Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

Vacuum Pump Questions

Posts

Vacuum Pump Questions

#1

Vacuum Pump Questions

Thomas Skaggs, Foothills of Mount Level

A local guy has a used Robinair 4cfm 2 stage Vac-Master vacuum pump and a never used set of vacuum guages for $75. Tempting but don't know much about vacuum pumps.

I have a Vacuum Press pump already that I used for pressing. But another pump might be useful for vacuum clamping or maybe a vacuum chuck for the lathe.

Would this pump do the job?

T.

Re: Vacuum Pump Questions

#2

Yes

Don Orr

That is a good pump and CFM for vac chucking on a lathe. If is an oil bath pump you would be wise to put some kind of filter/collector/condenser on the output side to get rid of the oil vapor/mist which happens when there is any air moving through the pump. Before I knew this I had a cloud of oil in my shop-not good to breathe.

Re: Vacuum Pump Questions

#3

good price...

John in NM

I believe that's a pretty deluxe pump as WW applications go, if the condition is good I'd say pick it up. Might want to see if it works well though, vacuum pumps don't like to be abused, and as I understand it they are a real pain to rebuild (never done it myself though, so that is hearsay).

If you can make a small vac chamber you can pull a vacuum on a half full cup of water - pump ought to boil it at room temp, that will be about 25 mm Hg pressure, which will mean the pump is working properly - just a rule of thumb.

Don't boil it for long though, the water vapor is bad for the oil.

Vacuum gauges are more or less useless IMHO, if you buy the pump go ahead and sell the gauges, you don't need them - there are more accurate ways of figuring out if your pump works or not.

An exhaust filter is a really nice thing to have if its an oil bath pump. Even with the filter you'll get a puff of smoke now and then if you rush a bunch of air through it. They're pretty unpleasant without any filter at all. No idea if the one you're looking at is oil bath or not, but I'd guess it is being 2-stage and all.

Re: Vacuum Pump Questions

#4

Now that I think of it...

John in NM

The gauges are probably accurate enough to tell you if the pump is working well. I couldn't find what the ultimate vacuum is supposed to be, but if the gauge goes down to 25 mm Hg, that is plenty for WW applications. Then you don't have to come up with a chamber (though it's pretty easy to make one) or worry about your oil :D

Re: Vacuum Pump Questions

#5

I'm Guaging Your Response....

Thomas Skaggs, Foothills of Mount Level

....and I find it helpful! Thanks!

Re: Vacuum Pump Questions

#6

As Maxwell Smart Would Say.....

Thomas Skaggs, Foothills of Mount Level

..."missed it by that much". I contacted the seller of the pump and he just sold it. Not meant to be.

Onward!

Thanks for the input anyway!

T.

Re: Vacuum Pump Questions

#7

Re: As Maxwell Smart Would Say.....

Robin Corell in Atascadero CA

If your really interested in picking up a vacume pump look for a local salvage/scrap dealer. The local salvage yard here always has a bunch of them in various pieces of machinery. Some decent units, robinair, kennedy, gast.. and just about any size. I have never gotten down to talking aout how much he would want for one but his prices have always been very reasonable oces I have bought and he always likes to help out someone that is actually going to use the stuff rather than him loading it in different containers and sending it overseas to be melted down.

Robin

Re: Vacuum Pump Questions

#8

Man, too bad...

John in NM

Well, just tell yourself that a $300 pump for $75 was probably rode hard and put away wet :D

I'm always tempted by some huge Welch pumps at our local surplus dealer. He wants $450 though, with no guarantee (rebuild parts would be about that much again). Of course those pumps go for $2k after overhaul, so he's not totally out of line.

I need one for de-gassing casting resin, so lots of cfm is needed - resin sets in 3 minutes, so pulling the vac chamber in about 10 sec is a huge plus. Currently I borrow one when needed, its a bit of a pain but so far not enough to spend the $$$ on my own :D

Re: Vacuum Pump Questions

#9

Re: Man, too bad...

Jason Waters

John,

Have you considered evacuating a cylinder such as a propane cylinder(verify it will stand the vacuum first and not "suck in"), with a smaller vacuum pump, and then using the "vacuum reserve or resevoir" to suck the bubbles from your resin?

Jason

Re: Vacuum Pump Questions

#10

I haven't done the math...

John in NM

But given the low vapor pressure of the resin, it would take a huge vacuum reservoir, at a guess 20,000x the volume of the vacuum vessel. Unfortunately, the process is quite a bit more exacting than vacuum veneering or a vacuum chuck.

Re: Vacuum Pump Questions

#11

Degassing Epoxy

Mark Mandell - Gone Round In New Jersey

I use a shop-vac to pull mix-air out of epoxy; hi volume flow works well. Never used a 3 minute set resin, however. What casting resin are you talking about and why the lightening fast set? Experience tells me "the slower the set, the less reaction heat, resulting in less deformation." I'm interested in new info on materials and specs. Feel free to send it by email.

TIA

Re: Vacuum Pump Questions

#12

Urethane resin *LINK*

John in NM

There are many sources, but I buy it from the guy in the link, mostly because he sells both silicone and resin, and has everything clearly priced - most industrial suppliers require you to write for a quote, and some don't even sell small quantities.

These resins actually cure quite hot, any moisture in the mix will cause foaming as it turns to steam, causing the pour to expand about 5x, ruining the casting and making a huge mess. Most of the gas pulled out in the vacuum is air dissolved in the resin rather than entrained bubbles from mixing, hence the very low pressure needed to degas - something like 27 inches Hg of vacuum, a bit more than required to boil water (I forget what that is in PSI, a fraction of a pound in any case).

Casting urethanes are actually pretty neat stuff, thin enough to pour nicely and tough enough for many applications where injection molding would have been used 30 years ago. It is really hard to design a good mold for a gravity pour though, I've yet to have one work well on the first try, usually it takes me three or four re-designs to get one that really works well :D

I've thought of using them for large scale filler like I used to use West System epoxy in mesquite, but on the whole I think the epoxy really is the idea stuff for that job. I'd bet the epoxy would benefit from a thorough degassing though, I remember many iterations of filling little bubbles :D


Urethane resin

Re: Vacuum Pump Questions

#13

Gotcha

Mark Mandell - Gone Round In New Jersey

BTDT with Polyall 2000. Tried to use it for filling turnings and hardening punky wood. Stuff got so hot it would melt a heavy plastic mixing bowl. Then it would set up with a layer of semi-liquid slime around it. A real mess. The two quarts have been on the shelf ever since. [Anyone want it, send me an email - you pay the postage. ;) ]

Re: Vacuum Pump Questions

#14

Re: I haven't done the math...

Jason Waters

You must be building a boat?

Re: Vacuum Pump Questions

#15

Not a boat

John in NM

Doing urethane casting, and properly degassing the resin requires pulling a vacuum below the vapor pressure of the material (0.06 ATM, 2 inches Hg, 50 torr -- too many units to choose from :D).

The idea is to remove dissolved gasses as well as entrained bubbles (a shop vac will do the latter). Reaching that kind of vacuum would basically require a reservoir significantly larger than what would be needed to equilibrate at 0.06 ATM from ~1 ATM, since there is a very short cure time for the urethane.

For speed, you need a pump that moves a lot of volume and reaches an ultimate vacuum far past your target vacuum, as the pump approaches its ultimate vacuum very slowly. Vacuum is a tricky concept when we get past the rough vacuum of 1/2 atmosphere or so.