Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Bowling Alley Wood

Posts

Bowling Alley Wood

#1

Bowling Alley Wood

karl skutski

Don't ask why, but I now am the proud owner of a 10-foot section of a used bowling lane. It is 2 inches thick, pure maple. The lane, as I discovered, is actually made up of 1.1" strips of 2"-inch maple, with some type of gunk between the strips and something else that holds the boards together. I also discovered that when removed from the alley, the lane tends to curl up.

I think it would make a great workbench surface, but I am unsure how to cut it. I don't how the strips are joined, and what kind of saw I should use to make horizontal or vertical cuts. Does anyone know how the maple strips are joined? Also, what do I need to do to flatten out the curl?

Re: Bowling Alley Wood

#2

Re: Bowling Alley Wood

Dave Dircksen

I bought one a couple years ago, each strip is nailed. Mine had angle iron screwed to the bottom side. That keeps it flat.

Re: Bowling Alley Wood

#3

Re: Bowling Alley Wood

Joanne in Point Pleasant, PA

I have a piece waiting to be made into a bench, too. I think the strips are nailed together and there is a piece of angle iron, like Dave's. I bought a few junk blades to use to cut it with the circular saw when I am ready.

Re: Bowling Alley Wood

#4

Re: Bowling Alley Wood

karl skutski

Thanks, Dave. I want to cut it lengthwise. Guess that means I will be cutting through nails. What kind of blade do you recommend? I was able to split the strips apart with some wedges, but not sure if I could split the whole length, so I assume I will need to cut through nails.

Re: Bowling Alley Wood

#5

Re: Bowling Alley Wood

karl skutski

Thanks, Joanne. Mine didn't come with an angle iron. I want to cut it lengthwise and also take a foot off it. Any idea what blades I would use on my circular saw?

Re: Bowling Alley Wood

#6

JL

Re: Bowling Alley Wood

JL

Cheap blades. I would use a circular saw (with a 7 1/4" blade or so). Probably something with 24 teeth to 40 teeth. This would give you a reasonable end finish. I would buy a carbide tipped blade as opposed to just a steel blade. I would use a guide to make sure that your cut is square.

If you lose a couple of teeth on a cheap blade, it doesn't hurt as much as when you lose them on a more expensive blade. You could be lucky and not lose any teeth.

Re: Bowling Alley Wood

#7

Re: Bowling Alley Wood - Hardened nails

Stuart Johnson

I seem to remember the problem is not just that there are a lot of nails but that they are hardened. Will a regular, cheap or expensive, blade cut them?

Re: Bowling Alley Wood

#8

Re: Bowling Alley Wood - Hardened nails

Scott in Montana

I would certainly get a metal scanning wand and see what I was in for.

I offered to help a friend cut a section of bowling alley to fit in his breakfast nook. Not only were the nails hardened... they were plentiful. As I remember there was a nail every six inches or so.

All things considered, it would have been easier and cheaper glue up a new section. We went through at least a half dozen cheap blades.

Hope your project goes smoother.

Scott in Montana

Re: Bowling Alley Wood

#9

Re: Bowling Alley Wood

Howard Acheson

>>>> Any idea what blades I would use on my circular saw?

There are circular saw blade made for cutting flooring that that contains nails.

Re: Bowling Alley Wood

#11

Re: Here's one

Dick Coers

There's a lot of difference between nails and hardened nails. If they are the hardened nails mentioned earlier, I doubt if anything with teeth is going to cut them. I built my garage with pole barn, ring shank hardened nails since I was using recycled doug fir. Common nails would bend so easily nailing, but if the pole barn nails went badly, they had to be broken off. Incredibly hard! Another thought, I can't imagine nailing hard maple. That would be like nailing concrete, and I suspect the nails are like concrete nails. Good luck!

Re: Bowling Alley Wood

#12

Re: Bowling Alley Wood

kskutski

Good advice. Will do it! Thanks.

Re: Bowling Alley Wood

#13

Re: Bowling Alley Wood - Hardened nails

kskutski

Ugh! Thanks for the warning. Useful info.

Re: Bowling Alley Wood

#14

Re: Here's one

kskutski

Thanks, Howard. Sounds like I'm in for quite a bit of work. And the darn thing is HEAVY!!!

Re: Bowling Alley Wood

#15

Re: Here's one

kskutski

Thanks! Sounds like I am going to need it on this project.

Re: Bowling Alley Wood

#16

Re: Here's one

Bill White

I used alley for my bench. Nailed with spiral shank hardened nails. Was a bear to cut, but the result was worth the effort. I added angle iron braces to the bottom for stability.

You'll be happy with the bench.

Bill