Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

duck tape zero clearance insert

Posts

duck tape zero clearance insert

#1

duck tape zero clearance insert

Jerry Gibbs

I just put some duct tape next to the blade of my ts to keep small strips from falling through. Is there anything inherently dangerous about this? I have'nt seen this method used before. The gap was 3/8-1/2". The reason I ask is that I read a review of table top ts that indicates most do not allow for a safe home made zero clearance insert and I might be buying a table top ts for my winter shop.

Re: duck tape zero clearance insert

#2

Dale Lenz

Re: duck tape zero clearance insert

Dale Lenz

Never heard of this method, interesting thought. Think I'd wax the top of the tape so the fiction difference would not interfear(SP) with the stock. I'd watch the leading edge of the tape to make sure it was not coming loose and could stick to the stock and cause problem. Let us know how it works.

Re: duck tape zero clearance insert

#3

Re: duck tape zero clearance insert

TomD

I would not do that since I think that tape is not strong enough, and could fold down into the slot and trap a piece. I would only want really strong, and non-sticky stuff in that area. I would weld, or possible use epoxy (on wood or composite inserts) to make a solid expantion to the slot. They sell junky zinc solder kits for aluminum, but they would be more than strong enough for this.

I don't know what the problem is with table top saws, but I would imagine there is always a solution to what is just mechanics. I don't think zero clearance is a big issue anyway, and often you can do something to solve the problem with either a jig or a process. So for instance you could take two passes so that there isn't a sliver sized piece. Or you can make a pass at a bandsaw so that only the line remains to be taken with the saw. Sleds will be zero tolerance, etc... If the worry is tear-out, a gage mark on the underside will iliminate that.

Re: duck tape zero clearance insert

#4

Re: duck tape zero clearance insert

Robin Corell in Atascadero CA

Another way t achieve a zero clearance insert is to do what we used to do when cutting formica. take a piece of 1/8" masonite and make a cut out that is the exact size or your rip fence, then drop the masonite over the fence and raise the blade up through it. The disadvantage of this method is that for every fence adjustment you end up with a new slot in the masonite and eventually it becomes unusable but it does work for thise times you truely need a zero clearance indert.

The reason we would do this for formia is that the formica is so thin it can slide under the fence and cause a kick back and when that stuff comes back at you it is lke a razor blade, not good. So it is actually a zero clearance insert for the rip fence too.

Robin

Re: duck tape zero clearance insert

#5

Re: duck tape zero clearance insert

Jesse Cloud

I'm curious why the review thought homemade zci's were dangerous on table top saws.

I haven't had a table top saw for a while, but I made them for my old DeWalt and never had a problem.

Re: duck tape zero clearance insert

#6

benchtop inserts

Jerry Gibbs

the depth of the insert was so shallow that only a sheet metal insert would fit.

Re: duck tape zero clearance insert

#7

Re: duck tape zero clearance insert

George Colonel's Workshop-Havertown PA

Hello Jerry,

Its not just the table top saws which employ that lousey design feature of ultra thin ZCI's. My Jet Hybrid shares the problem, as does the Grizzly hybrid. I have made ZCI's (zero clearance inserts) for my Jet by thinning out the ZCI perimeter with a forstner bit in my drill press. One or two for each blade, depending on their kerf thickness. I make the ZCI inserts from hardwoods like oak, and shim where necessary to a table top flatness. It works.

George

Re: duck tape zero clearance insert

#8

Re: duck tape zero clearance insert

Randy Tracy

Hi Jerry , After market inserts for these saws are available at MLCS and are not expensive.

Re: duck tape zero clearance insert

#9

Re: duck tape zero clearance insert

AZ in Colorado Springs

I've done this a few times and not had any problems. I've used this technique only on crosscuts. I use a long piece of duct tape that comes far enough in front of the blade that I can start the cut with the stock and mitre guage on the tape. This avoids the problem of the tape coming up as the stock passes over it. If I was going to use this technique for a rip cut, I'd extend the tape out and fold it down over the front edge of the TS table.

Re: duck tape zero clearance insert

#10

filiment tape

Jerry Gibbs

If I use this technique on a bench top ts where I cannot make a safe zero clearance insert, I might use filiment tape. Jerry