Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

Big Box Lumber Rant

Posts

Big Box Lumber Rant

#1

Big Box Lumber Rant

Thomas Skaggs, Foothills of Mount Level

So I have been building some lumber storage racks for the new shop. I'm using a lot of 2X4 material as well as 2X6 stuff. For a while now I have found that my "top choice" lumber comes adorned with a UPC stapled into the ends of each board. Those, along with the stickers plastered on sheet goods provide me with "the opportunity" to waste my time removing them.

But lately I have been plagued by larger wire fasteners that are fired into the wood for holding binding straps. This weekened I realized that 4 out of the 10 2Xs had them. These aren't tiny staples, these are wires that are large enough to not only damage tools but damage ME as well. I don't know if just our local "top choice associates" have become too lazy to remove all those wires but a word of caution...check every piece before you cut!!

Tom

Re: Big Box Lumber Rant

#2

Re: Big Box Lumber Rant

Larry in nw ohio

I`ve gotten to the end of my rope with the box stores, one of the better one that I liked nixed the 105 of for veterans, so I stopped going there unless I need to, really need to, really, really need to. I`m starting to go back to Carter lumber, the only thing they only have lumber, not any of the other things. No real big deal anyway. Larry

Re: Big Box Lumber Rant

#3

Re: Big Box Lumber Rant

Stephen Kirk

I grabbed a bunch of dowels recently. I can deal with not everything being straight, but they like to mark everything with stickers. Stickers which stick really well and leave a nice gummy residue. One more thing to clean off the wood.

Re: Big Box Lumber Rant

#4

Sooner or later...

Bob Hackett

We`ll reach the tipping point where it`ll be less trouble to hunt up a local sawyer and get lumber the way we used to,from local vendors who cut local trees.

I look forward to the rest of the country getting back to the basics we haven`t forgotten up here in Maine.

Re: Big Box Lumber Rant

#5

I specifically bought...

John in NM

A pocket knife with a punch awl blade so that Jean wouldn't keep bending my regular blade - she's seen me use it to remove these various fasteners but never got the hang of rolling the blade once under the staple so that the blade doesn't bend.

Never had to remove the bigger ones, just a few medium ones that hold the shipping wrap on (there's usually a dozen or so if you get a 2x that has them).

Any more I'm just happy to get 2x lumber that is actually 1.5x 3.5,5.5,7.25 instead of 1/16 to 1/8 under. I hate thieves :D

Re: Big Box Lumber Rant

#6

Re: Big Box Lumber Rant

Larry Barrett

Until recently most of the dowels I bought from HD or Lowes had Made in China stickers on them, and were often undersized to boot. I bought some a week or so ago (Lowes) that were made in USA and were proper size. Still had stickers, though. Heat gun helps to get them off, but still need MS to get gummy residue off.

Re: Big Box Lumber Rant

#7

Re: Sooner or later...

Stephen Kirk

I still cut and dry lumber myself I'll use local guys with band saw mills and kilns for that. 'Bout the only lumber I get from Borgs is framing material for the rough projects around the farm. For other fine lumber, I go to specific lumber dealers, I'm lucky to have 3 within about a 2 hours drive.

Re: Big Box Lumber Rant

#8

Re: Big Box Lumber Rant

Howard Acheson

>>>> I bought some a week or so ago (Lowes) that were made in USA and were proper size.

It's best to use your drills and drill a sample hole of each size in a piece of plywood. They take this sample block with you "fit" any dowels you buy. That way you will get dowels that fit the holes you drill. It's always risky these days to just take pot luck in a store.

Re: Big Box Lumber Rant

#9

I miss it...

John in NM

One place I lived (Caratunk :D ) there was a mill down the road, run by guys my dad had known his entire life. I only remember buying 2x stuff there, but I think they may have milled local maple too. I remember being told most of the birch went for pulp at the time, might still if they still make paper in Maine.

Re: Big Box Lumber Rant

#10

Re: Big Box Lumber Rant

Barry Irby

I too hate the Staples. The little ones in the ends don't bather me so much but the big ones they use on the edges to hold the shipping covers on are a PITA. Recently I cross cut a borg 2x4 with my WWII blade and hit the leg of one of them that had broken off in the piece. I "ripped" the leg of the staple, leaving about half of it in the wood. About 3/4" long. Major bummer. There are some chips in the carbide. The blade still cuts well but not quite up to par.

Re: Big Box Lumber Rant

#11

Re: Big Box Lumber Rant

Jesse Cloud

Being a believer in capitalism, I would like to think that if we stopped buying this crap, they would improve their offerings. Problem is that the big buyers of dimensional material at the big boxes are small contractors who just want the lowest price. Their air nailers shoot right through those staples and if the lumber is bowed or cupped or whatever, well blame the finish carpenter for shoddy work.

Re: Big Box Lumber Rant

#12

Re: Big Box Lumber Rant

Jim Runchey

I just dis-assembled a workshop cabinet I had made back in the 50's or 60's, with 2 x 4's that were 1 1/58" by 3 5/8". What a difference from today's lumber. Tiny tight knots, straight as an arrow, beautiful stuff. Cut from much larger trees than the current stuff.

Re: Big Box Lumber Rant

#13

Re: Big Box Lumber Rant

Tom Dunlap

What a difference from today's lumber. Tiny tight knots, straight as an arrow, beautiful stuff. Cut from much larger trees than the current stuff.

I read a book a while ago called 'A Forest Journey' by Perlin. It traces the use/abuse of wood in civilizations from ancient Greece up to the US. It is pretty easy to see a pattern...once the trees are gone the civilization declines. Tree use/abuse is the canary in the coal mine.

Now that we are a world civilization the leap, to me, is easy. Consumers reach further and further from 'home' to get the raw materials needed.

Re: Big Box Lumber Rant

#14

Night and Day

Thomas Skaggs, Foothills of Mount Level

A while back I did some renovation on our last house. It was built in the 20's. I tore out some studs to re-use. I needed some new ones too. At one point I remember standing there with an old stud in one hand and a new one in the other. The weight difference was amazing. The new stud felt like Balsa Wood in comparison. And they build entire homes with this stuff? Scary!

T.