Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Gluing up a chest of drawers

Posts

Gluing up a chest of drawers

#1

Gluing up a chest of drawers

Bill Tindall

This case has 26 parts to be assembled without getting one in backwards or out of place. Here is what I do to make it all go smoothly and not make mistakes.

Step 1 was dry fitting every part to see that they would slide together easily and nothing was missing (it was- I forgot a kicker for the top drawer middle). Also make sure the assembly is square by measuring diagonals. If the joinery is right the case will self square. People make the mistake of making joints too tight and then having problems during assembly. If it doesn't slide together with no more than light tapping the joint may be difficult to assemble once the glue swells it.


Step 2 is to lay out everything that is needed and in the order that it goes together. The dividers are all in order with chalk to indicate order and position. Runners are in a stack to the right as they go into the case. Note I have chalk marks all over the place to indicate orientation and position.

I use liquid hide glue as it has the longest working time and it lubricates a joint during assembly where as yellow glue is more apt to grab prematurely.

The back dividers are installed first so that the glue sets a bit and they won't scoot out of position when the front dividers and runners are installed.

Assembled case waiting for the glue to set.


Re: Gluing up a chest of drawers

#2

Re: Gluing up a chest of drawers

Galen Vetterick

If your are trying to say it is as simple as 1,2 and (3?) I know it isn't and you do a great job! ;)

Re: Gluing up a chest of drawers

#3

Bob

Re: Gluing up a chest of drawers

Bob

What no clamps?

Re: Gluing up a chest of drawers

#4

Indeed no clamps

Bill Tindall

There is nothing that needs a clamp. This state of affairs is common with Period furniture design. The dovetailed drawer dividers hold it all together. If the joints are cut right it will wind up square and tight. This case is out of square by only 1/32" across the diagonals.

Re: Gluing up a chest of drawers

#5

Bob

Re: Indeed no clamps

Bob

Very cool I have to try that.

Re: Gluing up a chest of drawers

#6

dovetails lock it together

Bill Tindall


Half dovetails are prepared on each end of the drawer dividers. These dovetails fit in the sockets cut with a chisel into the case side. The guide block is used to chisel the dovetail angle right.

Even dry fit without glue the case assembly is rigid. The glue just keeps the joints from slipping apart.

Re: Gluing up a chest of drawers

#7

Re: dovetails lock it together

Larry in nw ohio

Wow Bill I sure would love to see you work on one of yor project for a few hours. Larry

Re: Gluing up a chest of drawers

#8

Well...stop by any time.

Bill Tindall

E. TN is a wonderful place to visit in fall or spring.

Re: Gluing up a chest of drawers

#9

Bob

Re: dovetails lock it together

Bob

What do you use to make your guide blocks? Do you cut them on a table saw to get the angle right and ho high and long do you mak the blocks 2X4 in.?

Re: Gluing up a chest of drawers

#10

Bob

Re: Gluing up a chest of drawers

Bob

Bill can I ask what size is the case boards and draw rail supports are? They look heaver then 3/4" X 3"

Re: Gluing up a chest of drawers

#11

sizes of stuff

Bill Tindall

The case sides and dividers are 7/8". The dividers are 2 3/8" wide. Why that size....?...I don't know. It looked about right. For a case this size I like to use 7/8". Smaller chest of drawers and it would be 3/4".

Re: Gluing up a chest of drawers

#12

Re: Well...stop by any time.

Larry in nw ohio

Well Bill we are coming that direction in a few weeks to Charleston, SC. . If you don`t mind sending directions, you can send them by email if you wish. Thanks Bill

Re: Gluing up a chest of drawers

#14

link to chest of drawer construction *LINK*

Bill Tindall

http://www.woodcentral.com/woodworking/forum/handtools.pl/page/8/md/read/id/156747/sbj/case-construction-quick-and-reliable/

The guide black is a piece of 8/4 maple cut on table saw to correct angle. The back of the chisel is indexed against it and in a rocking motion the angle for the dovetail socket is carved out.


http://www.woodcentral.com/woodworking/forum/handtools.pl/page/8/md/read/id/156747/sbj/case-construction-quick-and-reliable/

Re: Gluing up a chest of drawers

#15

Looking great-nicely done.


Re: Gluing up a chest of drawers

#16

Bob

Re: sizes of stuff

Bob

Thanks Bill I am thinking of giving it a try I have to build a cabinet to hold patterners and a row of vertical storage for stained glass. Here is what I have design wise so far. I will just be changing the rail size.

Re: Gluing up a chest of drawers

#17

Re: sizes of stuff

Bill Tindall

I would likely do what you originally planned and use ball bearing drawer glides like Accuride.

Re: Gluing up a chest of drawers

#18

Bob

Re: sizes of stuff

Bob

More then likely bottom mount as well because of the size.