Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

The I-BOX is here! *LINK*

Posts

The I-BOX is here! *LINK*

#1

The I-BOX is here! *LINK*

Alan in Little Washington (NC)

I hope this post is OK. The product will eventually be sold by two or more WoodCentral advertisers.

As I might have mentioned in posts here, quite awhile ago I came up with a new box joint jig mechanism that I thought was a significant improvement over any retail or DIY jig available. I built a prototype that worked flawlessly and decided to attempt to market it. I eventually licensed the concept to INCRA and we have worked together for almost three years to improve and refine my original design and make it manufacturable. It took much longer than I had ever imagined, but I think the results were worth the wait. INCRA did a fantastic job and it is finally here! :) :)

The listing was not supposed go active until Monday and the official rollout is not scheduled until INCRA sends out their email broadcast on Wednesday, June 16th, but check out "What's New?" About halfway down in the right-hand column on INCRA's Incremental Tools website.

Clicking on "What's New?" takes you to the product page where there are details and a neat video of the INCRA "I-BOX."


img

Incremental Tools

Re: The I-BOX is here! *LINK*

#2

Re: The I-BOX is here!

bob murphy

Congratulations! Looks like a wonderful product. Thanks for posting.

Re: The I-BOX is here! *LINK*

#3

Re: The I-BOX is here!

Larry in nw ohio

Congratulations Alan. I`m very happy for you, and I hope the very best for you, that everything goes good for you. Hope you sell a million, and you make just as much. Do you remember when our family tree came out, that we are long lost kissing brothers. ;) Larry :D

Re: The I-BOX is here! *LINK*

#4

Got mine . . . maybe

Henry Higginbotham

Their web site accepted the order and sent me a confirmation, anyway, so maybe it's good to go now. We'll see. Thanks for letting us know, Alan!

Re: The I-BOX is here! *LINK*

#5

Good try, Larry .. very impressive.


Re: The I-BOX is here! *LINK*

#6

Re: The I-BOX is here!

Alan in Little Washington (NC)

I guess you haven't researched typical license fees! :D :D

Re: The I-BOX is here! *LINK*

#7

Re: The I-BOX is here!

Gary Smyth

Alan,

Good on you. I was surprised however when I viewed the adjustable spacing mechanism. Incra no doubt is more accurate, clearly made with precision parts, and less subject to vibration, but it reminds me eerily of the "Shop Notes" box joint adjustment jig of several years ago. I don't have the issue, but I built the (my version of the) jig. The spacers on mine are hardware store "L" brackets. Hope you do well with it. Incra seems the right company with which to partner.

Re: The I-BOX is here! *LINK*

#8

Re: The I-BOX is here!

Alan in Little Washington (NC)

Thanks!

On first look, the I-BOX might appear similar to the Shopnotes adjustable jig and its retail cousin the Woodsmith Aluminum jig, but the construction and operation of the I-BOX is different in some very significant and specific ways.

Setting the I-BOX only requires turning one knob which is connected to its unique positioning engine and a specially designed and precision machined leadscrew. Even the design of the guide pins is important. The I-BOX and Woodsmith/Shopnotes jig both use a kerf to set the pin width, but with the Woodsmith/Shopnotes jig you must turn a second, independent all-thread rod leadscrew to change the blade-to-pin spacing. It is up to you how you determine if it is right- you must manually set it using calipers, trial and error, or some other method not clearly explained in the minimal directions. When you set the split guide pin width the I-BOX positioning engine automatically and precisely sets the proper blade-to-pin spacing AT THE SAME TIME!

The I-BOX excels in all other categories as well- is self-supporting with its own adjustable miter bar (a miter gauge is not needed), inexpensive,user-fabricated replacement backers, blade guards, single mechanism lock, anti-backlash design, etc., etc., etc.

And by the way the here is a photo of the I-BOX's humble beginnings. Note the single adjustment knob (the magic is hidden inside the wood blocks):


Re: The I-BOX is here! *LINK*

#9

Re: The I-BOX is here!

Joe W

Will the I BOX work on their router as well or is it meant to be a table saw only jig? Congratulations and good luck on its success.

Re: The I-BOX is here! *LINK*

#10

That is really cool Allen

John in NM

Congrats on the invention!

Re: The I-BOX is here! *LINK*

#11

Re: The I-BOX is here!

Alan in Little Washington (NC)

Router table or tablesaw.

Re: The I-BOX is here! *LINK*

#12

Re: The I-BOX is here!

Brian in SLO

Another one just flew out the door!