Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

Tormek planer blade jig question

Posts

Tormek planer blade jig question

#1

Tormek planer blade jig question

David Sparks

I'm considering buying the planer blade sharpening jig for my Tormek. A reviewer on Amazon says that his jig is made improperly so that the blade is not held at a perfect 90 degree angle to the stone. He had to put his planer jig in a vise and beat it with a hammer to try to get it to line up correctly. Has anyone here had this problem? The jig is expensive, and I don't want to buy a defective product. Thank you for your help.

Re: Tormek planer blade jig question

#2

Re: Tormek planer blade jig question

roger lance

I do not have a Tormek or the jig in question.....but before I took to beating it with a hammer to get it corrected, I would return it to get my money back. I do not know of a retailer who sells Tormek at bargain prices; therefore, I'm sure that they would refund your money or replace the jig willingly.

Re: Tormek planer blade jig question

#3

Re: Tormek planer blade jig question

John Lucas

Ditto what Roger says about a return. I have a Sheppac grinder that looks similar and uses the same bar system for mounting the jigs. The jig I have to sharpen plane blades works fine and if it wasn't square could be shimmed to fit. It's the side piece that holds the work square.

I did build a jig for another purpose and getting the 2 holes to light up and fit snug enough to not have slop was challenging. I think beating on one with a hammer would be a little challenging. I bent the two support bearing arms in a vise with some gentle pushing to get them aligned.

So to answer your question, I don't own that jig and don't know the quality. I do know Tormek makes a good tool and apparently has a good repore with the customers so if you bought one and didn't like it I think a return or swap would be likely. I'd call them and simply ask.

Re: Tormek planer blade jig question

#4

Re: Tormek planer blade jig question

Dick Coers

Sorry can't help with the tormek jig, but I can't imagine you can beat the quality of a good sharpener service. Of course I am spoiled with a fantastic service in East Peoria Il. Cobb Industrial Grinding has a 16' long machine that is made for sharpening paper knives. They line all your blades off a straight edge and sharpen all 3 at one time. Then they take off the burr on a power honing machine. You can shave with these knives, and for less than $20 for joiner blades.

Re: Tormek planer blade jig question

#5

Jim DeLaney, Austintown, Ohio

Re: Tormek planer blade jig - No Problem

Jim DeLaney, Austintown, Ohio

I have that jig, and have used it for both jointer and planer blades, with no problems.

Coupla suggestions for better performance:

1. setup is critical. Make sure the blades are properly held in the jig, and

2. Tormek recomments truing your stone with the diamond tool before starting.

Having said that, now that I've converted my jointer and planer to replaceable/disposable blades, I have little or no use for that jig any more. Contact me via email if you're interested in a deal.

Re: Tormek planer blade jig question

#6

(Message Deleted by Poster)


Re: Tormek planer blade jig question

#7

Re: Tormek planer blade jig - No Problem

David Sparks

Isaw your email address and sent you a message, Jim. Thank you!

Re: Tormek planer blade jig question

#8

Word of caution

Pat Evans

I also have that jig. While squaring it to the wheel isn't a problem, using it is tricky. You are moving a long blade back and forth against a much narrower wheel. Just the slightest change in pressure or speed and you can take more off one spot than another. I find that trying to get the edge exactly straight is a problem. Perhaps with 3 blades the unstraight spots won't all line up and the cut will still be fine, but I would prefer a straight edge.

Re: Tormek planer blade jig question

#9

Re: Tormek planer blade jig question

Jim Hoeller

I've been using the planer knife jig for many years and have had no problems with it. A few adjustments allowed me to sharpen 15" knives. Based on the sound of the planer and the surface of a board planed with freshly sharpened knives, I think the Tormek edge is superior to a factory edge. The only down side is the time needed to remove the dings. On the other hand that time can be spent watching the TV.