We value your privacy.
We use cookies to enhance your browsing experience, analyse site traffic, and personalise content.
By clicking “Accept all”, you consent to our use of cookies. You can also choose
“Essential only” or learn more.
I am spending the week with family in Atlanta, and am debating whether a visit to Highland Woodworking is worth the drive into downtown Atlanta. Anyone ever been there?
Well, driving in Atlanta, downtown or not, is an unpleasant experience but I'd say that Highland is worth it. You might think about a circuitous route to get there to avoid cutting through downtown at bad times which in my experience is most of the time. They are off on the edge of the worst area and driving twice as far to get there still might save time.
Michael, you won't see anything there that you won't see in any other woodworking supplies store, unless you happen to be there on a day when there is a demonstration by a well-known woodworker. It's got a wooden floor and a balcony shopping area and it's in a vintage building in an eclectic part of town.
There are lots of good things to see and places to go in Atlanta. If you've been in other stores that cater to woodworkers, as I have, then I'd rather enjoy the sights of the city. Stone Mountain, Centennial Park, the Swan House, the Wren's nest, Callaway Gardens / Warm Springs if you're up for a drive, the CNN Center, the World of Coke, Underground Atlanta, Little Five Points, the Georgia Aquarium are all good choices, as is Virginia-Highlands, where Highland Hardware is. ..Too many to give adequate mention.
You must have better woodworking stores in your area. Highland has lots of things we don't have around here. They have things that Woodcraft doesn't have as well. I always enjoy going there. My pocket book doesn't, I always find something I have to have.
It's about a 30 minute drive from my parents house. Traffic isn't that bad unless you try to go during rush hour. Then it's rediculous. There are some great shops to go in besides Highlands.
It is worth going there. But go there with a budget - or you will spend entirely too much money.
If you have the space and the time, consider going to Atlanta Wood Products. They are on the perimeter (I-285). They have an excellent selection of wood and veneers at reasonable prices. I always like going there to see what they have. They used to cut off lengths of wood from the boards, providing that you left at least 6 linear feet of board. I don't know what they do now.
Atlanta Wood Products may now be called Atlanta Hardwood or Hardwoods, Inc. It's one of many good places to find lumber in Atlanta, if that's what you're looking for. They're an especially good source for sheet goods. If you're interested in exotics and/or veneers you've got to check out Carlton's Rare Woods and Veneers on Hemphill Ave. next to the Georgia Tech campus.
As an addendum : Check out their website if you care to see what a given species of wood looks like.
I have been to Highland Hardware several times and would go again in a minute, except I live in VA and They are in GA.
When we were there "shopping" I stumbled onto a mortiser like the one David Marks had on his show. There was a mount on it for a Router (not present) and it had a table to clamp the work to. There were three levers, one for the X Axis and one for Y and another for Z. I had never seen such a thing and was trying to figure out what it was, playing with the handles. Another guy walked up and asked me what it was. I said, I don't know. He said, "Me neither, but I want one, It has a high Gizmology Factor". Me too.
I also agree with all the places mentioned you should visit. And Atlanta Wood Products or whatever they call themselves now is well worth a visit. One of the things they had that I still want was "Backer Boards". ( I Hope I remembered that correctly.) These are the board left when they have sliced as much veneer off it as they can. They were about 5/8" thick and someof the finest wood I ever saw. Not terribly expensive either.
Also, Go Eat at Mary Macks, A local landmark restaurant. Its too long a story, but Its in my top three.
I try to go every time I get to Atlanta and they beat any woodcraft store I have been to. Have spent some good money there also but has always been quality stuff. And the people that work there have always been good and knowledgeable.
But do not even think of going during rush hour! I find best 1st thing Sat morning before everyone get's up and going.
But watch your wallet. The place is sort of like a big barn with a balcony or loft around it. The place is loaded with tools of every sort, all high quality. It would be easy to drop ten thou or so......
I took a turning class there when I was in town on a business trip and learned a lot.
I only live a couple of hours away from ATL but I stop by the store every time I am in ATL. I have rarely had any problems driving from downtown ATL to the Virginia Highlands area.
The store never disappoints....and they sometimes have some sort of special event on the weekends.
Virginia Highlands is generally a fun area to walk around, eat, drink, shop, etc....
Well, I made to highland. I made it out for less than $200. I ended up getting some Veritas dovetail guides, a carving knife, and a Lie Nielson low angle block plane. My wife wasn't too upset, she just informed me that I has just purchased my own Christmas present; I'm ok with that.
Ellis, I put in a good word for WC. Thanks for the input everyone. It was definitely worth it.