Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

Wall shelf completed - now how do I hang it?

Posts

Wall shelf completed - now how do I hang it?

#1

Wall shelf completed - now how do I hang it?

Stephen Kirk

So, over a few weekends I knocked out this wall shelf for my wife to display some little curios. The plan is straight out of Fine Woodworking - I didn't feel like designing this time. Normally, this is made with all quarter sawn oak, but I used what I had on hand. It is mostly all 3/4" red oak. The columns are not solid but are mitered on the long edge. Shelves are just dado-ed in while the stretcher is M&T'ed.

The fun part of this project was getting over my fear of dyeing. I saw a lecture with Peter Gedrys a few months ago where he discussed dyeing and that it isn't that difficult. So, this project started with a coat of lemon yellow water based dye, moderately strong. At this point, I had a rather yellow project. I had very little grain raising, so instead of knocking it down I put on a coat of shellac, 2lb cut, clear. Then I sanded lightly. Then I followed up with Bartley's Dark Brown Mahagony gel stain (yeah, I still had some of that around!). I'd let it sit for a minute or two and then wipe it off. After it dried well, I wiped on 2 coats of Minwax satin poly - i figure it's a shelf and won't take much abuse so I'd only lightly finish it. I made a sample board, and if you just applied the stain, as opposed to the stain over the dye, there is a huge difference. My pictures can't do it justice, but dyeing, sealing and then staining really brings out the grain.

So, my last problem is how to hang it. I have some of the hangers that you mortise into the back which can accept a screw. However, the shelf weighs around 25 lbs and I'm worried about 2 molly bolts in drywall holding that. The columns are a distance apart that doesn't match up with studs. So, anyone have thoughts on hanging something like this? If you have any non wall damaging ideas, that'd be great.


Re: Wall shelf completed - now how do I hang it?

#2

Re: Wall shelf completed - now how do I hang it?

woodenleg

Why not use a small french cleat? My wife likes to move things around and the french cleat has proven to be a very good choice. Dave

Re: Wall shelf completed - now how do I hang it?

#3

Re: Wall shelf completed - now how do I hang it?

Stuart Johnson

Depending on how deep the back is inset you might be able to use a French cleat. I think you would need a half inch or better. If you can only hit one stud try and center it and then rather than a straight cleat on the wall make one that is "T" shaped with a couple lag bolt in the vertical part of the T and molly bolts in the ends.

Re: Wall shelf completed - now how do I hang it?

#4

I was going to suggest the same 


Re: Wall shelf completed - now how do I hang it?

#5

JL

Re: Wall shelf completed - now how do I hang it?

JL

French cleat or "Z" clip. The "Z" clips are less thick than French cleats. I've hung wall cabinets with "Z" clips before. Works quite well.

Re: Wall shelf completed - now how do I hang it?

#6

Re: Wall shelf hang up

Mark Mandell - Gone Round In Jersey

Since you've done a flush back, most anything you use will create a gap between the unit and the wall that will tend to interfere with the pilaster design posts on each end. About the only ways I know of to get/keep it all flush with the wall would be screws into the wall studs at the top of the interior (behind the valance piece) or a key-hole/stud arrangement. You can use the keyhole mount if your pilasters are spaced such that they line up with a pair of wall studs.

PS Having reread your post, I see the pilasters will not match a stud.

You can borrow a trick from the kitchen guys buy making a matching ledger strip that your bottom shelf will sit on to take the weight. That strip being screwed to the wall studs. Then use just 2 screws in behind the top valance to prevent the unit from tipping forward.

Re: Wall shelf completed - now how do I hang it?

#8

Re: Wall shelf hang up

Stuart Johnson

Since you've done a flush back,

It appears the back is inset a bit. I think the amount will determine if french cleats are doable without making some other changes.

Re: Wall shelf completed - now how do I hang it?

#9

Re: Wall shelf hang up

Barry Irby

If the back is inset 3/16 or a 1/4 inch you could buy strips of metal and make a very thin French cleat. If the metal is a 1/16 thick you make a shim half its width and slightly thicker. Then laminate it to the back of the metal to create a rabbet along one edge. Mount on on the wall with the rabbet up and the other on the shelf with the rabbet down and hang the cabinet like on a French cleat.

Wonder what the magazine suggested?

You could use Kreg screws in pocket holes from the top and under the bottom into studs.

The top shelf is pretty thick. You could screw metal plates onto the back of it with keyhole slots in them and then hang them over screw into studs. The plates could be let into the back of the shelf.

If the back really is flush, you could just lick it and stick in the wall like a big stamp. ;)

Re: Wall shelf completed - now how do I hang it?

#10

Re: Wall shelf hang up

Stephen Kirk

The magazine just suggested keyhole hangers recessed into the columns. But since the columns won't hit two studs, that's a lot of wait hanging in drywall.

I really like the idea of putting a small ledge for the shelf to rest on (attached to studs) and then just a few screws to keep it from tipping off. I could use the keyholes to do that. Make a small ledger board, finish it dark and it should. Ostly disappear.

The back isn't recessed at all, and those are just 3/16" ship lapped boards, no real strength there.

A stick on shelf is interesting, though.

Re: Wall shelf completed - now how do I hang it?

#11

Re: Wall shelf completed - now how do I hang it?

Larry in nw ohio

Stephen In Rockler they have a hanger that is called a "Flush Mount" that I use to hang things that are fairly heavy, and they work very well and the shelf will only hang out about 1/8" And from what I can see and reading the other posts, these might be just what you are looking for. You can put them on the back where ever the studs are. The number is 29975 or29983. Good luck Larry