Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Price drop on over 1300 Rockler items

Too close this time.

Posts

Too close this time.

#1

Too close this time.

mark Hennebury

A good time for reflection: Finally got caught yesterday.

I have worked most of my life on my own, so I am used to doing things by myself including moving machinery that weighs thousands of pounds around my shop.

Well Saturday i was trying to clear out some space in the shop and decided to move a few machines across to the shed on the back of the house.

I had a machine that weighs about 500lbs 20" x 30" x 48" high on the pallet jack and was trying to wrestle it off the pallet jack onto the concrete and slipped, the machine went over and pinned me by the left leg, a sharp piece of casting was pressing into my shin, my foot was bent in under the machine and the top of the machine was pressing down on my thigh, my right leg was clear but my instep had a big gash and my left forearm was cut up.

I couldn't move the machine, not at all, I thought that my leg was for sure broken. Luckily my wife had just returned home from town, and I screamed out as loud as I could and she heard me and came running out to the shed. I told her to grab a 8' 2x4 and use it as a lever to raise the machine enough for me to slide my leg out, which was the scariest time as I had visions of the machine slipping back down before i got my leg out.

But I was very luck, nothing broken, just bruised, sore and a couple of stitches.

Very grateful that my wife was home to help me.

The thoughts of being stuck there all day will make me be more careful and think of a back up plan in case anything like that were to happen again.

The machine was top heavy with a lot of cast iron up the top and just a sheet metal base, they used to have cast iron bases, which would have been a lot more stable. But with all the weight up high and nothing to balance it out down low, once it started to go there was no stopping it. Anyway I up righted the machine Sunday and moved it into place in the shed and moved another one the same into the shed without incident. Hopefully will use better judgment and a little more respect in the future.

Re: Too close this time.

#2

Bob

Re: Too close this time.

Bob

I'm glad your OK, I guess we all miss judge the laws of nature now and then I know I sure have and it never turns out in my favor ether.

Re: Too close this time.

#3

Re: Too close this time.

Larry in nw ohio

Mark, I do the same thing, most of the time, work alone. But the thing I do is to have my cell phone with me at all times, just in case something happens that I can call someone. In your case, if you had a cell and being caught, you could have called someone. If you have a cell phone, I hope you start to carry it with you. I`m so glad to hear you were only slightly hurt. Be safe. Larry

Re: Too close this time.

#4

Gravity's

Mark Mandell - Gone Round In New Jersey

a b***h, ain't it the truth.

Spent 2 months in PT when I tried to move the 400+lb bandsaw with just one other guy. Foot slipped and the back went south.

Then the cat decided I wanted that carving chisel off the bench with me sitting on the floor. Took 7 stitches to close the 4" incision that just missed the femoral artery.

Glad you're "ok". You might consider one of those "companion" things if you work alone.

Re: Too close this time.

#5

Very lucky...

John in NM

I'm glad you're ok Mark, all too often I hear that kind of story that does not end so well :(

Re: Too close this time.

#7

Oooooo

Mark Mandell - Gone Round In New Jersey

H-E-A-V-Y, Man :D

Re: Too close this time.

#8

Re: Too close this time.

William Duffield

You work with a lot of machinery many hobbyist woodworkers wouldn't be able to identify, but there are machines in most woodshops that can be just as dangerous. In particular, I'm thinking of bandsaws and especially drill presses. A floor standing drill press can squash you even if you're not trying to move it. I used to work for a woodworking tool and equipment retailer. People would come into the store looking for a mobile base to fit their DP. I would always tell them, in no uncertain terms, "No! Bolt it to the floor! Figure out where you want it, and resign yourself to moving anything and everything else around it when you need the room." If you absolutely have to move it, bolt it to a steel plate at least 4' square and move it with your fork lift.

Re: Too close this time.

#9

Ditto

Bill Tindall

Except I tipped the machine over on my wife's leg and broke it. I failed to appreciate how top heavy it was and how easily it would tip over.

Re: Too close this time.

#10

Thanks for the concern.

mark Hennebury

I think that the advice from Larry regarding a cell is good advice.

It is quite unsettling to feel stuck and helpless; I live in an old farm house out in the country , neighbors are not that close, visitors are non existent and had my wife been at work I would have been there the whole day.

I had never really thought about being in this situation before.

I move a lot of machines around the shop, pushing and shoving them, using levers to lift them up onto blocks to get the pallet jack under, and wrestling them on and off lift-gates on the back of trucks, some of the lift-gates are scary, bent down 5-10° and barely able to lift the weight. So I have had many nerve-wracking moments moving machinery.

Hopefully I will be a bit more careful from here on out.

Re: Too close this time.

#11

Re: Ditto

mark Hennebury

Hi Bill,

Sorry to hear about you wife getting injured. I hope that she has fully healed.

Was this a recent event?

Cast iron is deceptively heavy; dismantling machines I am amazed at how heavy all of the parts are, and how easy it is to crush your fingers or pull your back, so when full machines tip there is no chance of stopping them.

Re: Too close this time.

#12

Re: Gravity's

Mark Hennebury

So far i haven't done the back (touch wood) but i know that it is easy to do, and stays around a while. I hope that it healed well.

I also had a run in with a chisel, cant blame it on the cat though:

I like listening to music in the shop and had a habit of throwing tools up in the air and spining and flipping them with the music.Well one particular flip of a nice 1/2" Boxwood handled mortise chisel didn't come down quite as planned and stuck in my knee, just shy of the knee-cap but hit a gusher.

The doctor that sewed it up was quite impressed with how clean the cut was, and asked with what i had cut it.

Its suprising how smug you can feel about doing something so stupid.

Re: Too close this time.

#13

Re: Ditto

TomD

My bandsaw is too big for the mobile base, so I have it centered with some blocks of wood. I have thought of reducing the base, but it would then be less stable. So the other day some of the blocks went missing, and the whole thing fell backwards were I caught it, and didn't know what to do next. Luckily there was a piece of wood on the floor (A clean shop is a safe shop my...) and I got it in there, and was able to lever the saw level, and somehow stabilize it. Then the wife helped me to set it on the base again. I never thought of just dropping it on her, that might of been a step too far, though she is always very supportive. I'd be like "I can set that!"

I hope all worked out well for your wife Bill.

Re: Too close this time.

#14

Re: Thing about this place

TomD

I don't want to make the base smaller because it would be less stable and a fair bit of machining would be required. And obviously the wooden blocks aren't safe. So three seconds after airing it here, I realize I just need to weld some spacers in. Then I realize if I weld them a particular way, they will not only center the bandsaw, but support the brackets that the saw rests on the outer most edges of currently. But for some reason it is a whole lot easier to see the solution when the problem has been aired here first. Amazing!

Re: Too close this time.

#15

That's Funny

Mark Mandell - Gone Round In New Jersey

I got the same comment (about sharp tools) from the ER doc who sewed me up. ;)

Re: Too close this time.

#16

Re: Too close this time.

Stephen Kirk

When I got my table saw, I had 2 friends help me get it off the truck. We knew it was around 300 lbs. But, there is almost nowhere to grab it. Few inches from the floor and it slipped. One scrape on a hand and ding on the base, so we got lucky.

If I ever get to build a new shop, I'm putting in beam and hoist system. We routinely work with such heavy things in our shops that we need such devices available. Too many close calls in my life.

Too bad I can't move all my half ton machinery by smacking it and saying Git!

Re: Too close this time.

#17

Re: Too close this time.

Larry Clinton At Frankfort, (Central) Indiana

I have all my equipment on mobile bases except the drill press and big PM 90 lathe. I also have a hydraulic engine hoist that will pick up a ton or two and if necessary I can use my Ford 9N tractor with loader. Didn't have it when we moved in many of my tools but it sure would have been handy to unload a few of them! I purchased the hoist when I rebuilt the tractor, if I had known how handy it is I would have purchased it much sooner. I lucked out as it was at the local Rural King in a mouse eaten box. They sold it to me for around $120 - it folds up and I have it stored in a little storage shed out of the shop.