Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Price drop on over 1300 Rockler items

Speaking of Abrasives......Torn belt?

Posts

Speaking of Abrasives......Torn belt?

#1

Speaking of Abrasives......Torn belt?

Barry Irby

I used my 4x24 PC belt sander to level the edge of a piece of subfloor I installed. The adjacent floor still had hundreds of 1/4" crown staples left from the underlayment we removed. I snagged a staple and tore a belt. Put on a new belt and went at it straight on without swinging the sander. Tore another in about ten seconds. Pounded down the staples and tried another and it too only lasted a few seconds. The last two belts tore at the joint. These are bi-directional belts without the old fashion overlap. Can you not sand sharp metal staple shards with theses belts joined with tape?

Re: Speaking of Abrasives......Torn belt?

#2

David Barnett

(Message Deleted by Poster)


Re: Speaking of Abrasives......Torn belt?

#3

Re: You didn't say...

Barry Irby

I left the broken belts in the house I am working on so I can't see them to check the brand. One of them was rusty red so I think that might be Lowe's Gator Brand. It shredded badly, so I think I snagged a staple with the edge of the belt. the other two may have been locally made by Virginia Abrasives down in Petersburg, VA. I buy boxes of ten from them. they have a wavy sort of serpentine joints dark brown/black abrasive.

IIRC I used to sand sharp stuff with the old style belts. I was hoping it would be effective to sand off the staples rather than pounding them down.

Re: Speaking of Abrasives......Torn belt?

#4

Re: How Old were they??.....Torn belt?

Larry Clinton At Frankfort, (Central) Indiana

Barry, I remember a few years ago, when I was still using some Crapsman products, there was a clearance sale at Sears on belt sander belts. I purchased several belts of various grits. Four or five years later I still had some in stock. I had a job where I really thought I was going to save money as I had these - started sanding - no nails or other issues. Belts ran a few seconds and separated at the glue line. ALL the belts failed in the same manner in no time. This was before I had an air conditioned / heated shop which may have something to do with this. I don't know what the bonding process/material is, but I have even seen premature failure of belts I have stored in my new shop for less than 3 years (on other brands of belts).

Re: Speaking of Abrasives......Torn belt?

#5

David Barnett

(Message Deleted by Poster)


Re: Speaking of Abrasives......Torn belt?

#6

Evidently not.....

roger lance

but you could keep on trying the same thing and maybe get a different result.

Re: Speaking of Abrasives......Torn belt?

#7

Leo Cuellar

Re: Great! Now I have to worry...

Leo Cuellar

It might have been in a Klingspor catalog that recommended not buying more belts than you could use in a one year period, just for that reason. That said, I have a stockpile of Grizzly belts, stored for several years, in the worst conditions that I've not had any issues with yet.

Re: Speaking of Abrasives......Torn belt?

#8

No

Mark Mandell - Gone Round In New Jersey

Belts are for wood not nails.

1. Pound them flat or even better, slightly dimpled, and mark each one woth a magic marker as you go.

2. Put a 36 grit hard disc on a 4" angle grinder/sander and hit'em each a lick or two. Then use the belter if you need it. Small belt sanders need belts that are relatively thin to make the small radius curves on the platens. They won't handle nails (or staples).

Re: Speaking of Abrasives......Torn belt?

#9

Aside : bi-directional

Yonak

I was speaking with a technical consultant at Klingspor last week and was told most people don't know that belts joined with tape are all bi-directional, despite that they may have an arrow.

Re: Speaking of Abrasives......Torn belt?

#10

David Barnett

(Message Deleted by Poster)


Re: Speaking of Abrasives......Torn belt?

#11

Belt & Nails

Mark Mandell - Gone Round In New Jersey

Barry's staples are surrounded by soft wood so the belt will dig in on either side, but the nail will protrude and put extra point pressure on his belts. His sanding belts aren't structured for that. I've used a belt sander to shape/sharpen a chisel in the field, but the load is light and even across the whole blade rather than asking the abrasive coating and fabric backer to deal with a sharp point load.

Re: Speaking of Abrasives......Torn belt?

#12

I'm thinking....

Barry Irby

That the belts may be five years old. I talked to the technical guy at the local factory and we discussed the aging thing. He told me they found some that had gotten lost in a off site warehouse and were about 8 to 10 years old, IIRC. They tested them and found little or no degrade.

I think the first belt failed because I slewed it into the staple and ripped the edge. My mistake.

The second two both failed at the join, I think the staple caught an edge in the join and pulled it loose. May have grabbed it at the front roller while it was curling around the drum.

And I don't think I am guilty of trying it over ad over expecting a different result, (that only works with DOS based computers.) The belts were different brands and I felt like I ruined the first one. The second one failed and I was suspicious it may have been age related, so I tried again. When the identical one failed, I quit. For what these things cost, I need more than a few seconds of performance.

Re: Speaking of Abrasives......Torn belt?

#13

Re: Belt & Nails

Bruce, a MN Galoot

I've sanded off the tips of drywall screws that protruded through pine boards without ever a problem. That works much better than trying to cut them with your only good resaw bandsaw blade that cost a lot of money. BTDT :D

Re: Speaking of Abrasives......Torn belt?

#14

Re: Belts

Mark Mandell - Gone Round In New Jersey

Maybe there's a difference between getting nailed and screwed. :D :D

My experience, however, has been the same as Barry's and my info was what I got from a floor sander guy. :\

m

Re: Speaking of Abrasives......Torn belt?

#15

Re: I'm thinking....

Ken Oakley-Sunny St. Cloud Fla

That is amazing