Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

epoxy and sawdust mixing

Posts

Re: epoxy and sawdust mixing

#26

Alternatives to epoxy

Bob Lang

I agree with the comments that the 5 minute epoxy isn't worth much, unless you want something to only stay together for 5 minutes. For the purposes of making a filler, there are several alternatives that are easier to use and cheaper. Basically, any clear sticky stuff that dries reasonably hard can be used. Duco Cement (not sure if it's still on the market) or model airplane glue come in a handy tube so you can squeeze out a little blob and mix in fine dust. Dries a shade or two darker than the wood, but takes stain okay, and is hard to see after a finish goes on. Either of these are dry enough to sand in half and hour or 45 minutes. Blond shellac or lacquer also work pretty well, but take longer to dry.

Bob Lang

Re: epoxy and sawdust mixing

#27

David Barnett

(Message Deleted by Poster)


Re: epoxy and sawdust mixing

#28

Re: Cups

Joseph Mulherin, sr

Thank you, Mark, that answered the question I was going to post later. So, I shall use the 30 minute epoxy, mix up the hardener and resin first and then add the wood filler. Don't really need too much at one time, but since this is my first attempt at epoxying I had to ask these questions.... and the information was helpful to others too I see. This WC IS the BEST.

Re: epoxy and sawdust mixing

#29

Re: Cups

Joseph Mulherin, sr

Today I went to the shop intending on doing the dust control...clean up all the saw dust that has accumulated over the past six weeks, but this leg has miniscus( I liken it to the cover on a baseball...and it has a tear which radiates out to the ligaments and muscles) problems and is soooo sore at times I have to cover the knee with an ice bag just to get relief. Don't see the Orthopedist for another 2 weeks....and then no telling when the surgery will be scheduled.. Hard to even stand on the leg for any length of time.

So, with the chair assembled pretty much, and have to do the routing of the edges and much sanding...I am going to stop for awhile till this leg situation is cleared up

Re: epoxy and sawdust mixing

#30

Ambroid too... *LINK*

John in NM

Even found a kinda neat little history of how it came to be... never knew all that when I was sticking balsa airplane kits together.... just down river from Old Town too :D

Balsa airplane kits were tons of fun, once the novelty of the finished plane wore off, one could wind it up, spray with WD-40, light it, and launch it from the upper floor of the barn (on a snowy day of course :D ). Mom was horrified, but of course Dad said "Why didn't I think of trying that?" :D


Ambroid glue history

Re: epoxy and sawdust mixing

#31

Re: The real story, and o-rings

TomD

Nobody could be a more fervent WEST supporter than I am, but these days there are a lot of products to choose from. Actually, my 5 minute is also made by them. On YOUTUBE, you can see a video where they repair a carbon spar using West 105 and 5 minute to speed up the cure. Their 5 is pretty good, as is Devcon. The main reason to use WEST it it's superior structural properties.

If you want to colour the 5 use something that isn't a thixotropic agent also. Sawdust is also a little too large, and does not compact well, so in small repairs it often lacks correct granularity. For repair I normally mix in whatever will blend best. So I might use carbon powder if I was trying to ape the black pigments in cherry.

For outright hiding, super glue is usually the best approach, but you can't be filling too much. With super glue and sawdust one can make invisible repairs, with epoxy even if the dust starts out the same colour it normally ends up a lot darker.

For dispensing small amounts of epoxy, I use o ring syringes. I haven't used this place, but it looks good:

http://www.squirrelsandmore.com/rehab-supplies/oring-syringes.html

These will hang in there indefinetly, and they do not pop off like some of the rubber plungers. For really long term use one could substitute epoxy compatible O-rings.

With the 5cc syringes I use, the trick is to drill a 3mm hole in whatever cap comes with whatever you want to dispense, and then mount the syringe in that hole, it will be a an air tight seal. Once, before we could buy all this stuff online, I scored 25 of these syringes at a very cheap price. Up till then they were 3 dollars each in drug stores. Anyway, with the windfall of syringes, I mounted these babies in virtually every bottle in the house, from detergent, to epoxy.

For larger projects I am supposed to be making a machined aluminum pump, but my laziness knows no bounds.

Re: epoxy and sawdust mixing

#32

Sorry to hear of the knee troubles.

Don Orr

Best wishes for a successful surgery and speedy and complete recovery. Hope you'll be back on your feet soon.

Re: epoxy and sawdust mixing

#33

Re: Sorry to hear of the knee troubles.

Joseph Mulherin, sr

Thank you, Don, and thankGod for the ice bags I use almost all day

Re: epoxy and sawdust mixing

#34

Re: Cups

Joseph Mulherin, sr

Bit the bullet this morning and went out and moved some machinery around and cleaned up the saw dust and scraps accumulating all around. Came out satisfactory for now. Moved my Jack-Bench to the center of the room and lifted my chair up on it so I can run the router on all edges and do some grinder sanding on the seat front edge contour, and route the headrest edges too. After that I shall lay the chair on its back and install the rockers to the legs with epoxy and bolts. More routing to be done on them to finish up the contours on the rockers. And arm boards have to be grinder sanded for contour in center of board where arm rests, then glue them to the chair posts and upper front legs.

I have found out things I shall do differently on next chairs as far as preforming the pieces before assembly, but that is the joy in woodworking for me.

Re: epoxy and sawdust mixing

#35

Re: Cups

Joseph Mulherin, sr

Hey, Mark, I did as you said about mixing the two together and then added the saw dust.

Used some of the 5 minute epoxy just because I had it and thought O would give it a try....it cam pout fine on two cuts. Stuffed it in the joints and covered them with tape to keep it in place and not run out..Took off tape and the joints are satisfactory ready for finish sanding. The color was a little dark, but in finishing it should not be noticable. I used one of my medicine bottles cut down to cup size , and I nave many of them for future use.

Re: epoxy and sawdust mixing

#36

Re: Tape

William Duffield

The best tape I've found for keeping epoxy from running out of joints, knots and borer holes is clear plastic strapping tape. It releases from the epoxy effortlessly (either glued or unglued side) and leaves a smooth surface that usually doesn't need sanding, except to match the finish of the surrounding wood.

Re: epoxy and sawdust mixing

#37

Re: Cups

Joseph Mulherin, sr

Been working on the chair doing the routing and sanding on edges this morning. Everything is coming along just fine. I have been using the 5 minute epoxy to fill in some marks , mixed in very small quantities, fill in and let sit until dry, then sand over the epoxy to smooth out....and it does blend in with the wood seat nicely. Stain should cover any differences in colors, and they are in unnoticible places anyway.

Sanded the arms groove and am ready to install them on chair. Headrest is finished and am ready also to install the back braces and headrest. Then concentrate on the rockers.... entire assembly should be finished this weekend. Then plan on covering the entire chair in three coats of Deft, the maybe a couple coats of poly

Re: epoxy and sawdust mixing

#38

New Plan

Mark Mandell - Gone Round In New Jersey

Putting poly over Deft is a waste of both. If you want a lacquer finish, stay with it. Minwax's rattlecan lacquer does better (I think) than Deft. If you want a poly coating go with that. It also comes in rattlecan spray if you don't have the equipment.

Don't mix the two.

Re: epoxy and sawdust mixing

#39

Re: New Plan

Joseph Mulherin, sr

Yes, Mark, I have changed my mind on this poly. I went to the Search engine and found the Deft retailer and I am going to purchase some colored stain for the chair. They have many colors to choose from...just have to decide which one will match into the individual families decors It does not need any poly because it already has the needed finish I want. I really do appreciate you guidance.

This afternoon I sanded some more and the epoxy joints came out very nice. Sanded off the over coverage and the wood came thru just as it it did not have anything ever put on it. I also installed the headrest and the back braces...just have the rockers to do later over the weekend. I looking at the chair right now...I think I shall keep this one for myself and make some changes for the ones I make later. But, all-in-all the chair came out as designed by Hal Taylor....with some modifications of my own construction-wise.

Took many pictures during the construction, but I really do not understand how to post them here on WC with its 100kb limitation on size.