Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Price drop on over 1300 Rockler items

WC Weekend Accomplishments.....

Posts

WC Weekend Accomplishments.....

#1

WC Weekend Accomplishments.....

Dennis E Peacock

25 June 2012

Good Morning Everyone,

Well...it's been hot and extremely dry here. We could really use some rain. No matter how much I water, it just doesn't seem to do any good....so if some of you folks that are getting plenty of rain could send some my way? I'd greatly appreciate it. :)

Well, I worked for the day job this weekend and I managed to have some time to get my 2 sons to help me with cleaning up 2 bays of my shop. We worked all afternoon Saturday and got the cleaning done for a great first attempt of cleaning up the shop. I have a project or 2 that I need to get busy with but I have to get my shop cleaned up first.

That's it for me, so what did YOU do this past weekend?

Best of weeks to you all.

Dennis Peacock

Re: WC Weekend Accomplishments.....

#2

Re: Shellaced New TV Table

George Colonel's Workshop-Havertown PA

Good Afternoon Dennis,

It was blistering hot and not a good time to try shellac on the new TV table. The shellac blistered, and I decided to finish it off in the basement shop, where it is out of direct sunlight and nicely cool. SWMBO and I did a bit of gardening. She does the stooping and bending which I can't do anymore. We harvested a bunch of radishes, cucumbers, a green bell pepper, and one patio tomato. Planning a Greek salad for dinner. Swmbo left for the shore on Saturday PM for a week by the beach, leaving me to fend for myself, amid peace and quiet. I do a lot of finishing this coming week, and maybe some lathe work. Haven't turned that tool on in many months.

Have a great week Dennis, and maybe you'll get some rain out of that storm in the Gulf.

George

Re: WC Weekend Accomplishments.....

#3

Alan Young

Re: WC Weekend Accomplishments.....

Alan Young

I spent my weekend working on our bathroom remodeling project. It was march when my son-in-law helped me gut the old plumbing and run new pex lines through the entire house. Since then the bath room project has remained idle as I have been swamped with commission work-no complaints about that! But we have family coming in a few weeks so it was time to get back to work in the bathroom. My son-O'Neill helped earlier in the week to finish off some wiring, then we removed the toilet and installed sub-flooring-


O'Neill kept a "Map" of all the plumbing lines so we wouldn't nail/screw through the Pex lines..


After 2 layers of subfloor we installed two pieces of green board then temporarily re-installed the toilet. A new one will be installed after the tile floor goes down later.


This weekend I was working by myself and got the window framing done-



The house was built @1895 so there was no insulation in the wall. I took the opportunity to add some be fore the drywall went up...



Thought I might need the Teletower but I was able to get it all done from the inside.



Re: WC Weekend Accomplishments.....

#4

Re: WC Weekend Accomplishments.....

Gary Smyth

Luck this weekend. Was given a decade old Weslo variable speed treadmill with a separate tread lift motor and fewer than 20 hours on it. Also found a table with these legs made from a full 6" blank. The top was wrecked as were two (of four) chairs. I had to disassemble it at the curb but hey, they are nice turned legs.

I also found this heavy duty muscle puller. I believe it is either a thread restorer or perhaps a full blown thread cutter. Either way, I have not seen this tool before - Made by Z-C, Jackson, Mich., 11" long, weighs a tad over 2lb. Thread sizes 1 1/4 x 12, 1 1/8 x 12, 1 x 14, 7/8 x 1?, 3/4 x 16, and 5/8 x 18. Anyone know what this is for sure? What industry made for? (No, it's not for measuring spaghetti portions.

Re: WC Weekend Accomplishments.....

#5

Ellis Walentine

Maybe a thread chaser?


Re: WC Weekend Accomplishments.....

#6

Re: WC Weekend Accomplishments.....

Larry in nw ohio

Gary We had something very simular when I was working and I always thought it was to hold a bolt by the threads so a person could thread the other end. Just put the bolt in the right threaded hole and clamp it, put it in a vise and thread it. It worked well that way for us. Larry

Re: WC Weekend Accomplishments.....

#7

Re: Maybe a thread chaser?

Joseph Mulherin, Sr

That is exactly what it is...thread chaser.

During my 35yrs in pipefitting/plumbing

I have seen and used such a tool many times.

Re: WC Weekend Accomplishments.....

#8

Re: WC Weekend Accomplishments.....

Gary Smyth

Sounds good. The thread sizes are bolt and not pipe standards. Holding by the threads makes sense if you think about it. I didn't know such a thing existed. Thanks