Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

OT: Removing Base Board

Posts

OT: Removing Base Board

#1

OT: Removing Base Board

Stuart Johnson

I'm in the process of replacing carpet with tile in our main bathroom. This is going to involve removing and reinstalling or replacing the baseboard. What is the best way to do this without bunging up the wall? I would like to put off wallpapering for awhile.

Re: OT: Removing Base Board

#2

Jason Roehl in Lafayette, IN

Re: OT: Removing Base Board

Jason Roehl in Lafayette, IN

I use a short prybar/cat's paw combo. Before I use it, I actually sharpen the wide end on my bench grinder. If the trim is painted, carefully run a utility knife along the top of the trim to cut through any caulk and/or paint.

Now, whether the trim is painted or not, there are a couple tricks for not damaging the walls. First is to get a 3-4" wide, stiff scraper. Put this on the wall just above the base with the handle up. You will pry against this. Next, work the sharpened pry bar in between the base and the wall with hand pressure only--don't hammer it. It's best to start in the middle of the piece of base at a nail, if you can find one, so that the base doesn't split. When you pry (push towards the wall), don't go for the home run--that is, don't try to pry it all the way off in that first location. Just get it a little bit loose, then move down the wall to the next nail and do the same thing--don't try to pry it all the way out. Gently "wiggling" the pry bar is more effective than pushing hard. It should take 3 or so passes over the length of the base to get it out far enough to get your hands behind it to where you can continue the wiggling with your hands. Again, don't try to pull it all the way off from one place.

Jason

Re: OT: Removing Base Board

#3

Re: OT: Removing Base Board

Dave Paine

I have a curved rather wide pry bar. 90 deg bend at one end, about 45 deg at the other.

I use a piece of scrap 1/4in ply behind the bar to spread the load and avoid dinging the wall.

I carefully apply pressure behind the baseboard at the location of a nail. Sometimes the nail comes out with the board, and so I can press the board back to the wall and then remove the nail with pliers.

Sometime the nail stays in place and I ended up having to force the board across the nail. This can result in breakout on the back and potential for wood filler.

Good luck, you will need it. Easier to avoid damage to the wall than the base board.

Re: OT: Removing Base Board

#4

Kneale Brownson

Re: OT: Removing Base Board

Kneale Brownson

Cut the paint at the top of the baseboard if there is any, slide a drywall taping knife behind the baseboard to protect the wall and use prybars. I use a small and large Stanley prybars, the small to start the prying, the large to complete.

Re: OT: Removing Base Board

#5

My suggestion

Lee Schierer McKean, PA

If you remove the baseboard and are putting tile on the floor, I would suggest putting tile wall base to replace the baseboard.

Lee

Re: OT: Removing Base Board

#6

Re: OT: Removing Base Board - Thanks

Stuart Johnson

Thank you for the answers. It sounds like it won't be too much of a problem. I'm not concerned with saving the old stuff as it'll only take 4 or 5 8' pieces if I have to replace it all.

Lee, we are going with a laminate tile not ceramic.

Re: OT: Removing Base Board

#7

one other thing

Bill Tindall

Don't drive the nails out. Pull the heads through from the back side.

I am not sure the excellent directions made clear the pry bar required. It is about 8" long and has a thin, wide, flat curved end that can be slipped behind the molding. The curve enables prying with it. This tool is essential.

Did someone mention "go slowly".

Re: OT: Removing Base Board

#8

Re: My suggestion

Larry in NW Ohio

Basically the same as everyone else said with one more suggestion. I use a stiff puddy knife and sharpen the end a little and get that behind the baseboard and use that to bring it out a little so you can get the pry bars behind it and work it off. Or you could use a thinner puddy knife to break the baseboard loose and get the stife one behind it to work it looser. Good luck. Larry

Re: OT: Removing Base Board

#9

Re: OT: Removing Base Board

Bill Houghton, Sebastopol, CA

Beekeepers sell a "hive tool," about $5. Two of those are right helpful.

I also got one of those handles that will take a hacksaw blade (with the blade flopping around, unsupported), available at your hardware or big boxy store. This will allow cutting any nails that are getting in the way of not damaging the wall.

Other suggestions have been great.

Re: OT: Removing Base Board

#11

Re: OT: Removing Base Board

Bob Entwisle in NJ

One of the most useful demo tools I know of is a good 5-way painters tool. It's excellent for slipping behind trim and coaxing it free without damaging the adjacent drywall.

Bob in NJ

Re: OT: Removing Base Board

#12

Re: OT: Removing Base Board

George Koch

Stuart, also examine the inside corners and determine if they are mitered or coped so you will know which one to remove first. George

Re: OT: Removing Base Board

#13

Re: OT: Removing Base Board

Cecil Nickerson in Halfmoon Bay

I've used a wafer thin cat's paw from Lee Valley for years and it works really well. Use a broad knife or drywall knife to avoid damaging the wall. Search the Lee Valley site for Restorer's Cat's Paws. Mine is the 8-inch.

Good luck, Cecil

Re: OT: Removing Base Board

#14

Re: OT: Removing Base Board

Rick Haverstock

Surprised that no one has mentioned this yet, but if you can see the nailheads (or the circle ftom the filler hiding them), use a nail set of the appropriate size to drive the nails below the surface of the trim as far as you can go without greatly enlarging the hole. Then use your favorite prying method as outlined by many above. This trick was taught to me by a long-time contractor and it works like a charm. The trim remains undamaged and the nails are easier to pull out without the baseboard in the way.

Rick Haverstock

Re: OT: Removing Base Board

#15

Re: OT: Removing Base Board - Done

Stuart Johnson

Thanks to the help here it took less time to remove it all than it's taken to read all of the advice. I cut the along the top to break it loose. That alone caused it to come out just a bit with the pressure from the utility knife. I slid a large putty knife behind it and gently wiggled it until I could get a small bar behind it. A bit of 1/4 inch plywood to spread the force and it was done. One little 2" piece was glued but I was able to finally pop it off with out any damage except right at the base. That will be covered by the replacement.

Re: OT: Removing Base Board

#16

Now about installing....

Frank G

The inside corners can be tricky , coped or 45ed. The dry wall finishers stop with the corner mud a couple of inches from the bottom. When you nail it tight, the bottom will kick in and leave a lot to be caulked.

If you run a drywall screw in the bottom plate and use it as an adjustable stop (checking depth with a straight edge held vertically) several inches from the corner your life will be easier. The outside corners will take care of them selves. They just seem to know better.

Re: OT: Removing Base Board

#17

Re: OT: Removing Base Board

Jim Hager

I do a lot of removal of base boards during kitchen installs. I use my Fein Multimaster with the scraper blade to cut through the caulk and then change over to a metal/wood blade to cut through the nails. If you've only got a little to do and not too concerned about the baseboard but trying only to save the wallpaper your best bet is a good utility knife and small pry bar.