Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

fixed my Air Compressor

Posts

fixed my Air Compressor

#1

fixed my Air Compressor

Barry Irby

About ten years ago I bought a Sears Air Compressor used for $50 as a backup. I started remodeling homes and my main Air Compressor went out on the jobs. The backup came into play in my shop and has been in use for about five years. About two weeks ago it just quit. Checked it out and found out the pressure switch was the problem. Tried for a replacement locally, but no go, had to order it from Sears. Got tired of waiting and talked to a friend of mine who told me to remove the pressure switch and check the orifice in the bottom of it. Since mine is outside in a closet attached to the exterior of my shop his thought was that condensation got to it and rust the orifice closed. I was reluctant to do it because I would have to stand on my head in the closet out there in the cold and with no assurance it would work, I ordered the replacement. The Sears guy on the phone talked me into buying a belt while I was at it. They sent the belt but said the switch was on back order. They keep sending E-mails with "up-dates" reminding me it is on back order and that they are glad to be of service. So, It was pretty warm outside today and I attacked the compressor. Figured I had nothing to lose, you can't break something that is already broken, and I needed to remove the switch to put the new one on anyway. Finally got it off and cleaned the orifice with a tiny drill bit and put it back on. Good as new. Now I should cancel Sears slow service.

This is just a tiny gloat and I thought I would share in case somebody here has the same problem.

Re: fixed my Air Compressor

#2

Re: fixed my Air Compressor

larry in nw ohio

Glad to hear that you fixed it yourself, the best kind of fix. As we always said at work, "Better than new, rebuilt." It`ll probably work longer now. Larry

Re: fixed my Air Compressor

#3

Re: fixed my Air Compressor

Jim Breeden

Far as I'm concerned Sears is a pain in the glutus maximus! First time was when I had to replace a bearing on a belt sander, "You are not allowed to do that, because you have to take the armature out, and you might get shocked,

so we will charge you $65 to look at". What!? Went down to the local bearing place and paid $1.78 for two bearings. Same thing with a drill - ha, take that! :b

Re: fixed my Air Compressor

#4

Re: fixed my Air Compressor

Lewis Dodd

Next time, if necessary to replace it, go to a regular "pump-like submeresible pump water well pressure switch. You may have to adjust the ranges (on/off) but a pressure switch is a pressure switch! Sears used to make one for on and another for off, they got to sell more that way! Got one compressor that comes on at about 30 psi and off at about 70 (solely painting), another is set to come on at 90psi and off at 125 psi (shop general). Fire ants and calcium/rust used to be my favorite "friends.

Re: fixed my Air Compressor

#5

Dale Lenz

Thanks for posting, Barry.


Re: fixed my Air Compressor

#6

Re: fixed my Air Compressor

Barry Irby

I looked at buying a replacement from Grainger. They had about fifty and many of them were cheaper than the Sears one. The Sears version was from Furnas, a company that has gone out of business. Mine needed to have an "unloader" on it to bleed the pressure from the cylinder so the unit would not have to try to start against a head of pressure. Really had no way to cross reference and did not want to take the old one off and go to Granger to beg for a chance to try to match it. It had to physically fit the piping as well as have the right pressure range. It was mostly that I needed to catch a warm day with time to fix it.

Re: fixed my Air Compressor

#7

Thanx from me too, Barry.

Stuart Hough

I have a Sears unit also. This info will come in handy one day, I fear!

Re: fixed my Air Compressor

#8

Re: Thanks from me too, Barry.

Barry Irby

Stuart, I suspect most air compressors have a similar switch and that the problem might not be with the Sears unit only.

The part I have not made clear is that the switch has a "pipe" fitting hanging out the bottom. It has a hole in it that is about 5/32" or 3/16" in diameter but there is an orifice above it that is closer to 1/32". there was some rust in the larger tube, but the orifice was what was blocked. There is diaphragm above the orifice. I used a tiny drill bit in a little hand drill (can't think of the name of the little hand drill). I set the bit to a depth that could not reach the diaphragm and cleaned out the orifice. Being careful not to punch a hole in the diaphragm.

The hardest part of this was removing and reinstalling the switch assembly. Sat there with two wrenches turning the thing about a 1/16th of a turn over and over. It would have been easier to remove the motor but the nuts that the bolts thread into are between the mounting base and the tank and it would have been tough to put them back. So I sat there and fiddled. Nest time it might be worth while to buy a stubby wrench.

Re: fixed my Air Compressor

#9

If you need to make an unloader...

Dave Paine

Barry,

Glad to hear you got the compressor back in service.

I have a Campbell Hausfeld unit and the instructions talked about running the compressor for x mins to break in the unit. I did this and ended up melting a plastic orifice on the pressure switch which was the unloader. Replacement only via a dealer, and the closest is not too close.

I ended up removing the fitting at the pressure switch and on the free end of the plastic tubing I installed a brass 1/4in needle valve I happened to have lying around. I cracked this only just a fraction. The amount of air it leaks during compression is miniscule. After the compressor shuts off at the 135psi setting, the slight opening in the valve allows the pressure to dissipate in a short time. So far this time is much less than the time to re-start based on my tool usage. I now prefer this to the louder sound if I had the normal unloader.

Re: fixed my Air Compressor

#10

Kneale Brownson

Very common problem with Compressors


Re: fixed my Air Compressor

#11

Re: Thanks from me too, Barry.

Kurt

It depends on how your compressor is plumbed. I have an old oilless C-H that had a 10 cent (at least that's what it worth) pressure switch/unloader. I ordered a new one and couldn't get it to quit leaking. Returned it and got separate pressure switch and unloader from Grainger. I have a copper line running from the compressor head to the tank. The unloader is a brass fitting that fits between the tank and copper line. The fittings and threads were correct. The pressure switch had an on/off switch built in, think it's squareD . It's been fine for 10+ years occasional use. I know you can now get non-plastic combo pressure switch/unloaders. I don't recall having that option when I needed mine.

Re: fixed my Air Compressor

#12

Keep It Fixed

Mark Mandell - Gone Round In Jersey

If you're getting corrosion as described it's a sure sign that you're not draining the condensate water from your compressor's tank. Compressors that are moved around to job site should be drained and left open between uses. Stationary compressors, like the one in your closet, should have an auto-drain installed. McMaster-Carr sells an air-actuated unit, part 4919K13, for $50 that will drain the condensate water once during each compression cycle. While it is sensitive to freezing temps, I've had one on my IR 60gal. in the garage for almost 10 years without an issue. I do open and clean it once or twice a year.