Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

router lifts

Posts

router lifts

#1

router lifts

Carol Reed, Pahrump, NV

I want to put my PC 7518 in a lift without without breaking the bank. Recommendations from actual users, please.

Re: router lifts

#2

Re: router lifts

Grant Wilkinson

The Jessem lift has served me reasonably well - not stellar, for sure. However, in hindsight, I believe that it is overpriced. I would not buy it again. The phenolic table was definitely a poor, very expensive choice.

After sale service is poor, too.

Re: router lifts

#3

Shopnotes Vol 21 Issue 121

Carlos Clarke

How about the lift in the latest shopnotes?

Re: router lifts

#4

Re: router lifts

Ralph Lipeles

I built one from American Woodworker plans that were available on line. It is very solid. Construction is a carriage sliding on 3/4 steel rods and bronze bushings. Cost was about $60.

Ralph Lipeles

Re: router lifts

#5

Re: router lifts

Dick Coers

I have a Router Razer on my Dewalt, but love the look of this one.

http://woodgears.ca/router_lift/index.html

Re: router lifts

#7

Me Too

Tony - Memphis

I have the Router Raizer on a Hitachi and I have been pretty satisfied with it. I think they are around $90 now. It was easy to install and it works well.

Tony

Re: router lifts

#8

Re: router lifts

George Colonel's Workshop-Havertown PA

Good Afternoon Carol,

I use the JessEm Master Lift on my P+C 7518. It only breaks the bank for a little while! The JessEm is well made and solid, and has worked very satisfactorily over the three years which I've used it. It holds the height setting, and height adjustment is a snap with a set up block or mating profile. The table surface area and router plate remains flat despite the very heavy weight of the router. No sag.

I also bought various center inserts for different bit diameters, and an adapter which accepts my P+C 690 machines.

I had a small problem with it initially because the center insert tightens in a counter clockwise direction, which is counter intuitive. The wrench JessEm supplied was too frail to cope, and I had fits before eventually freeing the insert. Phone calls to JessEm for help were not productive, and they gave me the idiot treatment. They promised to send me a replacement insert, and never did. So, customer service really was poor. It still gets me angry after having spent all that money.

Its a good tool nevertheless. Had I the need to buy a lift today, I'd certainly not buy JessEm because of Customer Service failure in the past.

I didn't try to build my own. I would still bite the bullet and buy a commercial lift. There are several out there like Bull Dog and Wood Pecker. I'm not so sure they are necessarily better than the JessEm, but are worth looking at.

Let us know what you decide.

George

Re: router lifts

#9

Re: router lifts

Joseph Mulherin

Rockler has one on sale right now for about $150.

Re: router lifts

#10

Re: router lifts

Dave Paine

I have a Woodpeckers Universal Router Lift where the router mounts to the baseplate just gathering dust. This is no longer made. I upgraded to a different model.

For the price of shipping you can have this.

Re: router lifts

#11

Re: router lifts

Carol Reed, Pahrump, NV

Wow, Dave. Thanks. Email me your phone number at carol.j.reed@gmail.com along with a good time to call and we'll work out the details. I am going out in a few minutes so maybe we could connect tomorrow sometime?

Re: router lifts

#12

Re: router lifts

Jim Pugh

Carol, I just bought the Woodpecker lift and table, etc. I did quite a bit of research for lifts and this one kept coming to the top. Check Amazon for prices and for comparisons to some of the others available. Kreg supposedly makes one but I think it is made by Woodpecker. All of their stuff looks very similar to what is available from Woodpecker. Oh, and they are manufactured about 25 miles from me here in Ohio - not that that influenced my decision to buy them....

Re: router lifts

#13

Re: router lifts

Jason Waters

I have a Jessem lift, but mine is about 8 years old or more I guess. Mine actually has an aluminum top, and has "JET" on it as they sold them under their name for a while. I got a pretty good deal on it I remember, though it was still expensive. I have a Hitachi M12V mounted in mine (It was a lift that would accomodate this router). I have been pleased, but there are many out there today. The Rockler looks promising from my memory, and seems rightly priced.

I know many people have built theirs, but I think this is one place it's better to buy. That's after building a few router tables (3 I think) over the years. Making your own inserts can be a pain if you are starting out. Ask me how I know.

Thankfully I didn't need customer service on mine though, seems like others here have had less than stellar experiences, which would turn me away as well.

Re: router lifts

#14

FWIW....I too have a Woodpecker

Terry Alexander

Bought it probably 10 years ago....and like you Carol, I didn't want a router lift that cost more than my 3 1/4 hp Hitachi. Yep.....lift isn't sold anymore nor it the router. When either of these break it will break my heart. I've used this combination for over 10 years....HARD! No complaints or problems. Then again, I am very meticulous about keeping my tools clean, lubricated, and in top notch shape.

HTH

Terry Alexander in West Texas

Re: router lifts

#15

Me Too - Router Raizer

Brian in SLO

I also have the Router Raizer running a Hitachi M12V. It works great, holds its place without moving due to vibration. My only wish would be for an ability to do above the table bit changes. But with the Hitachi that is just not possible.

The truly great thing about the Raizer is customer service. I needed some new magnet chips and a dust cover for the raizing hole and the guy who answered to phone was very helpful, cheerful and let me know if I ever needed anything to just give them a call.

Oh, and the parts I needed, they sent them right out at no charge.

Re: router lifts

#16

Re: router lifts

Jason Waters

I looked at the Rockler, and I'm not sure it will fit the PC you have.

Looks like another person is going to send you a lift. Good Deal!

Re: router lifts

#17

Way to go girl!

Mike Farinella

Yippee!

Re: router lifts

#18

Ha!

Tony - Memphis

I can't tell you how many times I have fished the little cover out of the shop vac! They included a spare, and I'm glad it is magnetic. Makes it easier than sifting through the dust.

Tony

Re: router lifts

#19

Re: router lift update

Carol Reed, Pahrump, NV

A very generous fellow from this forum had upgraded his older Unilift and made me a deal I could not refuse. It arrived and my 7518 fits perfectly. It came with two of the three table inserts.. He has found the third one (the stepped one) and promised to send it along. Meanwhile I looked at the set of 8 additional inserts on the Woodpecker site for $40. $5 per is not bad. $15 for shipping is another matter. Not Woodpeckers fault. They are only getting a couple of bucks over USPS rates for shipping and handling. Lest you think this is outrageous, packing materials are not cheap, nor is the labor to get a package into a shipping system. USPS is less expensive than other shippers, so shipping is what it is.

However, everyone likes to save a buck. So two questions. Anyone try to make their own inserts to fit these lifts? Or anyone have a set collecting dust?

Re: router lifts

#20

Re: router lift update

Bruce, a MN Galoot

I just finished cutting a couple Baltic Birch circles for a trunnion to go on a new belt grinder. I was able to grind them (using the old belt grinder) to a very small fraction of an inch, but it is certainly fiddly work. Given your abilities, making new inserts is easily doable, but expect to put in a fair amount of time. If you have more time than money, and who doesn't, then maybe the answer is academic. Besides that, phenolic plate is expensive stuff.

Re: router lifts

#21

Re: router lift update

Charlie Lenz

I bought the 8pc ringset made of aluminum when I bought an aluminum router plate from Woodpeckers, I paid around $80-90 for the set. Now I think the ringsets are made of plastic, unless they do a special run of aluminum ones, which I have seen before. They twist and lock into the router plate, attempting to make a set out of anything I think would be a very time consumeing task, and cost prohibitive.

Re: router lifts

#22

Re: router lift update

Dave Paine

i made an insert for my drill press, since I did not like the large hole in the original. I seemed to miss holding the bits when I unscrewed the chuck and they fell through. For the small diameter about 2in this did not take long.

I think you will find that you do not need a set of inserts. I most frequently use the 2 1/8in ring. Most space for the dust collector's air. I have only a couple of bits which are larger than this ring. I just want a ring which will give adequate clearance for the bit and allow good airflow. The benefit of wood or phenolic is to minimize risk is a bit did touch the ring. Too easy to raise a large bit more than anticipated. I have experienced this with my sacrificial adjustable fence. Made the gap a little too narrow for the bit. Since it is made of MDF, no damage to the bits.

After reading this, I decided to give a try to turning a ring. It will not lock, but I am not expecting the locking action is necessary. I found a piece of scrap walnut which should have a stable grain pattern.

I will report back on whether this works out. At present the piece has been rounded and faced off. Now to turn to correct diameter and carefully cut for the 1/16in thick flange to hold in place.

A big unknown will be whether this warps over time. I do have a phenolic sheet I purchased to make a router plate if this does not work out. I never did use this since I purchased a lift which had an aluminum plate.