Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

Curly Arbutus (Madrone) Dining table

Posts

Curly Arbutus (Madrone) Dining table

#1

Curly Arbutus (Madrone) Dining table

HC Sakman

Hi Everyone...

I know, I've been away from here for a while, despite a few attempts to come back but did not happen as planned, so just excuse me for that.

This rare (to me) heavily curly figured arbutus boards came from our local wood recovery program that have been ran by our local guild - WWW.VIWG.COM - from a few years back, at least 4~5 years as I recall.

As some of you may already know, drying/seasoning arbutus is very challenging as it is highly unstable during this process. Sure enough, most of these heavily figured boards were honeycombed. (checks in the middle of the board, either just below the surface or all the way through over the thickness of the board.) Anyway, I managed to use 3 boards to make this table.


Design is mine with collaboration with my clients, who were instantly fell in love with this wood as soon as I rubbed some paint thinner on it. In its trestle base, there are many compound angles, joined with tenons and loose tenons, as well as the wedged through tenons.


For the top, veneers (over Baltic birch plywood) were resawn, then sanded to 3/32" thickness. All the edges are 3" wide and 2-1/8" thick. rest of the table is made out all all solid wood.


Top has been gradually sanded to 1000 grit and finished with many, many coats of hand rubbed varnish. (my mix)


Just as a nice finishing touch, thicker than the center edges were bevelled towards the cneter plywood base as seen in the last picture.


Thanks for viewing and feel free to shoot any questions you may have.

Chico

www.sakmanfinewoodworks.com

Re: Curly Arbutus (Madrone) Dining table

#2

All I can say is

Dustmaker Mike

Wow.

Re: Curly Arbutus (Madrone) Dining table

#3

Re: All I can say is

Larry in nw ohio

What else is there to say. Larry

Re: Curly Arbutus (Madrone) Dining table

#4

Stunning!!!


Re: Curly Arbutus (Madrone) Dining table

#5

Re: Curly Arbutus (Madrone) Dining table

Keith Newton

That is a fine looking table, and you did a very good job making it.

My only concern, is your choice of using BB for the substrate for this thick veneer. You are putting a lot of faith in the first glue line under the face veneer, even if you did a perfect job gluing this veneer down. Plywood manufacturers try to walk the fine line between using too much, and too little, and may only need a 70% bond to hold that a thin birch face on. But now you have chosen to add what might be the most unstable wood growing in America on top of that face.

Im not saying there will be a problem, and I hope I'm not causing you a lot of angst, but that is not the way I would have done it. Did you saw the veneers yourself?

That is a nice looking piece, and will make a nice addition to a lot of great work on your website.

Re: Curly Arbutus (Madrone) Dining table

#6

Wood Recovery?

Thomas Skaggs, Foothills of Mount Level

Gosh....that's my kind of recovery! With wood that beautifully figured you did a great job of simple lines design to let that wood really make a statement.

As always Chico....Great!

Re: Curly Arbutus (Madrone) Dining table

#7

Re: Curly Arbutus (Madrone) Dining table

Mark Valsi

WAY TO GO CHICO !!!

another stunning masterpiece from the gifted hands of CHICO !!!!!!

I just wish you would post more more more more more more . . .

Great job, as usual !!

Re: Curly Arbutus (Madrone) Dining table

#8

Re: Curly Arbutus (Madrone) Dining table

Nick Tuzzolino

Hi Chico: You continue to outdo yourself and amaze everyone. Good to hear from you again. Beautiful!!

Nick

Re: Curly Arbutus (Madrone) Dining table

#9

Re: Curly Arbutus (Madrone) Dining table

Lynn Baker from sunny Glacier, WA

Great Design and execution as usual Chico. Those of us familiar with the Arbutus (Madrona) realize how challenging it can be to work with.

It's really good to hear from you again.

Lynn

Re: Curly Arbutus (Madrone) Dining table

#10

Re: Curly Arbutus (Madrone) Dining table

Nelson

Don't see a problem but how would you have done it Keith?

Re: Curly Arbutus (Madrone) Dining table

#11

Re: Curly Arbutus (Madrone) Dining table

George Colonel's Workshop-Havertown PA

Goood Morning Chico,

That raises the bar again on plannng and execution and sheer craftsmanship. What a pleasure to look at. I am curious about the degree of waste you had to suffer to yield so lovely a piece. Also, what are the dimensions of the table and the size of the three boards you used?

Another mnagnificent job!. Glad to have you back.

George

Re: Curly Arbutus (Madrone) Dining table

#12

Re: Curly Arbutus (Madrone) Dining table

Keith Newton

I probably would have used the plywood on the bottom, with 1/2" mdf, or considering the properties of this wood, industrial PB on top of that to veneer onto.

But let me state, I have never used any of that wood. However, I recall from back when seeing Christian Bruchard's fantastic thin walled hollow turnings, which took on wonderful distorted shapes, I recall studying the properties. I think I recall it has about the highest ratio between tangential / radial contraction of any domestic wood plus pretty high strength numbers in the other aspects. I was hoping to find something growing in my area that would do that. The closest thing I recall was Shagbark Hickory, but I've never seen a burl on one, nor gotten my hands on any of that even.

However those guys out West who use this wood all the time, probably do this all the time, and never have a problem with it.

Re: Curly Arbutus (Madrone) Dining table

#13

HELP!!!

Stuart Hough

Someone call an ambulance! I think I just broke my jaw on my desk when it dropped out of joint as I looked at this stunning table!

Great work, Chico!

Re: Curly Arbutus (Madrone) Dining table

#14

So what do I have to do...

Sophie

To make Becky like my stuff and not want to buy yours??? ;-)

I'm on a borrowed computer so send me an email with your new number please.

Sophie in Jackson Hole Wy with no 5th gear in the truck.

Re: Curly Arbutus (Madrone) Dining table

#15

Re: Curly Arbutus (Madrone) Dining table

Mark Mandell - Gone Round In New Jersey

Good design, beautifully executed, Chico. I take it the drum sander got a workout with all that curl. ;) I tried varnish on "use" tables. Got tired of the bring-backs. I like finishing, but don't want to make a career out of it. Good luck with this one.

Re: Curly Arbutus (Madrone) Dining table

#16

Sophieeeee.....!!!

HC Sakman

You email me please since you have no email here! Say Hi and kisses to Becky!

Re: Curly Arbutus (Madrone) Dining table

#17

Question

Bill Tindall

I can well imagine the new owners are well pleased with the result. It certainly won't escape attention at the dinner party. Not familiar with the wood but it made up nice.

I have a question about "framing" a central plywood assembly with a frame of solid wood. How do the solid wood frame pieces attach to the plywood panel?

Re: Curly Arbutus (Madrone) Dining table

#18

Answers?

Mark Mandell - Gone Round In New Jersey

t&g, splines, biscuits, loose tenons, haunched m&t

But you know all that ;)

Re: Curly Arbutus (Madrone) Dining table

#19

Ellis Walentine

Question about beveled edges

Ellis Walentine

... the interior ones, that is. It appears that the finish table is flat, so does this mean those inside bevels were made the thickness of the face veneer and that the veneer was beveled to match? I'm trying to comprehend why you would have done it this way. And how did you handle the inside corners without mason's miters on the edging?

Thanks for checking in, Chico. I always admire your work. Wonderful wood.

Cheers,

Ellis

Re: Curly Arbutus (Madrone) Dining table

#20

Since we are asking about construction......

Dick Coers

why no balancing veneer on the bottom of the plywood? Or is that a before picture? I've been taught, and always agree with the idea, that all veneer work has to have balanced numbers of veneer to stay flat.

Re: Curly Arbutus (Madrone) Dining table

#21

One of them gotta be right...

HC Sakman

Splines were used.

Re: Curly Arbutus (Madrone) Dining table

#22

ALL THE ANSWERS

HC Sakman

Thanks Ellis,

Long edges and the veneers on the center all came from one very wide board (I think it was 13~14 inches wide by almost 3" thick) the reason I used 15 degree bevel on top and 45 degree on the bottom of the outer edges was to reduce the thickness to balance with the base. Otherwise top was going to look too heavy and/or thick.

I applied the 3/32" thick veneers (shop sawn and sanded) on torsion box that I made, using 2 layers of 1/2" EUROPLY and 3/4" strips in between (in the veneer press) which is Baltic birch plywood but it comes in 4x8 size insted of 6x6.

Under the table, I didn't want a sharp transition (or joint) from the edges to the thinner plywood torsion box or "center", which is just over 1-3/4" thick vs. 2-1/4" thick solid edges. So, I used a 60 (or 30 I guess) degree bevel for smooth transition to the center when hands would probably caress the under the solid edges. This table top's finish was one of the best hand rubbed varnish I've ever done. All surfaces feel like glass, including bottom of the edges and sides. It begs to be touched and felt. So, that's the reason for bottom inner bevel, which was done with a sharp point 30 degree router bit and edge fence. Corners were done with skew chisels.

Hopefully this wood will not move anymore. It usually stabilizes once fully dry, though it was not kiln dried but air dried. So, fingers crossed.

Chico

Re: Curly Arbutus (Madrone) Dining table

#23

The Proverbial Shotgun Answer

Mark Mandell - Gone Round In New Jersey

Fire the full spread and you gotta hit something besides the barn :D :D

Re: Curly Arbutus (Madrone) Dining table

#24

Re: Curly Arbutus (Madrone) Dining table

HC Sakman

I've done this application many, many times within the last 15 years. I don't know what kind of Baltic birch ply you have encountered before but I never ever had a problem with delamination in any level with this plywood. Ah, if you were talking about any Chinese made plywood, then I agree and I'd not touch that with a ten foot pole even if it was $10 a sheet.

Thanks.

Chico

Re: Curly Arbutus (Madrone) Dining table

#25

Ellis Walentine

Thanks, Chico. It all makes sense now.