Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Mind your drawer thicknesses

Posts

Mind your drawer thicknesses

#1

Mind your drawer thicknesses

Bill Tindall

Daughter called. She hand been to a crafts fair and she had seen what appeared to be, from the outside, a beautiful small cabinet, well designed and executed with exquisite wood selection. But when she opened the drawers they had thick sides, all out of proportion to the size of the piece. Her impression of the piece sank.

I agree with our English Forum participant that American made drawers tend to be too thick. Drawer sides do not have to be thick to be durable. The drawer sides on English furniture may only be 3/8" on a large chest of drawers. The bottom line is that the thickness of the side should be proportioned to the size of the piece. Thinner sides, and bottoms, are have stood the test of time in English furniture.

Personally, I have not been bold enough to make a large drawer at 3/8" using poplar, but mine have thinned to less than 7/16" for a large drawer and even less for smaller drawers. The result is a lighter weight drawer that looks good upon opening it.

Re: Mind your drawer thicknesses

#2

Re: Mind your drawer thicknesses

John McGaw

On average I guess my drawer sides tend toward 1/2" although I sometimes taper the inside of the tops a bit to make them visually thinner. My free interpretation of a Shaker pegleg sewing stand has 0.387" (by digital caliper) sides and my sycamore hall tables has small drawers with sides at 0.382". Both of these have hard maple sides. On the other hand the tiny drawer in my cherry dropfront desk has 1/2" sides. I can't say that any of this is a matter of design or even intent since I don't do drawings and don't do any planning beyond the mental. Things happen as they happen.

Re: Mind your drawer thicknesses

#3

Re: Mind your drawer thicknesses

roger lance

At what thickness do you begin to install slips ??

Re: Mind your drawer thicknesses

#4

Re: Mind your drawer thicknesses

Yonak

I like to make drawers as wide as possible, especially narrow drawers, so I have begun cutting dados to fit about half the depth of the drawer slides, which not only increases the width of the drawer, but also decreases the bothersome gap between drawer and frame. If I went with a 3/8" thick drawer side it wouldn't leave enough meat to attach the slide, unless I use a bolt and a nut, that leaves a visible head on the inside of the drawer (which I have done, when I didn't have a choice).

So I have come to 9/16" drawer side thickness as a compromise, unless it's on a petite cabinet where it would look too heavy (and which wouldn't use drawer slides anyway). To me it looks solid and serviceable but not out of proportion.

Re: Mind your drawer thicknesses

#5

Well that is a good question

Bill Tindall

I hope someone experienced answers. I have only recently begun to experiment with slips so my opinion is of little value, for I have little experience. I have been using them on large drawers with 7/16" sides. The are so easy to install that I used them even on the small drawers of the latest chest of drawers. The dado into a thin side becomes a issue so the function of the slip could be to provide a groove for the drawer bottom as much as provide enhanced bearing surface.

Re: Mind your drawer thicknesses

#6

Re: Mind your drawer thicknesses

FredD

Standard side mount slides will install on a 3/8 " drawer with no penetration to the inside.

Many of the screws , if not most are 5/16" long.

FredD

Re: Mind your drawer thicknesses

#7

Agree for guided drawers...

John in NM

I tend to go 1/2" or a bit thicker with guided drawers. If the sides were maple I might go a bit thinner as Fred mentions. I'm scarred from years in a shop where alder was the drawer material (need a gag smilie :D ).

However, what Bill's referring to are un-guided drawers (hence the talk about slips).

Re: Mind your drawer thicknesses

#8

The Thicker, The Better, In Very Cold Weather

George Colonel's Workshop-Havertown PA

I mill mine to between 3/8 and 1/2". I don't sweat out the proportion of the drawers relative to the size of the piece. I like 1/2" for most of the furniture I make. The proportion of the furniture case work is the more important consideration. When the drawers are closed, who cares what the thickness of the drawer side is? When I see a drawer left open, I close it.

George