Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

Blast gates revisited

Posts

Blast gates revisited

#1

Blast gates revisited

larry in nw ohio

Dustmaker Mike Like I said in my post, you should make you own gates and then you could make them in a way that you could modify them to be opened by remote. I put air cylinders on mine and whenever I start any one machine the gate opens and when I turn it off it closes. Quite simple. I bought all my material off Ebay and probably have about $200 in all of it. Good Luck Larry

Re: Blast gates revisited

#2

Thanks

Dustmaker Mike

I have not decided if I am going to build them yet or not. I have limited funds at the moment so to make them Automatic is not in the books. I am saving for my mid life crises (2013 Mustang Shelby GT) so I am trying to do this a cheap and fast as I can.

Re: Blast gates revisited

#3

Bob

Re: Blast gates revisited

Bob

Hey Larry. What did you use to make the gates? How did you power the Cylinder? I assume you have air at each gate.

Re: Blast gates revisited

#4

Re: Blast gates revisited

Alan in Little Washington (NC)

Bob,

I automated my gates several years ago. In order to do it economically you need to do a lot of scrounging. There are many ways to do it, but I found electro-pneumatic to be best.

The main components are a double acting pneumatic cylinder. These can be pricey retail- I got all mine off Ebay. Bimba is a big name to look for. Unless you want to rig a linkage, the cylinder will need a stroke about an inch longer than the size of the gate and you will need to come up with mount for your blast gate.

Prototype autogate:


Next you need a method to control the (15-20 psi shop) air. I used 24VDC, 5 port, 2 way solenoid air valves from SMC. All came from Ebay. There bajillion different configurations and voltages. Some come as a single and some come in manifolds. You may also want a flow restrictor (right angle fitting with orange ring) to prevent the gate from operating too fast and damaging itself.




Next you need a way to control the solenoid- mine are controlled automatically via small current sensor switches (a toroid coil with internal transistor switch) mounted in box adjacent to every outlet that provides power to a machine with a dust collection need. The sensor detects when the machine is drawing power closes the switch. I used CR Magnetics current sensor switches I got on Ebay.


Here is a link to a (rather long) video/slide show of my system.

Re: Blast gates revisited

#5

Thanks for re-posting that, Alan

Henry Higginbotham

I watched this a couple of years ago, and remembered it just last week but had no idea where I'd seen it. I'm working on my first central system right now.

A question: You mentioned that the cyclone cone length should be (at least?) 1.64 times the upper diameter. Where does that number come from, and just how magical is it? I ask because the cylindrical part of mine will be a steel 55-gallon drum, which is about 24" diameter. That yields a conical section 39.4" long, which puts the bottom much nearer the floor than is practical. I'd planned on a cone length of about 15" or so, reducing from 24" diameter to about 12". Am I about to screw things up?

The DC is a Delta 50-182, a 3-hp, 3-phase unit that was made to sit over a 55-gallon drum. A strange unit, to be sure, but an outlet center had it for cheap and that's a major consideration right now.

Re: Blast gates revisited

#6

Re: Thanks for re-posting that, Alan

Alan in Little Washington (NC)

A question: You mentioned that the cyclone cone length should be (at least?) 1.64 times the upper diameter. Where does that number come from, and just how magical is it? I ask because the cylindrical part of mine will be a steel 55-gallon drum, which is about 24" diameter. That yields a conical section 39.4" long, which puts the bottom much nearer the floor than is practical. I'd planned on a cone length of about 15" or so, reducing from 24" diameter to about 12". Am I about to screw things up?

That number is from Bill Pentz's website- I don't remember how he came up with it. ClearVue uses it and Oneida is close on many of their units, while JDS, Laguna and others ignore those dimensions.

Unless you have a monster blower (7-10 hp with 16" + impeller), 24" is too big diameter for the cylinder and cone. The velocity will be insufficient for good centrifugal separation and you will likely get a lot of dust blow-through to the filter. It is not as simple as that however, often a larger diam. cyclone will be spec'd with a lower hp/size blower to avoid too much static pressure resistance- a trade-off of CFM at the source and good separation at the cyclone. Why not just buy some 24 or 26 gauge sheet metal and build a Pentz? I'm not sure what it will cost today, but enough galvanized sheet metal to build my 3D cyclone cost about $50 in 2005. See Bill's website for building info, sizing spreadsheet, templates, etc.

Re: Blast gates revisited

#7

Bob

Re: Blast gates revisited

Bob

Very cool I worked on equipment that had gates controlled by cylinders in the same manor, You have me thinking of a new project.

Re: Blast gates revisited

#8

Re: Blast gates revisited

Larry in nw ohio

Bob My system is very much like Alan. He did a good job of explaining it. The only thing I did a little different was the cyl. hook up. I mounted the cylinder on the top of the gate in the middle so it pushes it slide straight out and not from the side. Also the cyl. are like 1 to 1 1/2" in dia. and 1to 2" longer than the gate opening dia. I`ll look through my photos and try to post some pics. If you have any more questions let me know. Also I do have some parts left if anyone would like to try to rig something like this together. I`m not real sure if I want to let this stuff go, I just have to think about it and see what I want to do. Larry