Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

NiCad batteries

Posts

NiCad batteries

#1

NiCad batteries

Doug Ridley

I have two Hitachi 14.4 Drills about 4 yrs old that I use a lot. The batteries have gotten to where they don't last long between charges. Lowes wants $60.00 each for new ones and that translates to $160.00. for the four of them. I find a place on Amazon that has what it says are new ones for $40.00. Does anyone have any experience with batteries off the internet? I am leery of buying things I can't see in advance. Any other suggestions welcome.

Doug

Re: NiCad batteries

#2

Call Hitachi

Mark Mandell - Gone Round In New Jersey

I did that with Rigid NiCads for my old 12v and they gave me a source selling them for $25 each. The other remedy is to pitch the whole thing and just buy a new drill for about the same price.

Re: NiCad batteries

#3

JL

Re: NiCad batteries

JL

I have used a battery rebuilder (MTO) for my Dewalt batteries. I then bought some from Amazon as they were less expensive. I have since used Amazon (or Acme Tools which sells through Amazon).

Why so many batteries? I picked up three 14.4 V Dewalts for ~$30. The batteries were close to useless. Now they all have newer batteries and work quite well.

Re: NiCad batteries

#4

Re: NiCad batteries

Gary Smyth

I've never been burned by Amazon. Even if buying used/rebuilt items never a problem. That's not to say others haven't had a bad experience, but not me. In one instance Amazon even stopped an order once when I mistakenly bought the wrong model. My refund was almost immediate and I didn't have to buy the correct model as a requirement from them either. As far as I'm concerned they are a stand up organization.

Re: NiCad batteries

#5

Bought Milwaukee Battery last week from Amazon

George Colonel's Workshop-Havertown PA

Good Afternon Doug,

Both batteries in my Milwaukee 12 vt drill/driver went south. I took them to Milwaukee Repair Station and learned that even after 4 years, they were covered by warranty. Whle Milwaukee had the defectifve batteries, I ordered one replacement from Amazon. Its fine. I would not hestitate to recommend them. Actually, all three batteries were the up-graded version of the original.

I would approach Hitachi for warranty action. Failing that, get them rebuilt by Primecell or other similar outfit.

George

Re: NiCad batteries

#6

Re: NiCad batteries

Russ

I hope I can break in here and ask about a related situation. I have an old, beatup but still running well Porter Cable nicad powered drill, model 862. This is the classic dating way back. I have two new, rebuilt nicad batteries. What doesn't work is the charger. I can't seem to replace it, rebuild it, or buy new. Am I just going to throw this perfectly running drill into the trash?? Seems like a true waste!!! Any suggestions???Thanks!!! Russ

Re: NiCad batteries

#7

Re: NiCad batteries

John McGaw

When you have tried to get the charger repaired, where did you go and what were you told? These chargers aren't terribly sophisticated as such things go and it is hard to imagine that they use any proprietary parts that a good technician couldn't work around. Worse come to worst, if you could do without the super-duper-quick-charge ability, there are other chargers that could be kludged to do a slow charge on your battery packs using the old shell for nothing but its contacts.

Are the batteries in question the old standard PC slide-in type? There are still chargers around that work with 12/14.4V batteries and if yours are physically identical then you could probably buy something like an 8604 (I have one of these myself) although the price is pretty painful -- $50 bucks at Amazon Marketplace.

Re: NiCad batteries

#8

Re: NiCad batteries *LINK*

John McGaw

You might want to contact these folks to see what they say about charger parts/replacements. They claim that they can handle virtually anything in the way of replacements. I didn't dig too deeply into their site since it is pretty large and scattered.


Tool Parts Direct

Re: NiCad batteries

#9

blown charger

Gary Camp, Bend Oregon

I had a poor neuetral / ground to my shop. voltage varied from 70 to 180 plus and switched legs. My 18v Li charger failed. One of the ElectroMagicians at work took it apart for "training" replaced a failed part similar to an MOV works again, 5 bucks in parts

glc

Re: NiCad batteries

#10

Re: blown charger

Doug Ridley

Thanks for all thr info. They still work, just don't hold a charge very long. I will delay the inevitable for a while and then probably go to Amazon for four new ones.

Doug

Re: NiCad batteries

#11

Re: NiCad batteries

larry in nw ohio

Doug I have had my DeWalt batteries of verious voltages rebuilt at www.voltmanbatteries.com and they did a good job and a little cheaper. Of course they were a little more expensive than the stores because I had them put in 3.3 amp. cells, almost half as much bigger than the old cells that are something like 2.2 amps. When I first used it, it really surprized me and almost jumped out of my hand. :) I am pleased in doing it and I would suggest at least looking at their site and see what they got. Good luck however you go. Larry

Re: NiCad batteries

#12

Re: NiCad batteries

Russ

John, thanks for the info on possibly getting the charger repaired. I went to the two "authorized" repair places for PC products in Boise and was told the same thing, that the parts to repair the charger are unobtanium!! I will give your suggestions a go. I think your are right about the proper tech being able to repair it. I just haven't found one yet!

Re: NiCad batteries

#13

Chargers

Bill Tindall

Any NiCd charger will charge if you can rig a connection. In fact, a high quality charger which may take a day to charge this large batter will promote longer battery life.

Re: NiCad batteries

#14

Re: NiCad batteries

Ron in Eugene

I had two Porter Cable batteries that went bad, but I didn't want to toss the drill and buy a new one. They, Amazon, wanted about $80 for one replacement battery. So I went to eBay and bought some individual NiCads of appropriate amps and volts and rebuild BOTH batteries for less than the cost of one new one.

Take the one you have now apart to see what batts you need.

You can easily find videos on YouTube that show hoe to do it. If you have or can borrow a solder iron/gun it is really easy to do. Of course this assumes that you can easily take apart the batts you have now - mine had a few screws. Hope this helps you.

All the best -

Ron

Re: NiCad batteries

#15

Re: NiCad batteries

Ron in Eugene

Larry, thanks for jogging my memory - Voltman is where I bought my batteries on eBay. Was quite pleased with the service and the product. HTH