Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Fast and affordable laser cutting – so you can make the parts you can’t find anywhere else

Progress on Chest of Drawers

Posts

Progress on Chest of Drawers

#1

Progress on Chest of Drawers

Bill Tindall

The sides of this chest of drawers will be a Period correct frame and panel. The attractiveness of frame and panel depends on the frame. It should complement and not detract from the more showy panel. Here I am arranging rails and stiles for best effect.




Next mortises are prepared. I chose to chop them with a chisel made from a piece of tool steel bar stock. I find a hand chopped mortise to be more precise and have smoother sides than a hollow chisel made mortise.

I make tenons in a way that results in reliably crisp joints.


First I scribe the depth of the mortise on all four sides of the rail. Then I saw the thickness of the tenon on the table saw. Note the white poplar spacer piece. It is precisely sized so that when I make the first cut with it in position and the second cut with it removed the result is a tenon of precise thickness to match the mortise.



Next the waste of the tenon is cut away and the tenon depth is precisely chiseled to the base line previously scribed. This approach results in tight fitting joints.


The tenon lengths are marked and waste removed.


Finally, the fitted joint.

Re: Progress on Chest of Drawers

#2

Further notes

Bill Tindall

1. It is easy to get things mixed up. Note chalk circle to indicate face side of rail. If all measurements an operations indexed from the face side minor variations in thickness are pushed to the back of the frame where they don't show.

2. Moldings top and bottom hide some of the rail, so don't get excited that there is crummy wood on the edges of the rails.

Re: Progress on Chest of Drawers

#3

David Barnett

(Message Deleted by Poster)


Re: Progress on Chest of Drawers

#4

Walnut came from a unique log

Bill Tindall

The log had some huge nails about 3' up from the base of the tree. Hence, it was rejected as a veneer log in spite of the fact it was big. The mill waited until the replacement bits on their saw were shot and then rift and quarter cut the log for me. It turned out we were able to avoid all but one nail. The wood from this tree is unlike any I have ever seen in walnut. It has the texture of mahogany and it is as light as poplar. Growth rings are indistinct as though it laid down no summer wood. It is a dream to carve as May May reported when she carved a piece for me.

It is a bit dead looking till the finish hits it but it finishes fine.

Re: Progress on Chest of Drawers

#5

Bob

Re: Progress on Chest of Drawers

Bob

Very nicely done. I like your panel sled what size is it?

Re: Progress on Chest of Drawers

#6

saw sled details- sawing stiles

Bill Tindall



I didn't discover this valuable table saw addition till most recently. What I was missing!! I didn't know how big to make it. I had part of a sheet of 1/2" birch ply that was just a bit bigger than table saw top. So I arbitrarily made it that big and I find the large size most useful. The runners are white oak and work fine.

Re: Progress on Chest of Drawers

#7

Re: Progress on Chest of Drawers

William Duffield

If you are considering using it to cut out kitchen cabinet components, make it 26" deep, to accommodate both cabinet sides and countertops. Once you have made one that big, you will find that moving it on and off the table saw and hanging it on the wall or ceiling is inconvenient, to say the least, especially if you make it from 3/4" plywood, so you will probably want to make a second, (and maybe even a third) narrower one, for squaring up cabinet doors, drawer components, etc. I find 3/8" plywood is sufficient, because the fences, and the saw table keep it flat in use.

Re: Progress on Chest of Drawers

#8

Re: saw sled details- sawing stiles

larry in nw ohio

Bill I can`t see from the picture if you have a cover on the sled where the saw blade comes thru on the back or not. I call the back the where the blade comes thru and just looking for a hand to cut off. If you don`t please screw a piece of soild oak or something of the sort to cover the saw blade when it comes thru. I have something like a 2 1/2X 2 1/2X 4" long piece. Be careful. Larry

Re: Progress on Chest of Drawers

#9

sled safety

Bill Tindall

A thick backing piece, followed by a piece of aluminum plate followed by another piece of wood provides an audible indication of imminent danger. Aluminum won't damage a blade but it makes a distinctive noise as a warning the blade is about to emerge from the back of the slid.

Of course one could use the saw stop approach and put a blade-destroying piece of hardened steel plate behind the slid.

Re: Progress on Chest of Drawers

#10

Bob

Re: Progress on Chest of Drawers

Bob

So far I have two, one is 34X28 but I need a bigger one for squaring cabinet sides. I want to make a small rolling table to but at the in-feed to get the sled started level, just 3/16" to 1/4" lower that my saw. I use 1/2" Baltic birch and employ the "5 cut method". I worked hard to get the one I have to be under half of one one thousandth but it was well worth the time spent..

Re: Progress on Chest of Drawers

#11

Re: Progress on Chest of Drawers

William Duffield

The 26" dimension I provided is NET, in other words, inside dimension between fences, not outside dimensions. Sorry for any misunderstanding. The outside dimension would be at least 29" if you use 2x material for the fences.

Re: Progress on Chest of Drawers

#12

Ellis Walentine

Strong beginning

Ellis Walentine

for a shop shot. By the time you finish this piece, it will be quite a nice article.

Thanks for the update.

Ellis