Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

Whats Delta up to ?

Posts

Whats Delta up to ?

#1

Whats Delta up to ?

Charlie Lenz

I was just looking through the Rockler website and noticed that they no longer are advertiseing the Delta 50-760 Dust Collector. I know that Delta has switched owners AGAIN and is doing some cleaning up and comeing up with new products. They show six 1 1/2 hp Dust collectors, one being a new portable cyclone. Six seems like alot and has me wondering if they are going to phase the 50-760 out, which I think is a very poor decision. It was rated very highly by Fine Wood Working, and I'm thinking is a pretty good seller.

Re: Whats Delta up to ?

#2

Re: Whats Delta up to ?

Larry in NW Ohio

Charlie I`ve seen that a few times when Companies are bought out, they always seem to stop production of some of the better products and then they wonder why they don`t make any money. The only thing you can do is write them. Larry

Re: Whats Delta up to ?

#3

Kneale Brownson

Re: Whats Delta up to ?

Kneale Brownson

They're going for the mass market rather than the discerning market. Why else would they produce the Blade Runner?

Re: Whats Delta up to ?

#4

Re: Whats Delta up to ? ( Larry )

Charlie Lenz

Yeah, it looks that way. In a couple weeks Delta is offering a 1 1/2 hp portable cyclone DC, model number 50-905, some retailers are takeing orders for them at a price of $1300 - $1400. People have been adding Separators to the $400 Delta 50-760 for quite awhile allready. I built a separator with a Thien baffle in it and added it to the 50-760 that I own, and I'd be very suprised if the cyclone version works any better, certainly not anywhere close to $1000 better.

Re: Whats Delta up to ?

#5

Re: Whats Delta up to ? ( Kneale )

Charlie Lenz

Kneale, from what I'm seeing in the Facebook page, where they are showing some of the new stuff, it looks to me like they think that the average consumer has alot of money in this very poor economy. Also, if you go to Delta's website you will notice that the only table saw shown is the $3000 + Unisaw.

Re: Whats Delta up to ?

#6

Re: Whats Delta up to ? ( Kneale )

Charlie Lenz

Kneale, I think that the Blade Runner is made by Rockwell. As far as I know they aren't connected to Delta like they were in the old days, if it's even the same Rockwell.

Re: Whats Delta up to ?

#7

Re: Whats Delta up to ?

Thomas S Stockton

Charlie

No idea what they are up to but I know it is very difficult to some parts for their machines both through the place they direct you to on the web site and other sources. The part I needed is for their drum sander and nobody has it even though it is still used on the current version. I was able to come up with a fix but it makes you wonder.

Tom

Re: Whats Delta up to ?

#8

Re: Whats Delta up to ? ( Thomas )

Charlie Lenz

Thomas, I know what the problem with parts is, not too long ago they requested the parts back from our local retailers parts department, and I'm guessing that they did the same to all the retailers that had a parts department. Makes you wonder if they are scavenging for parts to put machines together, or they want a monopoly on the parts. Also our local retailer has very little in Delta products on display on their showroom floor, but they have a new Unisaw sitting in their warehouse that they won't uncrate. I also get the impression from the retailer that they aren't real happy with Delta, or too sure of their future.

Re: Whats Delta up to ?

#9

Re: Whats Delta up to ? *LINK*

Alan in Little Washington (NC)

You can't go by what a retailer sells to determine what a manufacturer produces. Rockler and Woodcraft change their offerings all the time. The new Delta company just took over in 2011 and still coming up to speed.

If you go to Delta Power Equipment Corporation (new name) website, they still list the 50-760.

Delta is still in the process of moving and adding to their in-house manufacturing line- at least four items are now made in the new Anderson South Carolina plant (Unisaw, radial arm saw, line boring machine, Beisemeyer fence and accessories). They have been sending people to the old Jackson, TN Delta factory to learn how to build and assemble various products. They have less than 50 employees at present, but there is room to expand the new factory, so who knows what else will eventually be manufactured here in the US. The remainder will likely continue to be produced overseas like was and is done by Delta and most woodworking machinery manufacturers. As the new company grows it may revise its product line, too. If you do a Google search you can find a great factory tour video (and still shots) done by Woodcraft. Below is a link to the article with stills. The link to the video is at the end.

Even though they are a wholly-owned subsidiary of Chang Type Industrial Co. Ltd., a Taiwan-based manufacturing company they have an American President/CEO, Director of Product Development, Marketing Manager, and EVP/COO all with woodworking and industry experience. Since they are trying to bring manufacturing and production back to the US, I suggest we give them a chance to succeed.

As to parts, I believe Service Net still has the contract. That may change, but some parts may not be available until the new company comes up to speed and either makes them or finds suppliers.


Delta Factory Tour

Re: Whats Delta up to ?

#10

Re: Whats Delta up to ? ( Alan )

Charlie Lenz

I'm fully aware of what you just said, plus Mark Strahler is back from Steel City and is the new director of Delta's product development. What I posted is what I was told by the retailer, which has several stores nationwide. As far as my speculation on the 50-760, as I said before, Delta has six 1 1/2 hp DC's, seems like alot of one size, and Rockler droped one, so it's easy to speculate that it might be one geting cut. Why else would Rockler drop a top seller ? Time will tell.

Re: Whats Delta up to ?

#11

Re: Whats Delta up to ?

Jason Waters

I'm worried too. Delta was one of those companies that you could always count on for spare parts, for something made a long time ago.

It wasn't disposible if you know what I mean. Like the vacuum cleaner you throw away because a new switch is more than 1/2 the cost of a new one. Yes, I hotwired mine when we were first married as we didn't have the $35 that Sears wanted for the switch. A little tricky vacuuming but we made it through it. I found a broken vac for like $5 a few months later that had a good switch!!!!!

I hope Delta gets their act together and comes out with some good stuff. They need to survive.

Re: Whats Delta up to ?

#12

Re: Whats Delta up to ? ( Jason )

Charlie Lenz

I agree Jason, I'd like to see them survive also, but the parts fiasco isn't something that sits well with customers when they need the part. And another thing is, they can't continue to sell machines that are made overseas and charge premium prices for them and the parts just because they Delta on them. Grizzly will eat them alive, if they aren't allready.

Re: Whats Delta up to ?

#13

Re: Whats Delta up to ? ( Alan )

Charlie Lenz

Alan, the link isn't working for me. Maybe others can say if it works for them or not. Anyway, we had this discussion before about how I could of saved Delta some money. For instance, their new 50-905 1 1/2 hp portable cyclone dust collector that is expected to sell for $1300 - $1400.


img

Re: Whats Delta up to ?

#14

Re: Whats Delta up to ? ( Alan )

Charlie Lenz

Now heres what I did with a 50-760 portable dust collector. After useing it several times I'd be very suprised if the 50-905 would perform any better. Delta could sell that for $800 as it sits, or add the pleated cartridge filter and sell it for $1000. The unit would be more affordable, and they wouldn't of had to spend all that time and money reengineering and retooling. Plus they could of offered the machine with or without the Separator, and sold the Separators seperatly as an accessory to existing users of the 50-760.


img

Re: Whats Delta up to ?

#15

Similar Experience

David Yoho

Recently I had to change the original planer knives on my discontinued model 22-580 planer. I installed the spare set I purchased along with the machine back when I bought it from Lowe's at close-out. A couple of weeks ago while I was in Woodcraft I asked if they still carried the blades, since I haven't seen them there in quite a while. They said they were still an active item in their system but would have to order them. I figured I could do that myself from home and left.

After looking on Delta and Woodcraft's websites I could not find them listed. All I could see were the knives for their new model 13" planer. A Google search turned up a supplier on ebay, which I ordered from. I now have two spare sets of blades that should hold me for a good while but I hope if I need other parts in the future they won't be so hard to come by. I have several Delta tools and would hate to think I won't be able to get parts or service should I need it.

Re: Whats Delta up to ?

#16

Re: Whats Delta up to ? ( Alan )

Alan in Little Washington (NC)

Like you say, it is easy to speculate, but to what end?

Personally they have too many, marginally performing DC's. I realize they are trying to satisfy a wide range of pocketbooks, but it is time to read the writing on the wall. The old style single stage DC is a thing of the past. If it is not fitted with a cyclone or some other type of separator, it won't be able to compete with today's DCs made by ClearVue, Oneida, Grizzly, etc. unless they make something they can sell for cheap.

Re: Whats Delta up to ?

#18

Re: Whats Delta up to ? ( Alan )

Charlie Lenz

Yeah, the Delta 50-905 is very similar in design to what JDS has been selling for several years, the 2100-CKV 2HP Cyclone.

Re: Whats Delta up to ?

#19

Re: Fixed it is, thankyou Alan.

Charlie Lenz

I'll have too look through it when I have a little more time. It seems to me like I've seen it before though.

Re: Whats Delta up to ?

#20

Re: Whats Delta up to ? ( Alan )

Alan in Little Washington (NC)

I won't go into why the 905 "should" perform better than what you did, but by its looks, it definately should. There are a number of principles in play that the 905 takes advantage of that a "trashcan" lid separator doesn't. I'm not saying the 905 is the ultimate and that it couldn't be improved upon (I even have some suggestions), but it should be much better than a straight drum separator in separating dust, limiting blow through, and not creating too much SP. It worries me that they think a beater bar is necessary, however. It could help clearing the filter if the user allowed the drum to overfill, but if it is needed during normal operation, I would question the cyclone design.

Since your mod requires about the same amount of steel and metal fabrication, I can't see that they could sell yours any cheaper. But, the real question is why would they? From personal experience with product development, it is incredible how costs accumulate- even the smallest nuts and bolts rapidly add up and can result in higher costs.

As to the retro-fit suggestion- that issue has been beaten to death in a few forum discussions about the Vortex Cone baffle Jet added to their newer single stage DC's.

Re: Whats Delta up to ?

#21

Re: Similar Experience ( David )

Charlie Lenz

Luckily Freud also makes Planer knives, I have a new set for the used DC-33 thickness Planer that I just bought. As far as other parts go, yeah, thats worrysome. As you probably allready know, Delta discontinued the Unifence a couple years ago, I don't agree with that decision because I like the Unifence that I have. A couple years ago I over adjusted the fence and broke the locking lug and had to buy a new one. I sometimes wonder if it happens again, will I still be able to get it in the future.

Re: Whats Delta up to ?

#22

Re: Similar Experience ( David )

Alan in Little Washington (NC)

If I were Delta (new incarnation/start-up with a tough row to hoe) and Steel City (struggling. relatively new start-up also, populated with a number of former Delta folks), I would merge, then put the their best minds to work making a really new and inventive Delta. One possible negative- some of the old Delta folks may be the same ones who allowed the the old company to stagnate. I also wonder how much capital the new Tiawanese owners will be willing to pump into Delta.

Re: Whats Delta up to ?

#23

Re: Whats Delta up to ? ( Alan )

Charlie Lenz

I guess that I didn't mention that in the drum is a Thien baffle, if you haven't tried one, then I don't expect you to know how well it works. But I can tell you from my experience with it that it works very well, it fills the drum right up to the bottom of the baffle. The beater bar on the Delta is to clear the fine dust off of the filter. Even cyclones don't separate all the dust. The cost difference between the two DC's I think that your wrong there. The 50-760 generally sells in the $400 range, how is it that you figure that a steel drum would even cost 1/2 of a $1000 ? At times I like to defend Delta when they are right, but the way that you defend Delta weather it's right or wrong is what I would expect from someone that works for Delta.

Re: Whats Delta up to ?

#24

Re: Similar Experience ( Alan )

Charlie Lenz

Yeah, I don't know what happened to Steel City, I don't hear much of them anymore. But I do remember them haveing a very popular 17" drill press, with the split head casting and long quill travel. Their Hybrid table saws were probably the best in the Hybrid category with the cabinet mounted trunions.

Re: Whats Delta up to ?

#25

Re: Whats Delta up to ? ( Alan )

Charlie Lenz

It may be about the same amount of metal, but I don't see how you can figure that it would be about the same amount of fabrication, there are far more parts on the 50-905. The bottom line Alan is that myself, a little guy that can't afford to buy materials in large quantiies can design and build quality accessories that add improved performance at a reasonable cost, why can't Delta ? The same goes for the locking lug on a Unifence that Delta wants $45 for, it's rediculous. I can have a single one made locally for a lot cheaper, infact I could probably make one myself because it's such a simple part.