Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Nearly 100 Exotic Wood Species, Direct-Imported Since 1972. Shop Slabs & Turning Stock.

OT-Help needed on front-loader washing machine

Posts

OT-Help needed on front-loader washing machine

#1

OT-Help needed on front-loader washing machine

Nat Robison

I have a 4-year old Frigidaire front-loader washing machine. So far, it's been great.

My problem is the machine will not spin, at least regularly. I started a load the other day and came back and it was soaking wet. It was not a load with any crazy items or weight issues. I ran a spin only cycle and it drained the water but wouldn't spin. I took out about half the load and tried again. No luck.

I just removed the rest of the load and tried to start a wash cycle and it filled and spun for about 30 secs. and then stopped spinning.

I removed the back.....the belt is intact. I tried the spin the empty drum and it took a bit of effort but I got it to go but it feels as though something is blocking it from spinning freely.

Is it possible for something small to work its way behind the rubber bellows and cause a problem. Do I need to dismantle more of the machine? As of now, it seems like all the pumps and motors are working. Anyone have a similar problem? I'll check the rest of the internet for solutions as well.

Re: OT-Help needed on front-loader washing machine

#2

Re: OT-Help needed on front-loader washing machine

Joseph Mulherin

Nat, I just asked about the problem and here is their answer:

Remove the larger black suction hose and clear out any things which may have got into it; also check the impeller of the pump...it might have something lodged in it keeping it from spinning.

Good luck...Joe in Indio, Ca

Re: OT-Help needed on front-loader washing machine

#3

Re: OT-Help needed on front-loader washing machine

Larry in NW OHIO

Nat I have a few sites that have come up here@WC over the years and I put them into my favorites in case I would need them. You might try www.repairclinic.com, or acmehowto.com ,or naturalhandyman.com or repairshack.com GOOD LUCK, sorry I can`t think of anything that may help, except the motor sounds sluggish. Try and take the belt off and run the motor if you can. If it has a capaciter it may need a new one. Larry

Re: OT-Help needed on front-loader washing machine

#4

Re: OT-Help needed on front-loader washing machine

Yonak

Nat, my front-load washing machine had the same problem of not spinning. It turned out the door wouldn't lock because of a bad control panel, and since it wouldn't lock, it wouldn't spin. Check to see if the door will lock before you take it apart.

Re: OT-Help needed on front-loader washing machine

#5

Update

Nat Robison

I surfed some other sites and found lots of potential problems.......control panels, door switches. My eyes tend to glaze over when I read out checking for the resistance drop between the green wire and red wire, etc.

Anyway, I got the machine apart and decided to clean out the pump filter first. Mine is not a screen as much as it is a cylinder with holes smaller than a dime. I swear I cleaned about 3/4 of a cup of crap out of it. Hair bands, bobby pins, coins, lint. I'm surprised anything could pump out of it. It was relatively easy.

I put the machine back together and I'm running a test load right now and the machine appears to be OK.

Re: OT-Help needed on front-loader washing machine

#6

Re: Update

Larry in NW OHIO

Way to go Nat, Good Job. Larry

Re: OT-Help needed on front-loader washing machine

#7

Re: Update

nickb

Our newish Samsung front loader came with directions to clean the filter regularly (every few months - my wife has a reminder in her Outlook calendar). Pulled out a few odd things (bobby pins, a toothpick) and some gloop - no problems so far. Maybe add a filter check to the regular maintenance list...

Re: OT-Help needed on front-loader washing machine

#8

Re: OT-Help needed on front-loader washing machine

Bill Turpin in WNC mountains

On some top load washers there is a 1/4" ID plastic hose that goes from the side of the tub up to the water level pressure switch. As the level rises,the pressure trigers different steps in the control. Our tube every several years collects a clear gelatonous goo that stops up the tube. The goo comes out of our soap. Sticking a Q-tip up the tube will clean it out.

I don't know if front loaders have a similar system. It can be an almost invisible problem to figure out!