Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

knee surgery planned

Posts

knee surgery planned

#1

knee surgery planned

Joseph Mulherin, Sr.

Went to my VA emergency room on Friday and the doctor suggested I go see the Orthopedic doctor for possible surgery on my left knee. Seems that the miniscus might have to be cleaned out or some ligament damage repaired. So, shall be putting my woodworking aside for a while.

I have the Shopsmith 11"' band saw, and sat and looked at the housing...figured out how to make and add a riser block to it to increase the height of my cuts. Just a wooden block cut on angles to fit the inside of the housing and just screw it to the remaining pieces. Figure on raising the upper blade wheel about 5" to give me at least an 11" cut.

Should work, then figure out the length of blade I shall be using.

Have most of the chair parts cut out on present band saw setup, but have the need to cut the headrest at 8" while forming it.

Re: knee surgery planned

#2

Ellis Walentine

Re: knee surgery planned

Ellis Walentine

Good luck with the procedure, Joe. And with the new resaw capacity. With the right blade and feed speed, it oughta work. Might need some fine tuning to the guides, guards, etc.

Ellis

Re: knee surgery planned

#3

Re: knee surgery planned

Joseph Mulherin, Sr.

Yes, Ellis the guides and blade guard will have to be lengthened.

Shopsmith does sell anything like that, so I am going to design it myself and have it done at a metal shop. At present the guide only extends down from 6" to 1" at the table. Have to cut the curvature on the headrest 1 1/4" thk x 8" high, then round over as needed to about 7 1/4" . Headrest boards, 6 of them, are cut with a 4 deg bevel, then glued together; drilled for the back stantions bolts.

But before that the headrest must be bandsawn to 1 1/4" curvature across the rest.

This chair is really a good project for me...keeps me interested, busy, and active....in my 78yrs of age.....need that much....don't want to vegetate away...LOL 6 chairs are definetely planned....maybe more if the body stays healthy.

Re: knee surgery planned

#4

Re: knee surgery planned

Howard Norman

I had three knee surgeries done over the years before both knees had to be replaced about ten years ago. Two were successful and one was a failure. My orthopedic guy said that was about the correct ratio ten years ago, about 67% success. Good luck.

Re: knee surgery planned

#5

Good luck with both projects.


Re: knee surgery planned

#6

Re: knee surgery planned

George Colonel's Workshop-Havertown PA

Good Afternoon Joe,

Knee surgery isn't pleasant no matter the age. I have a couple friends who have new knees and hips, and they all seemed to work okay. One friend requires lengthy therapy for his hip stiffness--but its live-with-able, having no appreciable effect on his mobility. His 12" Sears bandsaw has old fashioned cast iron but lacks a riser block. He uses mine for resaw, and I buy the blades. Suchadeal!

George.

Re: knee surgery planned

#7

Re: knee surgery planned

Joseph Mulherin, Sr.

Thank you, George, I have done my search on the ways and means about the knee surgerys and will be seeing the doctor tomorrow morning. The inside of the knee is tender above and below the knee joint, and the ER doctor said that is because the miscus needs cleaning out and if the cartlidge is in need of repair they will do that then when the date of the surgery is set.

I have always been healthy in my younger yrs and was not ever so sick I could do what was needed in my workings in const.... except for that yr when my back disc went out and even then I was only down for a couple weeks.

I took up the woodworking when mny two sons were in the shop class in high school, bought the Shopsmith in 1978 and have made many pieces of furniture and other items over the yrs. These chairs are a blessing for me to keep active and make something for my family members to remember me by when I am gone.... but not for many yrs(am aiming for 120.....LOL)

Re: knee surgery planned

#8

Re: knee surgery planned

Joanne in Point Pleasant, PA

Joseph, good luck with the surgery on the knee and on the bandsaw. I added the riser block available for my Delta bandsaw. Makes resawing much easier. You might consider designing yours so that a standard length blade readily available will fit. Let us know how your surgery goes and when you get to the saw, post some pics.

Re: knee surgery planned

#9

Re: knee surgery planned

Joseph Mulherin, Sr.

Joianne, I am still puzzling around about sending out pictures of my work. I take the pics, transfer them to the computer, but get lost in trying to use the pic resizing programs so I can send just up to the 100mb allowed here on WC.

I cut the block using some hardwood I had and made the cuts so it will fit into the space I chose to install it. Figured a 4" rise, but you are correct in that I should make the block so I can use already available blades. Am figuring on the 98" blade, but I can cut other blocks to install to get the correct space to fit the chosen blade.

Re: knee surgery planned

#10

Re: knee surgery planned

Joseph Mulherin, Sr.

Went to VA hospital and they said I was not on the schedule to see the Orthopedic doctor until July 30th....I was never told that at the ER meeting.

So, have an appt then and Urology doctor on the Aug. 9th.

Hey, it is getting to be hell just getting by as I get older.....lol

Got a shot or Demerol in knee and it does seem to allieve the pain I was having.

Am thinking if it does this for me I might just opt out to have more shots as time progresses instead of having surgery.

Re: knee surgery planned

#11

Re: knee surgery planned

Joseph Mulherin, Sr.

Am working on my Hal Taylor chair....gradually.

bought some more Alder and some oak for the rocker bottoms. Am cutting them as slats 1/8-3/16" thk and 1 5/8" wide to be used glued up together to make the rockers...2 oak, 2 alders, 1 poplar for contrast, then 5 more layers of alder on top before bending onto the forms and holding for about 3 daqys till glue totally cures.... same as with the back braces. Have cut the arms, the rear stantion/legs, the front legs, have to do the seat dado process yet and cut the holes for the legs to fit into and glue up.

Am taking pictures all along, but do not yet feel good about the process of the sending out using the re-sizer programs....dummy me. Probably expect chair to be finished sometime in late July. Then start on second chair for 2nd son.

Want to have them ready for Xmas gifts. And about 4 more chairs to other relatives eventually.

Re: knee surgery planned

#12

I have had both kneed done by

Keith Newton

Orthoscopie, and the results was instant relief. Back when I was active in the sailing club, the knee doc, offered me a deal, if my insurance would let him do it in his office. After watching the procedure on TV while he was in there, later he noticed later, as we were standing around talking, that I was standing, favoring the leg he had just done, rather than the other.

I couldn't wait to get the other done. It is hard to maintain a good level of fitness, when having to deal with a lot of pain.

Re: knee surgery planned

#13

Re: I have had both kneed done by

Joseph Mulherin, Sr

Thank you, Keith, I am seeing the doctor on July 30th and

then we shall decide just what is going to be done. Got the shot in my Knee joint Tuesday and it does feel better right now. Doctor who injected it said the effect would probably last for 2 months.

This morning, Wednesday, I feel just right with no pains in leg at knee or muscle above and below the knee. Am just going to be doing some minor work on my chair, maybe glue up the rockers, but nothing else. Have most of the parts cut out and ready to machine to finish needed for headrest, arms, and legs, just have to dado seat contour on table saw and then use angle grinder and sand to finish contour of seat; drill the holes in the seat and headrest for the back slat braces then assemble everything.....probably in late July I anticipate being finished with the first chair....5 more planned.