs for next years Xmas.

Re: scooping out seats using dado blade

#39

Re: chair rockers

Joseph Mulherin, sr

Glued up all the rockers for the three chairs; now am gluing the curvatures on them from the legs after cutting them on my band saw...evenly spaced on rockers, then shall sit chair on rockers and install the rear transition pieces for the rear legs. After these are done I shall use my small hand router to go over the rockers and the legs to perfect the curvatures....then a little sanding to smooth out. Will use my grinder and carbide donut to remove much of the rear rockers behind the chairs so the poplar shows thru.

For the finish I have opted to use some honey amber and then some poly over it.

Called the band saw manufacturer and the order hadn't been made up to my specs of 72 1/2" length.

Still the guy said it should arrive by the weekend.... but 2 weeks and the order hadn't been made yet.....

Geez!!!

Re: scooping out seats using dado blade

#40

Re: chair rockers

Joseph Mulherin, sr

Setup the Shopsmith motor and installed the disc sander to run the rockers thru and get smooth sides.

Today I installed the rockers on two chairs and sat in each of them.....feels real good and does rock smooth.

Had to use some wood filler on the joints because they do not meet up as I intended, smoothed them out with

1 1/2"PVC piece of pipe with sandpaper around it to get the curvature I want from legs to seat....sanded real smooth and not noticible...hardly....lol. A little more sanding on each chair and then I shall brush on the Honey Amber color and when acceptable I shall cover with a couple coatings of Shellac.

Re: scooping out seats using dado blade

#41

Re: chair rockers

Joseph Mulherin, sr

After installing the rockers on the two chairs I found out that there was a flat spot close to the front of the rockers....all of them. Debated on cutting them off and shortening the tail rocker by 7", but wife suggested I try to use my portable belt sander and make the curve just under the front legs before cutting them off.

This should work to get the gentle curve needed for the rocker, but I can always remove them and remake.

Problem was originally caused by my not being observant enough when placing them into the forms to bend.

Re: scooping out seats using dado blade

#42

Re: chair rockers

Joseph Mulherin, sr

After finding out that there were some flat spots on the rockers I tried sanding one set on the sander

and reinstalled them on the chair....didn't work....so have decided to remake the rockers entirely

BUT shall cut them out of solid stock...to hell with laminations!!! So, no Xmas presents this year....

but Valentines day is coming.

Re: scooping out seats using dado blade

#43

If it were easy, it wouldn't be fun. 

Merle

Sorry to hear about the set back. I am certain that you will ultimately succeed. Keep at it.

Re: scooping out seats using dado blade

#44

Re: If it were easy, it wouldn't be fun. 

Joseph Mulherin, sr

Thaqnk you, Merle, it was my own mistake in not making sure the lams were in the correct position before applying the pressure to the forms. And, yes, I did learn something....be more slow in your work and make sure things are as they are intended to be before proceeding....measure twice, thrice...before cutting....

Re: scooping out seats using dado blade

#45

Re: If it were easy, it wouldn't be fun. 

Joseph Mulherin, sr

Question to all: would it be possible to use my heat gun and soften the glue on the lams and bend the flat spot until it is curved as it should be?