Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

100+ Wood Species + Full-Shop Services: Lumber, Veneer, Tools & CNC. Everything in One Place.

Working when injured (not shop accidents)?

Posts

Working when injured (not shop accidents)?

#1

Working when injured (not shop accidents)?

Stephen Kirk

I'm curious how we make good use of our shop time when we have to deal with injuries or other health issues. It certainly isn't fun or convenient to be part way into a project and have a health problem get in the way. Sometimes, we have to find ways to still finish. Anyone have good tips?

I've dealt with rotator cuff issues in my right shoulder for 2 years now. I know my therapy, so if it returns I take care of the shoulder and try not to make it worse. Last Saturday, I did a lot of jointing and planing of large oak boards for a set of 3 bookcases. I was careful not to push anything too much, since the shoulder has been bothering me. Unfortunately, I still woke up early on Sunday with the agony of a frozen shoulder. So, no shop work for a week while I worked it I out. Heck, I was left handing a coffee mug till Wed. Since I had just been planing and jointing, I was so worried pieces would warp and twist on me. I expected to start cutting joinery during the week, which didn't happen. Fortunately, the pieces survived with little to know movement.

This weekend, I got done a little bit at a time, being sure to rest the shoulder. I think the worse part is seeing an open weekend day and knowing you can't work for the whole day. I had some glue ups to do, so I could clamp them up and wait. Plus some part sizing wasn't too much stress. The big stuff may have to wait a little longer.

Anyone else routinely deal with working through problems? Have any good tips for staying active without overdoing it and still finishing projects?

Re: Working when injured (not shop accidents)?

#2

Re: Working when injured (not shop accidents)?

Jesse Cloud

Thanks for starting this thread. I hope it attracts lots of good advice. Won't bore you with the list of things that ache, refuse to move, etc but suffice it to say that I almost never finish a project without having to give something a rest.

One thing I do is to keep a list of small shop chores on a whiteboard in the shop. There's always something that needs cleaning, organizing, sharpening, etc. I can usually handle that type of thing.

Its also a good time to go through your supplies and stock up on anything thats getting low (e.g. sandpaper, solvents, screws). Take saw blades to the sharpener. Sort through glues, finishes, etc and toss anything suspicious.

I never seem to run out of those kinds of tasks and as long as the project is interrupted anyhow, its a good time.

Also a good time to visit all the woodworking forums!

Re: Working when injured (not shop accidents)?

#3

Re: Working when injured (not shop accidents)?

George Colonel's Workshop-Havertown PA

Good Morning Stephen,

I get infirmities often which require modification of my activities. Occasionally I am unable to walk or stand because of gout, and that brings activities in the shop to a screaching halt. Otherwise, if I can work through the pain I slow the work down and work for a shorter time, or shift to other tasks integral to project completion. I can get help lifting, and wait until that help is available. Lastly, I can shift projects to lathe and scroll work. If I can get into the shop, I can always do SOMETHING.

George

Re: Working when injured (not shop accidents)?

#4

Re: Working when injured (not shop accidents)?

John McGaw

I've done some questionable things in the shop when injured and, so far at least, I'm not much the worse for wear.

During my own right rotator cuff problems which involved complete separation of the supraspinatus requiring hardware reattachment to the bone I continued to work on installing my dust collector ducting which was a bit of a drag since I kept feeling the joint separating when I picked up anything without proper forethought. Not a great feeling but I never did get the hang of thinking before moving. The shoulder came out fine and I have full mobility now.

Both times I had hand surgery I kept working at my turning and was doing heavy hollow vessels even though I had to remove the cast and bandages from my right hand at one point to make the moves I needed to. Both hands work normally.

After having emergency abdominal surgery I found myself back in the shop doing this and that despite the problem that moving around so much kept pulling the clips and stitches. Other than a rather colorful scar at the juncture of liver and ribcage everything there worked out. too

I'm too dumb to learn...

Re: Working when injured (not shop accidents)?

#5

Re: Working when injured (not shop accidents)?

TomD

If the pushing of planing is hurrting you, try a japanese plane. Works at least as well as western planes, and one can simply use some western planes on the pull. Also wooden planes are often dramatically lighter, and have far less stick. While there are reasons for prefering metal planes, reducing physical effects of planing is not one of them. Sharper blades, cambered blade, and changing planing across the board can also help

Re: Working when injured (not shop accidents)?

#6

Re: Working when injured (not shop accidents)?

Robby Wright in San Marcos, CA

Good thread. My back has been the latest piece of my body to give me trouble. I just finished up a stand-up desk for my boss and tossing the sheet goods on the tablesaw wasn't a lot of fun. I am glad I finished an outfeed table recently - it really helped me control things once I got the sheet on the saw. I am going to have to come up with an easier way to get sheet goods from the rack to the saw. Maybe a vacuum picker-upper (I think that is a technical term....) and an overhead dolly hoist might be in my future.

I will be having my left thumb joint rebuilt soon and I am not looking forward to six weeks in a cast and a couple of months of rehab. Look up "Anchovy Surgery" for details of how they do it. I read the wikipedia description of it and kind of wish I hadn't. At least it should relieve some of the pain in my hand and give me better control control over that hand.

Do we sound like a bunch of old foogeys or what?!

Re: Working when injured (not shop accidents)?

#7

Re: Working when injured (not shop accidents)?

wooden leg

There are days that I can't stand due to pressure points on my stump. On those days, I either work on plans or due small things in the shop that I can due sitting in my wheelchair. But I go to the local parts house and bs with the boys more then the other two. By bs ing I get more simple jobs and have a good time. Dave

Re: Working when injured (not shop accidents)?

#8

Re: Working when injured (not shop accidents)?

Stephen Kirk

Boy, we do sound like a bunch of old fellas. Question, how are we actually? I'm having these problems at 40, and I was hoping for some more time. Paying for the sins of my younger self I guess.

Re: Working when injured (not shop accidents)?

#9

Re: Working when injured (not shop accidents)?

Stephen Kirk

Haha, I'm working with 8" Griz jointer and a 12" Delta planer. Pushing down and extending my arm is rough on the shoulder. The planing is just a lot of reaching.

I have a lot of parts on the bookshelves, lots of repetitive work did me in.

Doubt I could use the hand planes right now.

Re: Working when injured (not shop accidents)?

#10

Re: Working when injured (not shop accidents)?

Carol Reed, Pahrump, NV

I find myself making things that handle materials more convenient, such as panel handling. I've used the electric hoist and now am finishing a titling shuttle to both transport a sheet and rotate it horizontally so it can be sawn. I used a guide and circle saw rather than the TS to break down sheet stock. I find myself replacing tools that just don't work for me anymore, due their features or lack thereof. I just acquied a big router lift for my big router because I can't hang on to it anymore. I make all my surfaces the same height, so I don't even have to lean over, let alone bend over. I flood the shop with light so I don't have bend and twist just to see. I have gathered the most used tools into a rolling buddy cart that is placed right next to where I am working, so I don't have to run back and forth. I continue to reorganize the location of tools, materials, and supplies to condense and make things more available. I added lower drawers in place of shelves for easier access. I have acquired a set of those 'reachers' that handicapped people use. I bought a roll around mechanics stool from HF so I can scoot from a lower level and not get up and down so often.

I also ration my time out there. When I hurt and/or am tired, it is time to give it a rest and go do something else. I am downright dangerous if I keep pushing it and soon I suffer yet another infirmity. Let's be careful out there, boys and girls.

I can also envision that my projects will have to get smaller. Handling sheets is hard. The pieces are easier to handle, but the assembled pieces make it hard again! I find dealing with the assembled project for the finishing to be even more debilitating. I think I will work on farming out the finishing. There are people who like finishing I am told. :)

There is no reason smaller projects can't be just as fun as large ones. If you have a larger project to finish, now is a good time to draft some help, and maybe an opportunity to light someone else's passion for woodworking and you get to pass along your knowledge.

Injuries improperly cared for is just plain dumb, as the fellow below who engaged in same described himself. Not just dumb, but also dangerous. Danger can be made less so. Continued dumb activity is stupid and stupid cannot be fixed. My 2 cents, no adjustment for inflation. Can't afford it. :D

Re: Working when injured (not shop accidents)?

#11

Re: Working when injured (not shop accidents)?

Robby Wright in San Marcos, CA

I have a bit on you yet - I turn 60 this summer - but I know there are many on this list that are older than I am.

Think I'll go sit in my rocking chair for while.... :b

Re: Working when injured (not shop accidents)?

#12

Re: Working when injured (not shop accidents)?

Joanne in Point Pleasant, PA

Yikes! Glad my thumb joints are not that bad yet. But I was having a lot of pain in them and sometimes in pinky joints. I happened to be visiting with a cousin last Spring who had been having arthritic pain in her knee. A nutritionist told her there is some research out there that shows some success easing arthritis with a gluten free diet. She tried it and within a few weeks was feeling great. And lost weight. I decided to try it. Wow! The pain in my hands is almost completely gone. If I use them a lot or play the guitar too long, I notice them, but nothing like how they were. And a nice bonus--the weather related headaches I used to get have pretty much disappeared too. Amazing! Some days I have something with gluten in it. Sometimes it doesn't bother me at all and sometimes I notice a few aches creeping in. The other thing I've been doing is taking a borage oil capsule in the morning with my vitamins and fish oil capsule. I read on some sites that borage oil helps relieve some of the arthritis ache. I think the combo of diet and oil work great! There is a lot of info online about gluten free diet and every day in the grocery store, new products available. But mostly I find I just eat healthier and cut out most carbs completely.

Re: Working when injured (not shop accidents)?

#13

Jim Rahbe, Bedford Texas

Maybe you should just....

Jim Rahbe, Bedford Texas

Stephen,

I recommend you just get your shoulder fixed.. At 40 years old you can have another 40 years of suffering or a week or two of recovery. I had my rotator cuff repaired on a Thursday and was back to work on Monday. It took about another week to get the sling off and two months of “taking it easy”. All and all it worked great for me.

Jim R.

Re: Working when injured (not shop accidents)?

#14

Could be...

John in NM

Less age and mileage than maintenance...

Obviously, I know nothing about your therapy routine, but it does sound like you could benefit from a couple aspirin and 20 minutes of icing right after activities that have aggravated the injury in the past. YMMV, I only suggest it because it is the sort of thing that has helped me in the past :)

Re: Working when injured (not shop accidents)?

#15

Re: Working when injured (not shop accidents)?

Gary Bindel

I just turned 60 two weeks ago. I usually ignore the pain as I find moving helps reduce it and at least keeps my mind off of it. Two weeks after open heart surgery I was back in the shop putzing around.

A group of friends and I get together to play cards once a month. We go out to eat before. The restuarant was busy so we decided to eat at the bar. while waiting for our food, my friend who is 5 years younger, was telling me about his latest dr. visit. He suddenly stopped and then said, "OK, I'm officailly old, I'm sitting at a bar talking about my health."

Re: Working when injured (not shop accidents)?

#16

Re: Working when injured (not shop accidents)?

Yonak

I think your advice is spot on, Carol. I've always been a loner in the shop and enjoy figuring out inventive ways to leverage moving and handling large and heavy things. I've avoided joint injuries so far.

On the other hand, regarding your suggestion about getting help, my wife is always reminding me that I could get a local high school kid to help with the labor-heavy chores. Some of them would like something to do after school, some of them the learning experience, and most all of them the extra cash. I have yet to do this but I keep it in the back of my mind.

Re: Working when injured (not shop accidents)?

#17

Re: Working when injured (not shop accidents)?

Stephen Kirk

Cleaning is a good idea. I emptied the DC, but since I hadn't done it in a while, it was a larger chore than I expected.

Re: Working when injured (not shop accidents)?

#18

Re: Working when injured (not shop accidents)?

Stephen Kirk

I wouldn't mind farming out finishing.

I agree on changing work strategies. I'm supposed to still be young and strong, but even my 40 year old bones feel the aches before too long on repetitive tasks or those requiring heavy work. I've learned to like the hold down on my Incra Miter sled - when working with many larger pieces I don't need to bear down on them to hold them steady during a cut. Takes a few mins longer, but not a big deal.

As the years go by, I'm sure I'll be looking for ways to make heavy tasks easier. If I build a new shop, or can retro fit one, I want to add a sliding hoist.

Re: Working when injured (not shop accidents)?

#19

Re: Maybe you should just....

Stephen Kirk

The thought has crossed my mind, especially as the success rate is pretty high.

Re: Working when injured (not shop accidents)?

#20

Re: Working when injured (not shop accidents)?

Stephen Kirk

But my lathe is stuck behind the stack of lumber for the bookcases!

Good stuff, even a slow down and you still produce impressive pieces.

Re: Working when injured (not shop accidents)?

#21

Re: Working when injured (not shop accidents)?

Stephen Kirk

Then I guess I'm old too. Beer dulls the pains, though.