Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

Multi tool/oscillating tool Questions.

Posts

Multi tool/oscillating tool Questions.

#1

Multi tool/oscillating tool Questions.

Barry Irby

I have a Bosch MultiX tool. Like the Fien and many other brands on the market. Mine is battery powered and I have liked and enjoyed it, but it has gotten to be touchy. If you over load it in the least it just stops and you have to turn it off and back on.

I was thinking it might be time for a corded one. I was in Lowe's and they have several brands starting at

$99 with a number of them at $119 up to $149. They also have a Bosch Corded one one "special" for $199 and they throw in a bunch of blades. Now I am wondering if the Bosch version or any of the others will accept various brands of cutters. The Cordless Bosch I have now will accept any brand.

(My biggest complaint about this tool is the blades are ridiculously expensive.)

Anybody got any advice? Which one do you have? Which would you buy? Know of any reviews?

Re: Multi tool/oscillating tool Questions.

#2

Re: Multi tool/oscillating tool Questions.

Larry in nw ohio

Barry I believe that most cutters are interchangeable, sometimes you need an adapter, you`ll need to look at the cutter display, that`ll tell you. I have the Rockwell and like it but of course it`s all that I had. As long as you get a pretty much name brand you shouldn`t go wrong. Good Luck with whatever you get. Larry

Re: Multi tool/oscillating tool Questions.

#3

Re: Multi tool/oscillating tool Questions.

Joseph Mulherin, sr

Barry, I bought the one they have on Harbor Freight along with some extra blades for wood, and I am very well pleased with it...corded too. Cost only $29 at the time, and it does all the work I need to do with it.

Re: Multi tool/oscillating tool Questions.

#4

I have the Bosch

Lee Schierer McKean, PA

After using a Dremel Multitool, I liked what it could do, but not the fact that the Dremel got very hot, almost too hot to hold. I put the Bosch Multitool on my wish list and it showed up on Father's day. As I recall, it will use almost any brand of cutter, but as others have indicated you may need an adapter. I've only used mine once so far in the sanding mode and it worked great, I just wish they offered finer grit sandpaper than 120.

Lee

Re: Multi tool/oscillating tool Questions.

#5

Re: I have the Bosch

Keith Newton

Lee, have you looked into the possibility of cutting a 6" finer disk?

And Barry, I find it easy to re-sharpen the standard blade. All you need, is a little 6" slim taper file, and magnifying visor. Even then, when i file a tooth, i place my left thumb-nail against the file before moving over a tooth. I can nudge it into the next groove faster than hitting the next tooth by eye. I just file straight across, rather than ATB, and can't tell any difference.

Re: Multi tool/oscillating tool Questions.

#6

Re: I have the Bosch

Larry Clinton At Frankfort, (Central) Indiana

Lee, you might try the self adhesive rolls of abrasives from Klingspor - I don't have a multitool but use the abrasive for my Dremel profile sander. It is available in almost any grit size you could want and works as well or better than any abrasive I have used. I have a box of different grit rolls & cut the material to fit my unit. Very economical too, as it costs about 1/10 or less than the replacement sleeves sold by Porter Cable and Dremel. I find the rolls great for using on hand sanding profile shaped and flatblocks as well. Note: I use the paper backed -

I think you can purchase it in self adhesive cloth backed as well. http://www.woodworkingshop.com/category.aspx?id=22&f5=PAPER

Re: Multi tool/oscillating tool Questions.

#7

Harbor Freight

George Colonel's Workshop-Havertown PA

Good Afternoon Barry,

I have a Dremel, and it does get hot. My #3 son had a Dremel, which fell apart on the job. The design and plastic on the nose of the tool was not up to contractors' work. Instead, he had me buy a Harbor Freight, the best of the price range they had available. More amperage too. Cheaper blades. He likes it very much, and has had it for over a year. My next machine will be the Harbor Freight.

George

Re: Multi tool/oscillating tool Questions.

#8

Re: Bosch Multitool

Chuck Hans

Barry I have the Bosch variable speed, that I purchased from CPO tools that is a refurbished tool, and it works great, It came complete with all the accessories and a soft case. It was $89.00 and I have no complaints. It came with the adapter that accepts other blades as well. I got the corded model, because I prefer corded tools for the most part. I have a couple of other Bosch refurbished tools that I have had for a few years that have preformed flawlessly.

Re: Multi tool/oscillating tool Questions.

#9

Re: I have the Bosch

Yonak

Larry, what do you use to cut it ?

Re: Multi tool/oscillating tool Questions.

#10

David Barnett

(Message Deleted by Poster)


Re: Multi tool/oscillating tool Questions.

#11

Re: Since I saw this before Larry...

Barry Irby

I have not tried it, but I have read you can cut sand paper with an old pretty much used up bandsaw blade. Even a stack of it. So stack up some and cut a bunch at one time, If you have a band saw. (If you have a bandsaw, you surely have a trash blade.

Re: Multi tool/oscillating tool Questions.

#12

I resharpen too....

Barry Irby

I bought this multi tool on a whim and then found dozens of uses for it. Its MUCH more useful than I imagined. Cuts drywall like butter. But, drywall seems to be hard on the blades. Bought a little set of files from HF and use them. Actually do it by feel more than by sight. Most any raggedy snaggled toothed piece of metal will cut drywall if you vibrate it fast enough.

Just bought some blades at a craft show that are fine toothed and coated with TiN for cutting steel. They work well. That's why I was concerned about using Brand X blades.

The Bosch tool mentions an adapter plate bot does not include it.

Re: Multi tool/oscillating tool Questions.

#13

David Barnett

(Message Deleted by Poster)


Re: Multi tool/oscillating tool Questions.

#14

Re: Old pair of sewing scissors

Larry Clinton At Frankfort, (Central) Indiana

I have an old pair of Wiss scissors I picked up at an auction in a box full of junk. Good steel, I do run a stone or my diamond sharpener cross them once in a while - still cuts the sandpaper well after using them for a few years.

Re: Multi tool/oscillating tool Questions.

#15

Am I the only one......?

Barry Irby

that finds the fact that the tools (And other stuff) are now labeled in two or thee languages and they still don't say anything, Irritating? They have enough room on the package to tell you what you need to know, but they choose to tell you much less, but do it in three languages. Great, now you can feel like an idiot in the language of your choice. Oddly, Bosch is a German Company (I think), but the three languages are English, French and Spanish.

I thought it interesting that the tool I was looking at came with 21 "accessories". 15 of them are pieces of sandpaper. Little pieces about the area of a playing card.

Apparently the adapter plate is sold separately. There is a picture of it and its labeled in three languages, but does not say included of even "Purchased Separately". Probably not enough room to translate Purchased Separately into three languages.

Re: Multi tool/oscillating tool Questions.

#16

Re: Again, always something new to learn

Barry Irby

The guys on the Turning board often discuss buying large (1 meter square) sheets of H&L sandpaper from somebody like Industrial Abrasives or Klingspor and stacking the various grits and cutting them into hundreds of squares or perhaps hexagons and using them on two or three inch mandrels for sanding stuff on the lathe. I think there is an article on it.

Re: Multi tool/oscillating tool Questions.

#17

David Barnett

Cool idea. I'll search. Thanks!


Re: Multi tool/oscillating tool Questions.

#18

Re: Harbor Freight

Jason Waters

I keep a harbor freight one at my moms to do repairs there. It uses the allen bolt to hold the blade on. It has the cupped washer, and it works loose after a while, I have to keep tightening it. It works fine otherwise.

I like the Fein I have at home much better but it's pricey. I got mine on sale pretty decent on a clearance. The Bosch and Dremel both work too from friends that have them. that's where I would look if I was doing homeowner stuff.

Re: Multi tool/oscillating tool Questions.

#19

Re: Multi tool/oscillating tool Questions.

Barry Irby

I bought the corded version of the Bosch tool. So far I am very pleased. It is much more powerful that the battery version. The quick change feature for the blades is much easier than the other one that uses and Allen wrench. Makes it a snap to change the blades. So far I would highly recommend it.