Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Blast gates

Posts

Blast gates

#1

Blast gates

Dustmaker Mike

Ok maybe not a true blast gate but I do have a question about dust collection blast gates. I am running schedule 40 SD piping in the shop and I was wondering is there a company that makes blast gates to fit the pipe? I really hate using all the adapters and flex hose to connect them but if tat is the only way then so be it.

Thanks

Re: Blast gates

#2

Re: Blast gates

Doug Ridley

Mike, go to your carpet house and ask about the cardboard carpet centers. They will probably give them to you (they did me) and a small section makes a good conection from schedule 40 to a blast gate.

Re: Blast gates

#3

Re: Blast gates 

Doug Ridley


Re: Blast gates

#4

I might just do that

Dustmaker Mike

Thanks

Re: Blast gates

#5

Re: I might just do that

Larry in nw ohio

Mike I made my own, I wouldn`t spend money on any blast gates, when they are so easy to make, also you can pretty much make it out of scrap you may have kying around. Larry

Re: Blast gates

#6

Re: Blast gates

Merle

Mike, I bought these and the flange is slightly tapered so they fit well into the S&D PVC I used (I don't think nit was Schedule 40 however). I also sealed the joint with string caulking to get a good tight fit.

http://www.leevalley.com/US/wood/page.aspx?p=51506&cat=1,42401,62597

Re: Blast gates

#7

Re: Blast gates

Larry Clinton At Frankfort, (Central) Indiana

Mike - can't remember which S&D pipe I used but the gates in the attached link glued right into the coupling and Elbows of the pipe I used. They are shown fitted into the flex pipe but I have one end glued - might want to pick one up or take a coupling of your pipe to Rockler and see if it fits.

Re: Blast gates

#8

The best that I have found

McKay

Clear vu makes a really good gate BUT their sizes do not fit 4 or 6" spiral pipe. I realize that you are using pvc, so it may work. Measure your OD and then call. They are good to work with.

Re: Blast gates

#9

Re: Blast gates

Alan in Little Washington (NC)

Not an answer to your question, but was wondering why you are using Sched 40 instead of the cheaper and lighter weight thin-walled PVC S&D ASTM 2729 pipe? I hope the only reason is because you don't have a nearby source of the lighter weight stuff.

Re: Blast gates

#10

Re: Blast gates

Doug Ridley

My mistake. I said I used schedule 40 . Wrong! I used the thin wall stuff. Sorry.

Re: Blast gates

#11

Re: Blast gates

Alan in Little Washington (NC)

Whew! But Mike said he was using Sched 40???

Now as to the blast gates- I believe ClearVue makes gates that fit ASTM 2729. The size of other gates varies by manufacturer.

There are a number of ways to transition a gate to PVC pipe-

If the gate fitting is the same size or larger than ASTM 2729, you can:

(1) use a section of old inner tube (or a neoprene Fernco fitting) and two band clamps as an inexpensive coupling.

(2) carefully heat the end of the pipe with a torch until it just starts to get rubbery, then slip it over the gate.

If the pipe is bigger than the gate-

(1) use technique (1) above.

(2) if the difference in size is small, add a few tape wraps around the gate fitting.

Or you can take some scrap MDF, laminate, pipe coupling cut in half, and a short section of pipe to make your own inexpensive, easy-sliding, tight sealing male-male, male-female, or female-female blast gates (see my article in the June/July 2010, issue #148 of American Woodworker).

Inner Tube coupling:


Shop-made blast gate:




Re: Blast gates

#12

Hum it was the cheap stuff

Dustmaker Mike

my mistake I was not at home when I posted this and I am not at home now but I will look tonight and see what it is. I am pretty sure it is not the schedule 40 because it was the cheaper of the offerings. I guess I could make the gates easy enough. I want to put a long handle on one of them because it will be under my side table of my table saw and I don't want to bend over to pull it all the time.

Thanks for all the answers

Re: Blast gates

#13

Jesper, Denmark

Re: When you do......

Jesper, Denmark

Remember to leave the gap between the two plates with the holes in them OPEN. You will collect some dust at the end of the gate, and it needs to be able to push it out when you close it, or it will collect and after a little while, it will not close.

Otherwise, you can fabricate from plywood, MDF or acrylic, whatever is around or takes your fancy. The slot does not need to be terribly tight, as the súction from the system will hold the plate sealed when closed.

Re: Blast gates

#14

Re: Hum it was the cheap stuff

Alan in Little Washington (NC)

There are many ways to remotely operate hard to reach blast gates.

One method I evaluated before I automated all my gates was to make my own low friction/easy-to-operate pull cables. I ran stiff but flexible piano wire inside of small nylon tubing, both from McMaster-Carr. I had to make my own end connections and mounts, but my a prototype allowed fairly small radius bends and worked quite well.

It doesn't move as smoothly, but for less DIY effort you can use inexpensive lawnmower throttle/choke cable.

My gates have waxed laminate surfaces riding on laminate surfaces so move effortlessly, but one thing to consider when designing a way to remotely actuate a gate, is how it will operate with the blower on- it can be quite different than when it is off.

Re: Blast gates

#15

Re: Blast gates

Dave Bair, Eaton Rapids, MI

JET makes gates with tapered ends that fit 4" PVC perfectly. Mine are just press-fitted with no glue or chalk, don't leak, and can be reconfigured easily. You do have to support the pipe with strapping, though. I got mine years ago at Menard's.