Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

OT Help w/ Lawn Tractor Screw fix

Posts

OT Help w/ Lawn Tractor Screw fix

#1

OT Help w/ Lawn Tractor Screw fix

Gary Smyth

Several weeks ago the throttle spring on my 1450 Cub lawn tractor broke. When I took off the air cleaner assembly to fit the spring found the old carburetor gasket split. I removed three screws and replaced the old gasket with a new at that time. Today I found the new gasket in the driveway. When I checked the air cleaner cover, I found all three 10 x 32 x ½ gasket screws at the bottom. I thought that I Loctited them in but apparently not. Now I find that they are loose in their proper location. Only one holds well and the other two are very wobbly. I’m hoping not to have to search out a new, and expensive (old stock) carburetor (it's a 1974). Can I tap the screw locations to a different size? I have taps but not a bottoming tap. Do they make helicoils that size? Never done it before on a carburetor. Looking for suggestions how to make a fix so that I have three secure screws. By the way, I have to be able to remove them so permanent, permanent is not an option.

Re: OT Help w/ Lawn Tractor Screw fix

#2

Re: OT Help w/ Lawn Tractor Screw fix

Tom Dunlap

YOu might be able to drill/tap oversized if there's enough meat there.

If you don't have a bottoming tap you can MacGuyver one quite easily. Use your normal tap to cut the threads at the 'top' of the hole. Back it out...blow out the debris. Take a second tap and grind off the tip and most of the cutting/tapered threads on the leading edge. Use this as the bottoming tap.

LockTite does make a 'Thread Repair' compound too. I've used it with great success. First you tap out the threaded part with a normal tap. Clean out the hole, I use carb or brake cleaner followed by air. Then you drip in some of the LockTite compound. A release agent is applied to the screws and they are threaded into the hole on top of the repair compound. This compound fills the gap between the jimmied threads and the good threads of your screws.

You should probably run the screws through a die to straighten up and rolled threads and clean with carb/brake cleaner too.

Re: OT Help w/ Lawn Tractor Screw fix

#3

Re: OT Help w/ Lawn Tractor Screw fix

John Veerkamp

Be sure to use new screws. They are probably worn down some also.

Re: OT Help w/ Lawn Tractor Screw fix

#4

Re: OT Help w/ Lawn Tractor Screw fix

Larry in nw ohio

Gary If they are 10-32, the next size up would be 12-32 or something like that. 12`s aren`t very easy to find sometimes but they are around. Around here Menards has them. If there is enough meat to upsize them, that`s the way to go. Good Luck. Larry

Re: OT Help w/ Lawn Tractor Screw fix

#5

Re: OT Help w/ Lawn Tractor Screw fix

Bill Houghton, Sebastopol, CA

The only commonly available step up from #10 machine screws is 12-24 (coarse thread pattern); and my local hardware store, an excellent store (mechanics will drive from adjacent towns to shop in it), carries just a few patterns (head size, etc.).

You might look at a metric screw - perhaps a standard metric machine screw is just a little larger than a #10. You can then confuse yourself or future repair folk by having metric in one place on the tractor.

If you have a bench grinder, a bottoming tap is easy enough by grinding down an extra tap; but, if you're going to go oversize, you might see if you can find a self-tapping machine screw in that size instead - although self-tapping screws can't be cut easily (you lose the self-tapping feature, and they're often hard to cut anyway), so you need to see if the length is right.

Be sure, of course, to stuff paper towels in the air opening; and, if you're tapping, use grease in the flutes of the tap to retain the chips, wiping it out as needed when the flutes fill.

Re: OT Help w/ Lawn Tractor Screw fix

#6

Thanks. I caught a break

Gary Smyth

I retapped the screw hole at the existing 10 x 32 and was able to go a bit further in than the 1/2" screw that was there. I used a new 10 x 32 x 3/4" with a lock washer to take up the difference with blue Loctite and was able to get purchase. It may or may not work in the long term, but it will get me through the last of the Fall cuts (I hope) until I can find a size 12, metric 5.5, or decide to buy a 10 x32 helicoil kit ($30+).

Re: OT Help w/ Lawn Tractor Screw fix

#7

Re: Thanks. I caught a break

Brian Anderson Gunsmith

Do remember that blue loctite can be loosened with heat.

Re: OT Help w/ Lawn Tractor Screw fix

#8

Didn't know that.  Red is permanent

Gary Smyth

and I will need a blowtorch to get it off. Not a good idea at a carburator. Other suggestion?

Re: OT Help w/ Lawn Tractor Screw fix

#9

Re: Didn't know that.  Red is permanent

Brian Anderson Gunsmith

I am not certain that a blow torch is necessary to remove the blue.

Particularly where there is a certain operating temperature.

What I forget is the actual temp needed.

A loctite webpage should/could have the numbers.

Re: OT Help w/ Lawn Tractor Screw fix

#10

Re: Didn't know that.  Red is permanent

Brian Anderson Gunsmith

Just found a reference loctite blue 242 says -65 degrees to +300 degrees F

So perhaps a torch may not be needed.

Re: OT Help w/ Lawn Tractor Screw fix

#11

Jim DeLaney, Austintown, Ohio

Re: Red is permanent - Soldering Iron

Jim DeLaney, Austintown, Ohio

Gary,

The heat of a soldering iron is enough to soften Loctitie when the screws are fairly small.. Just hold the iron on the screw head for a minute or so, and then (quickly) back the screw out.