Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Price drop on over 1300 Rockler items

OT water pressure drops

Posts

OT water pressure drops

#1

OT water pressure drops

Dustmaker Mike

Howdy all I have been noticing a drop off of water pressure and it seems to be getting worse as well as a water hammer when sink faucets are turned off to fast. So I figure it is my expansion tank. I notice that ever where I look at the proper instalation of the tank it is after the cold water shutoff before the hot water tank. Mine is located on the main line coming into the house about 40 feet from the hot water heater and before the shutoff so I am thinking that is the cause of the water hammer but would it also cause a drop off of water pressure if it was going bad? I am on city water

Re: OT water pressure drops

#2

Strange

Mark Mandell - Gone Round In New Jersey

My experience is that once you go to city water, you have no use for a bladder tank whose main purpose is to smooth out delivery from a well pump by providing an airmass for the liquid to compress (you can pressurize but not compress water); it's not needed except on a well application. If you're losing flow rate or pressure (they're different) the usual suspect is a filter of some sort in the lines. Do you have a softener and/or neutralizer or other treatment fixture in the line?

The other possibility is that your water company is cutting back on usage because of the wide-spread drought. If your area is effected that way, call the water co. and inquire.

Re: OT water pressure drops

#3

Re: OT water pressure drops

Larry in nw ohio

Michael From your post it sounds as if you use to be on well water awhile back. It maybe that your line is pluging up somewhere, and the first place I would look is something like a filter. If you have one, take the filter canister out of the container and look inside to see how clean or dirty it may be. If it`s dirty, that may be the place. Leave the canister out and try the water for awhile and see how it works. Good Luck. Larry

Re: OT water pressure drops

#4

Re: OT water pressure drops

Al Stokka - Cambridge, Iowa

Mike,

Does your expansion tank contain a elastomer bladder? If not, the air cushion will gradually be dissolved into the water flowing through the tank and the cushion no longer functions.

Al

Re: OT water pressure drops

#5

Re: OT water pressure drops

Barry Irby

Some areas are requiring a small (Gallon or two) expansion tank in the system to allow for the expansion of the hot water and not cause back flow into the municipal system. apparently some water meters will not permit any back flow and thus the system might super pressurize when the water heater comes on and no faucets are open.

These tanks could also act as anti hammer chambers. If you have one of these and it has become water logged (lost its charge of air) it would not longer function in either capacity.

If you have a pressure reducing valve it could fail or clog and reduce the flow rate through out the house. It would be immediately after your main water shut off if you are on a city system. You would not have one on a well.

If you lose pressure/flow every where You probably have a restriction early in the system.

Re: OT water pressure drops

#6

Re: OT water pressure drops

Dave Paine

If you are on city water, I think the expansion tank was preventing water hammer.

If this has lost its seal, then you will get water hammer, since there is nothing to absorb the shock wave from any device turning off.

Feels like the unit more than its placement.

Re: OT water pressure drops

#7

Re: OT water pressure drops

Lee Schierer McKean, PA

Loss of pressure and water hammer are not caused by the same things. Water hammer is caused by the momentum of fast flowing water suddenly being stopped by a valve closing. Water hammer is usually one loud bang when a valve is shut. Air chambers should be located as close to the offending valve as possible and generally an entrance expansion tank does not serve that purpose. Improperly secured pipes can contribute to the problem. It usually occurs in higher pressure systems, particularly with solenoid valves.

However, water hammer can be caused by loose faucet washers or worn faucet stems which "rattle" in their housings when the valves are just cracked open.

If there is a pressure regulator in your system, which is likely if you are on city water, then it could have failed, which would explain your pressure loss.

Lee

Re: OT water pressure drops

#8

Thanks All

Dustmaker Mike

I don't have a filter in the line nor do I have water softener. I will pull the expansion tank and place a new one near the water heater to see what happens. The water hammering has gotten worse since I moved into the house in 2007. So I am thinking it is the tank. We shall see.

Thanks

Re: OT water pressure drops

#9

Jim DeLaney, Austintown, Ohio

Re: Thanks All

Jim DeLaney, Austintown, Ohio

Mike,

The expansion tank might be the cause of the hammer, but the pressure drop is a separate problem. If you have a whole house pressure regulator, then it's the likely culprit. I had to replace mine to solve a problem similar to yours. BTW, in my area, the unregulated pressure exceeds 135psi. I have the regulator set for about 60psi.

Also, if you have a regulator, you definitely need an expansion tank, because the regulator acts as a backflow valve, preventing expansion (from the water heater) from buffering back into the system. Without the expansion tank, the pressure rise can/will pop the pressure/temp valve on the water heater.

Re: OT water pressure drops

#10

Re: OT water pressure drops

Tony - Memphis

I recently started hearing some hammering in our system. After some research, I suspected it was a shower cartridge. I replaced it and the hammering stopped. I hope that fixed it.

Tony