Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

Back from handtool land - Shop layout question

Posts

Back from handtool land - Shop layout question

#1

Back from handtool land - Shop layout question

Guillaume Dery

Hi gang, another foray over from hand-tool land. I am finally at the point where I am laying in my electrical in my workshop (see attached plan).The 120V plugs are all installed (orange circuits) 2 20A split circuit runs leapfrogging around the room, outlet at every 4 feet. The current plan is to put my lumber rack next to the door and the jointer/planer on the opposite wall. I just want to sanity check this layout with folks as the jointer planer is the only 30A circuit in the place and once it is in, I am committed. Thoughts, advice, etc. welcome and sought!


Re: Back from handtool land - Shop layout question

#2

JL

Re: Back from handtool land - Shop layout question

JL

The following thoughts.

Task lighting - I have a number of task lights in certain areas of my shop. Most notably my lathe and my work bench. Those are where I need task lights that I can aim/focus at my work. I can turn off all of the lights in my shop and leave the task lights on for those areas. They actually provide enough illumination to work decently. As your eyes grow older (bifocals, etc.), you sometimes need better illumination.

Circuits at a higher level - I have a circuit that is near my ceiling. I use it for my air filtration. I realize that as a hand tool person, you may not always use sanders and or sandpaper. You may just use a cabinet scraper and planes. Consider a circuit up high for air filtration.

Re: Back from handtool land - Shop layout question

#3

Re: Back from handtool land - Shop layout question

Henry (Raleigh NC)

A minor detail - but my shop was laid out (not by me) with outlets just below 4'. Sheet goods are very effective at blocking multiple outlets. If you are going to put outlets at mid-wall level, put them just above 4' rather than just below. You may not work much with sheet goods, but the next owner might!

Henry

Re: Back from handtool land - Shop layout question

#4

Re: Back from handtool land - Shop layout question

Guillaume Dery

That's a good point. off the top of your head, do you know how much a typical overhead filtration unit draws? I am wondering if I should wire separate or if I can just draw off the light circuit.

As for task lighting, I was planning on using the plugs I have space every 4' on the walls. There will definitely be some because my eyes aren't what they used to be!

Re: Back from handtool land - Shop layout question

#5

Re: Back from handtool land - Shop layout question

Guillaume Dery

Already done. All the split outlets you see (the 2 orange circuits) are already in and the bottom of the boxes is at 50".

Although not a fan of sheet goods. They are flat and the most efficient thing for getting things like built-ins off the honey-do list...

Still trying to figure out if my placement of the jointer/planer is optimal

Re: Back from handtool land - Shop layout question

#6

Re: Back from handtool land - Shop layout question

Robin Corell in Atascadero CA

Generaly speaking you never want anything on the same circut as your lights, that way if something pops the breaker you wont be standing there in the dark with a sharp blade still spinning.

As for your shop lay out it really comes down to how you work. In my shop I use only 8/4 rough sawn wood so I use my planer a lot, but I tend to use my 16" disc sander to flaten boards more often than my jointer. So in my shop the jointer is shoved in the back of the shop.

For power all my circuts are 20A except my table saw. I have a very small shop with only four 110v circuts and one of those is lights only. I have four 4 way boxes and each has a duplex on a sperate circut. Even so I do have several tools on each circut that total more amps than that circut will handle, but as a one man shop I can only use one at a time so realisticly it is not a problem.

If I was designing a shop from scratch I would lay out the circuts such that I could have every tool in the shop running at the same time if I wanted to. I would also consider having more 220v outlets and since I like vintage iron I would love to have the option of 3ph power just incase I ever pick up an aircraft carrier (AKA a 24 jointer)

Robin

Re: Back from handtool land - Shop layout question

#7

JL

Re: Back from handtool land - Shop layout question

JL

Overhead filtration units don't draw very much current. They might have a 1/5 hp or 1/4 hp fan motor. So a 15 amp circuit would be adequate. But as you have 20 amp breakers, use those.

Robin's point is well taken. I've got four 20 amp circuits in my shop for my walls.

I have two circuits per wall. The opposing walls have the same circuits.

I put in track lighting in my shop - but that is what worked for me. I have fixtures which take PAR30 bulbs. The light from the bulbs is "focused" on the work. My general lighting is fluorescent fixtures. My track lighting is switched and on separate circuits from all of the tools and the general lighting.

Re: Back from handtool land - Shop layout question

#8

Re: Back from handtool land - Shop layout question

AZ in Colorado Springs

Your plan looks reasonable. You want to ensure there's adequate infeed & outfeed space for long pieces of stock, and it appears that your outlets will be placed about midway along the wall. Without seeing the placement of work benches and other items, there's little to comment on. Of course, if your other tools and workbench are mobile, then you can easily make room. (My shop is in a 2 car garage, and it's been so much easier since I've gotten mobile bases for my table saw & band saw and put wheels under my work bench.)

AZ

Re: Back from handtool land - Shop layout question

#9

Re: Back from handtool land - Shop layout question

Jason Waters

On your 220V 20 A circuits, if one is a dust collector or cyclone, it should be dedicated as it will need to operate at the same time as another 220V tool.

Also, you may not be able to wire more than one 220V outlet per breaker, please check the code(s) on this. Mine's not done this way, and I think I asked about doing it how you proposed, and was told no. Or it might have been something like "I wouldn't suggest doing that", and not wanting problems, I avoided it.

Re: Back from handtool land - Shop layout question

#10

My situation relative to the question

Bill Tindall

Let me begin by saying that I don't understand the drawing so the following may be irrelevant. Also, my jointer is just a jointer so this difference may color my experience.

I find that having the jointer near the table saw is ideal for my work flow. It is all about work flow.

Rough lumber comes out of the lumber rack

Lumber gets broken down to rough cut lengths.

These cuts get one side flattened on jointer, then edged on the jointer then ripped to widths, then maybe jointed again, then planed to thickness. The table saw is handy place to pile stuff to be jointed and the jointer a handy place to pile stuff to be ripped. Bottom line, I want these machines next to one another. Your results may differ.

Planer- I occasionally plane something 16' long and joint something up to that length. To do so I need to aim the outfeed out an entry door. This fact located the jointer, table saw and planer.

Re: Back from handtool land - Shop layout question

#11

Small point about Overheads

Marvin Horn

DAMMHIKT- But if you criss-cross the wiring on your overheads you can often leave half the lights off. It can be a real energy saver.

Re: Back from handtool land - Shop layout question

#12

Kneale Brownson

Re: Back from handtool land - Shop layout question

Kneale Brownson

Is the planer/jointer on wheels? The middle of a 17-foot wall will limit length of wood to 8 feet unless you've got room to swing it a bit. If you can roll it out to the middle of the 25-foot wall, you're ok. I have both my planer and jointer located to handle stuff up to about 16 feet long.

Re: Back from handtool land - Shop layout question

#13

Re: My situation relative to the question

Guillaume Dery

OK, I gotta ask. Is everyone on this board building arks as a hobby?

You are not the first to mention planing or jointing 16 feet. I can honestly say in all my years, I never needed that much length and I have built some fairly large pieces. 6 to 8 feet is usually the longest I need. That being said, I think I may switch walls so that I can open the doors and use the hallway as extra infeed space when needed (also saves me some wiring :))

What all are you guys building that you need that much capacity????

Re: Back from handtool land - Shop layout question

#14

Re: Back from handtool land - Shop layout question

Guillaume Dery

There will be no problem running all the tools at once if needed. Code here in Ontario is kinda wonky and won't allow multiple 240V outlets on a circuit. The upshot of it is that in that 100A panel, I have:

9 2-pole 20A breakers (2 to feed my 120V split circuits which leapfrog each other every 4 feet and 7 to provide 240V outlets around the shop). Of the 240V outlets, 3 are spoken for: Tablesaw, Dust Collector and Bandsaw. This leaves 4 for moving tools around or new toy purchases.

1 2-pole 30A breaker to feed the jointer/planer

1 15A for shop lights

I think based on the input I have gotten here that I will add either a 15A or a 20A circuit for overhead plugs. Normally I would go 20A but I just ran out of 12-2 wire and still have about 100 meters of 14-2.

Re: Back from handtool land - Shop layout question

#15

Re: Back from handtool land - Shop layout question

Guillaume Dery

I hear you on the mobility issue. 2 shops ago, I was working in a 1car garage. That ensured that I put wheels on EVERYTHING!

Re: Back from handtool land - Shop layout question

#16

Re: Back from handtool land - Shop layout question

Guillaume Dery

It is indeed a wheeled beast. I have been toying with the idea of moving it next to the tablesaw in the middle of the floor as well but am still of 2 minds on that score.

Re: Back from handtool land - Shop layout question

#17

Re: Back from handtool land - Shop layout question

Guillaume Dery

Jason, all of my 220V outlets are on dedicated breakers (code here in Ontario). I think I just confused some because I used 2-pole 20A breakers to power split circuit receptacles at 110V (running 12-3 wire to get the 2 hots and 1 neutral)

Re: Back from handtool land - Shop layout question

#18

Re: Small point about Overheads

Guillaume Dery

That goes on my to-do list. I was going to wire 2 rows but criss-cross actually ends up with more even light distribution.

Thanks

Re: Back from handtool land - Shop layout question

#19

Architectural parts

Bill Tindall

The most recent example of needing some length was making some shoe molding for daughter's house. In the case of molding one wants it as long as the lumber available, in this case 14 1/2'. I have made 16' stair parts.

Indeed for furniture, I usually break down the lengths (I prefer to buy 12' packs of lumber, less waste and not overly long for handling) into rough cuttings at the start of construction. That said, I often skip plane these 12' long pieces before breaking them down to smaller sizes, so 12' fore and aft of the planer is a must.

Re: Back from handtool land - Shop layout question

#20

Kneale Brownson

Re: Architectural parts

Kneale Brownson

Like Bill, my use of longer lumber would be for house trim parts mostly. I think the longest piece of furniture I've ever done was a 14-foot display case. I usually try to purchase longer rough lumber and usually break it down for projects.

Re: Back from handtool land - Shop layout question

#21

Re:One suggestion

Larry Clinton At Frankfort, (Central) Indiana

As I wish I had done - Now I would install a few outside receptacles (120V). I purchased some of the boxes then decided I didn't really need outside outlets. I often sand items outside of the shop in the summer, vacuum out my van etc. I now have to use extension cords. If I had it to do over, I would certainly install a couple outside.