Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Craftsman Router 315.275110

Posts

Craftsman Router 315.275110

#1

Craftsman Router 315.275110

Gary Smyth

Looking for a 3.5 HP Craftsman Router 315.275110. Made by Ryobi. My router table is set up using this router. This was the original model router installed. What you see is a reconditioned backup. The original needed brushes and a brush tube, and springs and I ordered those. However, the brushes are mounted on a brush tube in a plastic or similar cylinder like brush holder( the original shattered when I open up the router.). After the electronic (no return) brushes, brush tubes, and springs arrived I'm advised by Sears the brush holder is out of stock and discontinued. Without it the other stuff is useless. Customer service at Sears is no help. Ryobi has no interest in telling me if any other models of their old Sears routers used the same brush holder. They do not have the personnel to tell me if their routers that they made for Sears has brush holders that matches up with any of their current Ryobi routers. The router originally was used as a stop gap install until I could afford a better one, but it kept going for fifteen years. It was going so well I bought a clearance back up which is now what is installed and pictured. This one may last fifteen years too, but I would rather go out now finding a parts machine, and a $4 part than to have to put in, at minimum, a new mounting plate, and new router, and perhaps a new top when I'm in the middle of some new project if and when this one bites the dust. I've tried the usual places Ebay, Craigs List, Router Forum... with no luck. I'm looking to find if anyone reading this has other options for me. By the way, the Sears part number for the brush holder is 970765-001 in case any other router has the same part number.

Re: Craftsman Router 315.275110

#2

Re: Craftsman Router 315.275110

Larry in NW OHIO

Gary I may have a couple of those routers, I`ll need to check the #`s and see if they are the same. Could it be possible to post a pic of the brush and holder to see if they are the same. Larry

Re: Craftsman Router 315.275110

#3

Re: Craftsman Router 315.275110

Joseph Mulherin

Gary, I had some problems with Black & Decker router brushes wearing out after many yrs, so I went online and looked at their offerings for brushes and found the ones I needed. I bought the router from Sears many yrs ago and parts were offered for it from them then.

The difference in the new brushes is the bronze contact plate on the end of the spring...needed to be exactly that way, but the ones the manufacturers use nowadays are very different and will not work in the older routers. Just a suggestion

Re: Craftsman Router 315.275110

#4

I'll get on it tomorrow AM.  You can contact

Gary Smyth

me away from this site if you consider moving one.

Re: Craftsman Router 315.275110

#5

Router brush holder photos

Gary Smyth



You can see that even the good brush holder is somewhat fried.

Look, I know that fifteen years use is a long run. But I still get ticked when you can buy parts that fit into an holder, but you can't get the essential item that holds that assembly together. I'd like to meet the guy that eliminated that part.

Larry, I didn't forget the photo of the brush. It is still in an unopened package. I'm going to try to make a case for return if I can't find a suitable replacement router.

Re: Craftsman Router 315.275110

#6

Re: Router brush holder photos

Stuart Johnson

Gary, I can't tell the size but could you rig up something from pvc or turn a wooden one? I agree about not being able to find parts on older items or spending way too much if you can. My wife has a 20 year old serger sewing machine that ran with out a bit of a problem until a small cast gear broke. The part is no longer available. I'm sure one could be machined but that would be one off and probably cost as much as a new machine.

Re: Craftsman Router 315.275110

#7

Re: Router brush holder photos

Larry in NW OHIO

Gary I looked a little this morning and all I could find was a complete router. I haven`t used it for a couple of years. If you would want the router if I can`t find the other parts, maybe we can come to an agreement. I just can`t believe I would have tossed the parts away since I`m a horder. I`ll keep looking. I even looked through EBAY this morning and saw nothing, I can harly believe that. Larry

Re: Craftsman Router 315.275110

#8

Larry, I agree.

Gary Smyth

Ebay has been barren of this model machine since at least 11/20/11. I check most days.

Contact me at my email if you are willing to make an offer. I don't think a transaction is appropriate (or permitted) at this site. Perhaps something can be done. Posting info on "Classified" page.

Re: Craftsman Router 315.275110

#9

Re: Craftsman Router 315.275110

George Colonel's Workshop-Havertown PA

Good Morning Gary,

I ran into a similar problem with Sears and my first (and only )Craftsman router. They couldn't give me parts support after a dozen years or so. Too bad. I liked the router. The exact same thing happened when my Craftsman compressor blew up. No way to obtain a replacement pump. I decided my best and cheapest course of action was to buy from manufacturers who would provide parts support...and abandon Sears completely. Sears lost my business permanently, and I won't even enter a Sears store.

George