Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

Progress on chest of drawers

Posts

Progress on chest of drawers

#1

Progress on chest of drawers

Bill Tindall


Four drawers down and 3 to go on this "3/4 sized" chest of drawers for granddaughter. In addition to the three drawers I need to make a top(easy), fit the bull nosed facing on the front(not easy) and add a skirt (moderate) and finish(easy).

The drawers are face veneered with some resawed cherry. Some would claim that anything that is veneered on one side needs to be "balanced" by veneering the other side. However, the personnel in a 4th generation cabinet shop said they had never seen the inside of a drawer veneered in Period furniture and my experience would confirm it indeed is unnecessary.


This back view shows better the dovetailed case construction. Dovetailing the back drawer dividers is overkill but I'm not trying to make a living doing this piece, so why not.

All the wedges and putty knives sticking out of drawer 4 are there to center it whilst the glue dries. I let the glue(liquid hide) dry with the drawer in place and centered in opening. No question that it will fit properly with this approach.


This view shows the drawer construction. I am using slips on these drawers. They are unnecessary on the small top drawers but practice here will make installation easier down below on the big drawers. Note the variety of wood. I use up junk in drawer backs and bottoms. Sides are quartered poplar. Runners are maple for durability.

Re: Progress on chest of drawers

#2

Re: Progress on chest of drawers

George Colonel's Workshop-Havertown PA

Careful and meticulous work, Bill. Its true Crasftsmanship which I wish my own work displayed.

George

Re: Progress on chest of drawers

#3

Re: Progress on chest of drawers

Jesse Cloud

Truly a beautiful piece Bill. Can't wait to see it finished.

I can't resist a comeback to your comment about veneering both sides. Common sense should apply. The issue is that by covering the face of the substrate with glue, one adds a lot of moisture to the veneered side. With a thin substrate, a single veneer face produces a curve in no time at all - I have seen it. Veneer one side of some 1/4 mdf if you are skeptical. However, your drawer has a sturdy substrate and the drawer front is amply held in place by mechanical means (dovetails), so no need for veneer on the inside of the drawer.

By the way, same thing goes for applying a finish to both sides. Stickley, for one, never finished the underside of a table top...

Re: Progress on chest of drawers

#4

Bill, This would be a perfect project,

Keith Newton----Little Rock, Arkansas

to use some thickened epoxy for that veneer. It has no water, to change the MC of the veneer, or substrate, so if both are at EMC now, there should not be any problems down the road.

I'm sure that you are trying to work in the traditional methods, but if you ever worked in some of those Blum under-mount slides with the soft close into one of these projects, the recipients would simply be elated by the improvement.

Nothing shows from the front. Full extension even shows the back set of tails, plus everything in the drawer. They glide without any effort, then take over and finish closing slowly on their own like magic.

Re: Progress on chest of drawers

#5

Since you brought it up--

DizD

I just shipped this off a couple of weeks ago. It has the undermount slides - the second piece I've done with these.


After I saw the photo I noticed the top center drawer face is darker than the others - each set of the drawer fronts were made from a single board and treated the same as far as I know. I also used housed dovetails for the drawer dividers for the first time. Wood is walnut salvaged after hurricane Hugo which hit 22 years ago today.

Re: Progress on chest of drawers

#6

nothing mechanical beats well fitted trad. drawer

Bill Tindall

The secret to a smooth as silk traditional drawer is the fit and finish. Note the fit of the top two drawers (these have been fitted, the larger ones have not yet).

I build the drawers to just fit the opening, then hand plane to get the clearance needed. I also use maple runners and wax them. And, I shellac the drawers and inside of the case which leads to little friction and no racking.

The result is a drawer that can be smoothly closed with one finger pushing against any corner....that is my quality control criteria.

I use mechanical devices on kitchen and other utility drawers only.

Re: Progress on chest of drawers

#7

Experience trumps common sense

Bill Tindall

See comment from an antique restorer on hand tool side. His experience matches that of the Headley shop. Together they have examined hundreds if not thousands of drawers in Period furniture and not often encountered a drawer veneered on both sides. I have let drawer fronts sit about for weeks before assembly with no movement observed. A friend veneered one side of a test drawer front years ago and he has been watching it for these years and seen no movement resulting from the one sided assembly.

I have only have 2 years experience with one sided drawers so I have little additional experience to add to the discussion. When in doubt I do what experienced shops do. The Headley shop has 4 generations of experience plus two generations ran an antique store.

Re: Progress on chest of drawers

#8

Re: Progress on chest of drawers

Greg Muller

Bill,

I am awed by your level of craftsmenship. I can'r wait to see the final project. Is this a design of your own and if so can you send me some rough dimensions. My next project is going to be a chest of drawers for my sons and I have not found a set of plans that fit my needs. This will be my first chest of drawers so I am doing as much research as possible. Your design matches very closely what the wife asked for. If you are working from a set of plans can you let me know who's plan it is. Thank you.

Re: Progress on chest of drawers

#9

"plans" are your for the asking

Bill Tindall

I never have built anything from plans. I can never figure them out. I draw up something on paper to scale and diddle with it till the proportions look right. I will email you with dimensions.

Re: Progress on chest of drawers

#10

Re: "plans" are your for the asking

Greg Muller

That would be great. Thank You.

Re: Progress on chest of drawers

#12

PS- a comment on small drawers

Bill Tindall


This is a larger chest of drawers that we use in bedroom for clothes storage. The three small drawers at the top have proven to be functional. At first I wondered if they were too small to be useful but in fact they are just right for socks, for example. I intend to put some small drawers in the top of any chest of drawers I build.

Re: Progress on chest of drawers

#13

That's a beautiful chest !!


Re: Progress on chest of drawers

#14

A Question???

Barry Irby

If the side of the chest is solid wood, how do you accommodate the differential expansion between it and the dust panel? If the dust panel were frame and panel there would be a cross grain connection "in the Dado" in the side of the chest. (Right?) So how do you allow for that?

Wonderful little chest. Could you send me the dimensions also. I have granddaughters and a nephew in need of chests.

Re: Progress on chest of drawers

#15

Dust panels are a waste of time and wood

Bill Tindall

Note there are no dust panels in this chest. Runners float in mortises. 17" deep, 27 1/2 wide and 49" tall.

Re: Progress on chest of drawers

#16

Yeah but...Thems classy....

Barry Irby

It has got to be a personal prejudice thing. I think dust panels are classy or a mark of classy furniture.

Thanks for the dimensions.

Re: Progress on chest of drawers

#17

Re: Yeah but...Thems classy....

FredD

Barry you would be right in thinking that Dust panels are a hallmark of a furniture maker.

They serve at least three functions, by keeping out airborne dust , stiffening the case and allow you to make a snug fit for the drawer box top to bottom without tipping down when you open it.

Depending on your attitude about the interior construction of the case and your willingness to cut corners , they are a very worth while effort and a detail not over looked by Buyers.

This is one I did for a friends Wife.

https://picasaweb.google.com/FredD17209/TripleDresser?authuser=0&feat=directlink

Re: Progress on chest of drawers

#18

One handsome chest of drawers......

Bill Tindall

I especially like the pulls.

Re: Progress on chest of drawers

#19

Re: One handsome chest of drawers......

FredD

Thank you Bill , about the pulls , they constituted a larger amount of meticulous cutting and fitting , then probably any other part of the Chest.

FredD