Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Nearly 100 Exotic Wood Species, Direct-Imported Since 1972. Shop Slabs & Turning Stock.

Resawing Really Big Stuff

Posts

Resawing Really Big Stuff

#1

Resawing Really Big Stuff

Doug Reynolds in Seattle

I scored some really big walnut that is 6 to 8 feet long, 12 - 14 inches wide and, 3+ inches thick that I would like to resaw into 4/4 rough. The problem is no one side is already smooth and no way is this going to fit on my 6 inch jointer. Plus, each piece weighs at least 60 pounds which is a lot for a one man job. My bandsaw is a MiniMax 20 so, I think it will handle it.

I'd appreciate any suggestions on how to resaw stuff this big and heavy safely and, without breaking blades or my back.

Re: Resawing Really Big Stuff

#2

Re: Resawing Really Big Stuff

Robin Corell in Atascadero CA

I used my chain saw and alaskan mill to resaw a 30" wide slab and it worked exceptionaly well, other then the 3/8" kerf.

Re: Resawing Really Big Stuff

#3

Re: Find a local small sawmill...

Charlie Lenz

Or there is an accessory for circular saws called a Prazi. Basically it's a chainsaw bar that bolts up to a circular saw. If they have a setup for milling I don't know.

Re: Resawing Really Big Stuff

#4

Re: A Reynolds question

Charlie Lenz

Any relation to a Mike and Rick Reynolds that lived in Vancouver, Wash. in the mid 1970's ? Rick had a black 69 GTO that was pretty quick.

Re: Resawing Really Big Stuff

#5

Re: A Reynolds question

Doug Reynolds in Seattle

Charlie: Not that I know of.

Re: Resawing Really Big Stuff

#6

Is it for immediate use?

John in NM

I wait on resawing until I have a specific application that requires the thinner wood. In that way you can usually cut the wood to length before resawing and not have to cope with hugely long and heavy stuff. Obviously, if you're building an 8 foot long conference table, this isn't going to help much :D

Re: Resawing Really Big Stuff

#7

Re: Resawing Really Big Stuff

Chuck in Mtl.

i would reduce the width from 12-14 inches to a more manageable size such as 4-6 inches. Its rare that a board this wide is used for furniture and most often glue-ups are used. Then at the smaller width it can be resawn on your minimax into some nice boards.

Re: Resawing Really Big Stuff

#8

Good Suggestions

Mark Mandell - Gone Round In New Jersey

OTH, if you really want 8' boards and want to save waste, look up a WoodMizer or TimberKing owner in your area. their horizontal band mills might be able to get you 3 boards at 4/4 out of the stock you describe.

Personally, I'd hold the stock intact. 4,6,8/4 stock is easy to find at good yards, but 12+/4 is tough and quite expensive. I would hold it for leg stock rather than boards.

Re: Resawing Really Big Stuff

#9

Re: Resawing Really Big Stuff

Steve Schoene

I really wouldn't rip these distinctive wide boards down to mundane 6" widths. You may, depending on the styles of what you build you might rip off most of the sap wood.

Re: Resawing Really Big Stuff

#10

Bart Goldberg

Re: Resawing Really Big Stuff

Bart Goldberg

I would Plane it smooth on one side, if you have a planer that can handle 12-15 inch width. It may not be jointer flat, but can probably get you close. You can also build a sled from plywood to hold the board in place while planing it. Use shims under the spots where it may rock to keep it in position while planing on the sled. Use out feed rollers to distribute the weight on both indeed and out feed sides to keep it from stressing the planer bed.

My 2 cents

Bart

Re: Resawing Really Big Stuff

#11

Re: Resawing Really Big Stuff

Pat Evans

Flattening one side with a router is not difficult. A simple temporary box around the plank and an auxiliary router base that spans the box so the router covers the entire plank width works fine. I use a slot cutter bit to cover a wide path and just take small cuts at a pass.

Re: Resawing Really Big Stuff

#12

David Barnett

Yeah, I'd stall, but that's me

David Barnett

"I wait on resawing until I have a specific application that requires the thinner wood. In that way you can usually cut the wood to length before resawing and not have to cope with hugely long and heavy stuff."

That's the smart way to do it, I'd say. On the other hand, I'd need a compelling reason to turn 12/4 walnut into 4/4, given how difficult and expensive it is these days to find wide 12/4 boards. So much of my furniture starts with 12/4, even my workbench base and anvil stand started as 16/4 and 12/4 walnut. Just love it that thick. But if someone wants 4/4 boards, presumably matching ones, that's not for me to judge, but I would encourage waiting until the last possible moment to commit to resawing.

At any rate, you're right, John. It's hard to do without a helper. Most of my boards were 10' long and only up to 9" wide, and I gotta say, I wouldn't have wanted to even rip on my 16" bandsaw without help. An 8' resawing job on a 12"+ wide slab? Yikes.

Re: Resawing Really Big Stuff

#13

Re: Resawing Really Big Stuff

Dick Coers

You could look at the Laguna Timbermaster for ideas. I've seen homemade rigs that use a long piece of steel in the miter gage slot, and outrigger cabinets.

Re: Resawing Really Big Stuff

#14

Ellis Walentine

What you could do...

Ellis Walentine

If I really wanted to resaw 12/4 walnut -- which I probably wouldn't -- I know that my first choice would be to have it sawn for me on a small band mill. It would be the quick, most appropriate, cost-effective way to do it. Pop them in your truck, take them to the mill, zip zop, check please.

On the other hand, if you're itching to tackle this yourself, you can overcome the weight of these pieces by making infeed and outfeed tables for your bandsaw. You can overcome the awkwardness of holding them upright by making a long, right-angle traveling fence that you can screw to one face of the board. This has the advantage of being able to ride along a straight edge to give you a straight cut, regardless of whether the faces of your board have been planed flat.

It would be so much easier to have someone do it for you.

Ellis

Re: Resawing Really Big Stuff

#15

same here

Bill Tindall

Given the difficulty and expense of obtaining 12/4 walnut essential for some kinds of legs and other application I would be saving it for such needs....unless....I was wanting to book match the resawed boards.

Resawing something this big is a two person operation in any case.

Re: Resawing Really Big Stuff

#16

Re: same here

Barry Irby

I agree that this is an awkward job for an upright bandsaw in a one man shop. Taking it to a bandsaw mill would be faster easier, safer, and probably give you better results.

But, If I were near you, (I'm near Richmond, VA so there is a whole continent in between) I would trade you some 12 or 15" 4/4 walnut boards for them BF for BF and even throw in some extra. I have lots of 4/4 stock but am short on 12/4 stuff. Take a shot at trading with somebody. Low risk, everybody wins.

Re: Resawing Really Big Stuff

#17

Re: Resawing Really Big Stuff

Carol

Barry has a great idea. Check your email. How many board feet?