Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Rockwell 9" Contractor's Table Saw find

Posts

Rockwell 9" Contractor's Table Saw find

#1

Rockwell 9" Contractor's Table Saw find

Charlie Lenz

I bought this saw last year, and from what I can tell it was mounted ontop of a Delta / Rockwell enclosed base backwards that was made for a 14" Bandsaw or a 6" Jointer. In my opinion it's a great little saw for the person with a small shop, the saws physical size is 25% less then the 10" saw. For what these saws are selling for used, they are hard to beat, certainly alot more reasonable then the imported plastic and aluminum jobsite saws nowdays that sell for up to $700. This is the third one that I've redone. Here is a link to the saw after I got done with it. http://vintagemachinery.org/photoindex/detail.aspx?id=13139


img

Re: Rockwell 9" Contractor's Table Saw find

#2

Re: Rockwell 9" Contractor's Table Saw find

Keith Newton

Charlie, Those are fine little saws. I have one which I bought back in the early seventies, and still use in the shop, or out on job sites. I put a Leeson 2 hp motor on it shortly after I bought it, which made it even better for those days out on the job, when I had lots of heavy ripping.

Mine has the solid cast wings, and the base uses the same legs that you put on it, but there is a little forged corner bolted to the top of each, leaving the bottom of the base open. This gives it a little smaller footprint on the floor, but I have it bolted to a couple of 2x4's, which raises it up, and stabilizes it a bit.

Do you know if you can tell the age by the serial # ?

I also have a unisaw, and PM 72 as well, but I have done a lot of hard and fine work with that little saw over the last 35 or more years.

Re: Rockwell 9" Contractor's Table Saw find

#3

Re: Rockwell 9" Contractor's Table Saw find

larry in nw ohio

Charlie That is quite a nice collection you have, I assume you try to sell these nice little toys when you have them fixed up. They really had some very well built machines back then. A lot of good companies fell by the wayside over the years, that is to bad. I wish I had time to rebuild some of them. At the old plant I worked at for a life time, we had quite a few of the old Delta/Rockwell saws. I hated those, only because they were not keeped up. The top did the raiseing up and down and the tilting and you pretty much had to use a hammer to help it move. If it wasn`t for that it would have been a good saw. Larry

Re: Rockwell 9" Contractor's Table Saw find

#4

Re: Rockwell 9" Contractor's ( Keith )

Charlie Lenz

Keith, A couple years ago I found another saw just like this one, the top of the base was smaller, it had the cast iron wings, and it had a Unifence. I put some work into the saw and ended up selling it at a pretty fair price, but to this day I wish I still had it. The base on this saw is from a Rockwell 10", I was going to fabricate a smaller top from 16 gauge metal, but the way that the fasteners are recessed into the legs I decided that it would be too much work. Who knows, maybe I'll run into another one someday that I can swap the stand and wings out. I found a Unifence at a real reasonable price, but funds are low now until I can find decent work. As far as dateing the saw by it's serial number, the historian at Vintage machines I'll bet could pin point yours for you. He has dated some of my stuff without me haveing to ask. http://vintagemachinery.org/home.aspx

Re: Rockwell 9" Contractor's Table Saw find

#5

Re: Rockwell 9" Contractor's ( Larry )

Charlie Lenz

Larry, this one I plan to keep, I may not run into another one for awhile, and who knows what condition the next one will be in. I never really understood why a person would want a saw where the top tilts. I've seen a few old ones here and there on the net.

Re: Rockwell 9" Contractor's Table Saw find

#6

Re: Rockwell 9" Contractor's ( Keith )

Charlie Lenz

Here is one I found a couple years ago and reworked. http://vintagemachinery.org/photoindex/detail.aspx?id=8464

Re: Rockwell 9" Contractor's Table Saw find

#7

Re: Rockwell 9" Contractor's ( Keith )

Keith Newton

Man, That looks nice with the unifence, and casters, but ever since I have had it, I just step between the bars, roll it toward my waist, pick it up, legs forward, and take off walking with it. Back in the early years, I took it onto the job site, and home daily. I'm sure over the years, it would amount to miles. If I didn't do enough heavy lifting, I would probably need to join a exercise club. ha

Re: Rockwell 9" Contractor's Table Saw find

#8

Re: Rockwell 9" Contractor's ( Keith )

larry in nw ohio

You really do a good job on rebuilding, Charlie. Larry

Re: Rockwell 9" Contractor's Table Saw find

#9

Re: Rockwell 9" Contractor's Table Saw find

Jason Waters

Charlie,

Nice Job!

My dad has the 9" saw my grandfather purchased for the contracting business in the mid 60's. It built many cabinets in many homes, was transported and beat up well into the 1980's. Then someone loaded it on the trailer, and the rip fence didn't make it to the desination. Since a new fence was like $350, we didn't buy one. When I got into wooworking around 1995, Dad gave me the saw. I tuned it up, replaced the wiring (which was romex by then), and bought a Delta Precision saw guide for it. I didn't do such a good job mounting it the first time, but later made a modification that allowed it to mount properly. I hated drilling the holes in the front of the tabletop and wish I had done it a little different.

Ours has the open base with the cruved out feet, and the 1 hp motor. The Delta service center here (when it was Delta/PC only) told me the 1 hp motor was a good bit rarer than the 3/4 hp, and to make sure I kept it because they were good motors.

I gave it back to dad when I got my Unisaw in 2001, and he has used it since and really likes the rip fence and that it is working good again. It's great saw, and for moving around, it's a good bit lighter than the 10" saw.

Jason

Re: Rockwell 9" Contractor's Table Saw find

#10

Re: Rockwell 9" Contractor's ( Jason )

Charlie Lenz

Thanks Jason. Speaking of rip fences, this afternoon I bought a used Unifence and rail for $100 that I stumbled upon online a couple days ago. I spent the rest of the afternoon cleaning up the rail, some wood glue spots here and there, and some burrs on the rail from nicking it, and some burrs on the inside of the rail where the locking lug locks into the rail. I had another used Unifence a few years ago that had the same problem, I don't know how people are doing it, maybe by not makeing sure that the locking lug is seated fully before locking it down is my best guess. I've never messed up the inside of the rail on a Unifence that I bought new in 1995. But I will say that you can break the locking lug by adjusting the lock down too tight, I've done that before, and the lug is expensive for what it is, about $45 plus shipping. Anyway they work alot better and smoother without the burrs. A little light fileing here and there and it's good as new. It will go on the 9" saw soon.

Re: Rockwell 9" Contractor's Table Saw find

#11

Re: Rockwell 9" Contractor's ( Jason )

Jason Waters

Charlie,

That will be a sweet little saw with with a Unifence!

I love my Bisemeyer on my Unisaw, but once in a while, I wish I could have both, as I like some of the features of the the Precision saw guide (which was like a 2/3 scale Unifence, sort of).

These new fence systems are just the thing to bring these quality old saws back to like.

Also, I found that Freud still makes some nice 9" blades for the saw. Too many people use 8 1/4" framing blades in them which are generally made cheaper and not as high quality. My dealer (and it was years ago) sold me the last 9" for a really good price, and said he would not order anymore, unless it was a special order. I haven't looked for one in years. I kept that Freud Blade as it was dull (I gave my dad a few others). I should send it to Forrest then next time I send blades out as I had forgotten about it until you brought this up.

I want to see a pic with the Unifence.

Jason

Re: Rockwell 9" Contractor's Table Saw find

#12

Re: Rockwell 9" Contractor's ( Jason )

Charlie Lenz

Thanks for the tip on the Freud blades. I looked at some of them on Amazon this morning and they are fairly reasonably priced. The Unifence I was going to think about for a bit before installing because this saw has the webbed aluminum wings, but I did get the table board hardware also minus the legs for the right side. Then I was talking to my father yesterday who lives out of state, and he has a Unisaw that he bought new about 15 years ago that has the old style Jetlock fence. So now installing the fence on the 9" saw is on hold, he may come up sometime this year I hope and get the fence and put it on his saw.

Re: Rockwell 9" Contractor's Table Saw find

#13

Re: Rockwell 9" Contractor's ( Jason )

Jason Waters

I would give him the Unifence too. Particularly if you still have the 9" saw's fence.

As for mounting the Unifence on the 9", I found the easiest way was to use a 1/4" think piece of steel, use the original moutning holes, shim it flat to the edge of the tabletop, and square, and mount the front rail like that. For the rear, I redrilled the rail. That was for the precision saw guide, because the table top was too thin to get everything to line up right.

Jason

Re: Rockwell 9" Contractor's Table Saw find

#14

Re: Rockwell 9" Contractor's ( Jason )

Charlie Lenz

I know what your saying about the front edge of the cast iron top, it's recessed some on the bottom. I've got the hardware for mounting the right side extension table, that should be no problem. There isn't a back rail for the Unifence, or a need for one, but with and extension table on the right, I usually bolt a piece of 1/8" thick X 1 1/2" or 2" flat iron along the back of the cast iron top and out to the right side for table support.