Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

general purpose/resaw blade for 14" bandsaw

Posts

general purpose/resaw blade for 14" bandsaw

#1

general purpose/resaw blade for 14" bandsaw

Adrian

Even though the books seem to suggest that I should have a collection of blades and be willing to switch blades all the time, the reality is that I just use the blade that's already on the saw. The current blade is a cheap 1/2" 3 tpi blade that's been on the saw for about 7 years, so I suspect I can get better performance with a new blade. This blade size has been mostly OK. Occasionally I run into the turning radius limit, but not much. Note also that I do not have a table saw, so the bandsaw is it.

So I'm looking for a blade that I can use for cutting materials usually 1/2" - 2" thick, but with occasional resawing up to 10". I've done all these things with the current blade. It would be nice if blade lead was reduced so that the slot on the table was usable. (I read in one of the bandsaw books that carbide blades eliminate blade lead. I also read of somebody decreasing lead by adjusting the tracking on his saw. I have a significant amount of lead.)

In old posts on this forum somebody said that on Lonnie Bird's recommendation he was using the carbide tipped Lennox Trimaster 3/8" 3/4 tpi variable blade as a general purpose blade and it was fantastic. However, this blade has a thickness of 0.035" and Duginske says that running such a thick band on a 14" saw will lead to premature failure of the band---something I really don't want to encounter if I shell out for that expensive blade. Any thoughts on this? I couldn't figure out the size of the kerf for this thing. Is it huge? Can I resaw with this 3/8" blade? People talk about the trimaster blades producing a smooth finish. Can it produce a smooth finish for cutting curves?

Are there any other carbide blades that might be better suited to general purpose use on a 14" saw? The trimaster 1/2" is thinner (0.025") but doesn't come with the variable teeth. I have read that carbide blades require more tension, which seems odd---I don't want something beyond the capacity of my Grizzly G0555.

If I don't go with carbide I think I want bimetal so that I don't have to worry about rapid dulling. Any comments on a general purpose bimetal blade?

What's your favorite general purpose blade?

Re: general purpose/resaw blade for 14" bandsaw

#2

Re: general purpose/resaw blade for 14" bandsaw

Larry in NW Ohio

Adrian I`ve been getting mine from "Supercutbandsaw.com lately and I like them. They have carbide , and they are not to expensive, IIRC they are not much more than a Bi-Metal blade. Del may chime in, because he bought a couple and likes them. The only thing you need to call them for a price. Larry

Re: general purpose/resaw blade for 14" bandsaw

#3

Re: general purpose/resaw blade for 14" bandsaw

AlanWS

If you have been using a standard blade for years, chances are you don't need to go to carbide for better performance. A sharp blade should be an improvement, and the question is how long that lasts.

You can adjust the tracking on your saw so the blade rides in the middle of the tire on the top wheel, and as long as the blade is sharp, it should cut with little lead angle. The key point is that this works well with sharp blades, and that funny lead angles are frequently the result of dull blades. You can tweak the tracking to get the cutting angle as parallel to the miter slot as you can.

A 1/2" 3 TPI blade sounds like a good choice for your work. Sharpness is more important for resawing than for other cuts, so you could demote a blade when it no longer resaws well.

If you want to try a bimetal blade, the Olson All-pro bimetal blade is available in a 1/2" 3 TPI version with a 0.025" thickness. Other vendors' stock is thicker.

Re: general purpose/resaw blade for 14" bandsaw

#4

Carbon steel for me too....

John in NM

Just a 1/2" 3 or 4 tpi blade. My use if very much like yours, though lately I have kept a dedicated resaw blade on hand. Same size, just one that is designed to cut a bit smoother (mine is a Woodslicer, there are several similar options).

I also like Highland's general purpose blades, cut is really good, better than those I make myself. They run $15 or so for my saw, a little more than a Supercut (shop I used to work for used those, they are good too).

For cheap, I buy 100' rolls of blade stock from Victor Machinery in Brooklyn. Last time it came out to about $5 per blade (mine are 111"). I silver solder them with a home made jig and jewelers (hard) solder. Welds last longer than my solder joints, but then I'm not very good at it :D

To be honest, I'm really not sure your lead problem will be solved by the blade. There's no basis for the claim that I'm aware of, and wheel alignment is simply more plausible. But I've never had to fix one - I was lucky to buy a saw new that ran true from day 1. I've used wanderers in various shops, but the boss never wanted me to spend time correcting the saw.

Re: general purpose/resaw blade for 14" bandsaw

#5

Re: general purpose/resaw blade for 14" bandsaw *LINK*

del schisler

i use 2 different blades. One for resawing a 1/2" 3tpi and than a 1/4" 4tpi and that is all that i use. Now for blade drift you need to set the fence up for that. If you don't know how to do that come back and i know i or some one else will tell you how . I buy my blades from here Suppercutbandsaw cut. You call then and tell what you are going to do and they will get the blade for you . Here is the link

http://www.supercutbandsaw.com/

Now their are lot's of blades out their but i tried a few and this blade will out cut . I used to use the woodslicer for yrs now i use this blade from suppercutbandsaw it cut's better. Also i use cool blocks in the guide's Some have cut 1/2 by 1/2 oak and use those for the block's. here is a list of blade size's and tpi WIDTH TPI APPLICATIONS

1/8" 14 TIGHT SCROLL CUTS TO 2" THICK

3/16" 10 MILD SCROLL CUTS TO 3" THICK

1/4" 4 GENERAL PURPOSE 3" TO 4" THICK

3/8" 4 CONTOUR CUTS 4" TO 5" THICK

1/2" 3 RESAWING WOOD 6" + THICK

5/8" 3 RESAWING WOOD FOR 14" SAWS 6" + THICK

3/4" 3 RESAWING WOOD FOR 16" SAWS 6" + THICK


http://www.supercutbandsaw.com/

Re: general purpose/resaw blade for 14" bandsaw

#6

Re: general purpose/resaw blade for 14" bandsaw

Lewis Dodd

I use the Olson All Pro from Rockler and have been very happy with them (105" , 3tpi,hook, raker set,about $20.00) I am running a 5/8" right now and a 1/4" for small detail work. Got to admit, it took me a long time to find this blade, but am quite pleased with it. I go through about 2-3 a year.

Re: general purpose/resaw blade for 14" bandsaw

#7

Re: general purpose/resaw blade for 14" bandsaw

Adrian

I know how to adjust the fence for blade lead. What I don't know how to do is adjust the slot for the miter gauge, e.g. for making cross cuts. I guess on some saws the whole table swivels, but I don't think mine does that. (And swiveling the table would be a tough adjustment to get right.)

Re: general purpose/resaw blade for 14" bandsaw

#8

Re: miter gage

del schisler

Don't you miter gage have adjustment's on it like the miter gage on a table saw ? If i am thinking right

Re: general purpose/resaw blade for 14" bandsaw

#9

Re: miter gage

Jason Waters

If I am thinking right, yes you can adjust the miter head for square, but unless your blade is square to the miter slot, you will have a problem. It might be ok for cutting 3/8" dowels, but for 12" long pieces, this will definately be an issued, as the miter slot is diverging or converging with the back of the blade, and you'll be forcing the balde to cut at an angle, and it will be a mess.

I had to align a tablesaw that did that once, really important there if you want to use the miter gauge.

So if you can't get the lead adjusted, the miter slot becomes an issue.

Is it possible you need a bearing replacement?

Re: general purpose/resaw blade for 14" bandsaw

#10

Re: miter gage

Adrian

If the set on a bandsaw blade is not uniform on both sides then it will exhibit lead, that is, it will "prefer" to cut in a direction not parallel to the blade itself. From what I've read, blade lead is considered a normal (unavoidable?) feature of bandsaws. That's why all bandsaw fences swivel to adjust for it, and some of the books I read say the miter slot is useless. You do not have to have the blade twisted and misaligned with the miter slot to have lead. There's no reason to think the bearings have a problem. From what I understand, other parts of the saw will fail before the bearings, and in any case, I'm pretty good about taking the tension off when I'm not using it.

I called up Louis Iturra and talked to him for a while about blades and he claimed that the carbide blades are made to a higher precision than others because of how the teeth are individually milled. So he agreed with the book that claimed that these blades tend not to have lead.

Re: general purpose/resaw blade for 14" bandsaw

#11

Re: miter gage

Stuart Johnson

This is a nice setup to handle drift and give a larger work surface.


Re: general purpose/resaw blade for 14" bandsaw

#12

Re: miter gage

wilbur

There's another way of dealing with lead, or drift, as some call it.

First step is to center the blade on the crown of the upper wheel, as Alan had mentioned before.

Second step is to set your fence so that it is parallel to the miter slot.

Third step is to adjust the table so that the fence and miter slot are in line with the blade. You can check this by making a test cut with a board up against the fence, and see if the blade is centered.

The disadvantage of this method is that it involves tweaking the table position by loosening the bolts holding the table to the bandsaw and making fine adjustments.

The advantage is that you'll never have to deal with setting a fence for drift again, since any time a blade is centered on the upper wheel, it will be in line with the fence and miter slot. So you're trading about an hour's worth of tweaking your bandsaw for not having to go through the fence adjustment method every time you change a blade, which will make you more likely to change a blade when you need it rather than making do with the blade that you have.

The other advantage is that you can now use the miter slot for crosscutting, since everything will be in line or square the way it needs to be.

Going back to your original blade question, I use a 1/2" x 3 tpi blade for 95% of my cuts, and I'll use narrower blades when I need to cut a tight radius. Currently I'm trying out a bimetal 1/2" x 4 tpi blade, as the bimetal blade that I got didn't come in a 1/2" x 3 tpi size.

Re: general purpose/resaw blade for 14" bandsaw

#13

Re: miter gage

Adrian

The notion that the machine can be set up once and for all to eliminate blade drift is interesting, but many people claim that blade drift is (partly?) caused by the blade itself. I read that some blades are shorter at the teeth than at the back as a result of the hardening process on the teeth. A blade of this sort riding on the center of the crowned wheel would give lead. And some blades are said to be asymetrically set which also causes lead.

I did notice in the manual for my saw that they mention the possibility of rotating the table. It wasn't obvious that this was possible.

Re: general purpose/resaw blade for 14" bandsaw

#14

bandsaw tracking and blade lead

Adrian

For the curious, I went ahead and sprung for a 3/8" 3-4 tpi variable trimaster. Iturra was having a sale on them.

So I fit the blade on my saw. I tried to get the wheels coplanar. (Close, but not perfect. The tension really changes the wheel alignment considerably, which makes this rather difficult.) I have it tracking close to the center, though not exactly on the center. The back edge of the blade maybe is at the center? And I did a blade lead test and there's enormous lead to the left. (I have to push the workpiece to the left to cut straight.) In fact, it's so much that my fence won't adjust that far.

It seems to me that this means I need to mess around with the tracking. But one observation I had was that I tried to check if the blade was parallel to the miter slot, and to the level of accuracy I can measure, given the small size of the blade, it *is* parallel to the miter slot. (If I set a straight edge against the blade it is parallel to the fence, which I aligned to the miter slot.) I'm not quite sure what to make of this. The lead line I drew on the saw table shows a 9/16" shift across the 14" length of the table. (This would correspond to a .015" shift of the blade, which seems like a sufficient amount to detect.) Also if the lead is caused by tracking, then shouldn't it go the other way? I mean, if the back of the blade is at the crown then the blade should be twisted with the teeth to the left at the point of the cut, so lead should be to the right.